PM 4-M Operating instructions en ja ko zh cn Printed: 08.07.
1 Printed: 08.07.
2 3 4 5 6 7 8 Printed: 08.07.
9 ´ PP P IW P $ % $ % $ G Printed: 08.07.
12 11 d1 b max. 3mm d1 d3 b 2 5 5m a c a 3 d2 4 1 13 14 max. 3mm d1 d3 b a d0 5 3 6 d2 c 7 15 d1 d0 d2 7 6 5 Printed: 08.07.
16 T1 2.5m 2m Pos. 1 T2 90p Printed: 08.07.2013 | Doc-Nr: PUB / 5130903 / 000 / 02 2.5m Pos.
ORIGINAL OPERATING INSTRUCTIONS PM 4-M multi-line laser It is essential that the operating instructions are read before the tool is operated for the first time. Always keep these operating instructions together with the tool. Ensure that the operating instructions are with the tool when it is given to other persons.
On the tool en Laser radiation. Do not look into the beam. Laser class 2. Laser warning plate according to IEC60825/EN608251:2007 Location of identification data on the tool The type designation and serial number can be found on the type identification plate on the tool. Make a note of this data in your operating instructions and always refer to it when making an enquiry to your Hilti representative or service department. Type: Generation: 01 Serial no.: 2 Description 2.
2.4 Information displayed during operation LED The LED does not light. The tool is switched off. The LED does not light. The batteries are exhausted. The LED does not light. The batteries are inserted incorrectly. The LED lights constantly. The laser beam is switched on. The tool is in operation. The batteries are almost exhausted. The LED blinks twice every 10 seconds (pendulum not locked) or every 2 seconds (pendulum locked). The LED blinks.
Self-leveling time 3s Laser class Class 2, visible, 635 nm, ±10 nm (EN 60825-3:2007 / IEC 60825 - 3:2007); class II (CFR 21 §1040 (FDA) Distance 5 m: < 2 mm Line width en Self-leveling range ±4° (typical) Automatic power-off Activated after: 1 h Operating status indicator LED and laser beams Power supply AA‑size batteries, Alkaline batteries: 4 Operating time (all lines on) Operating temperature Alkaline battery 2,500 mAh, Temperature +24°C: 7 h (typical) Min. -10°C / Max.
r) s) tronic instruments (e.g. binoculars, spectacles, cameras) it should be treated with care. Although the tool is protected to prevent entry of dampness, it should be wiped dry each time before being put away in its transport container. Check the accuracy of the measurements several times during use of the tool. 5.2 Proper organization of the workplace Secure the area in which you are working and take care to avoid directing the beam towards other persons or towards yourself when setting up the tool.
4. en Close the battery compartment. Check that the catch engages properly. 7 Operation 7.2.1 Transferring heights 3 7.2.2 Setting out drywall track for a partition wall 4 5 NOTE To achieve maximum accuracy, project the line onto a vertical, flat surface. When doing so, set up the tool at 90° to the surface. 7.1 Operation 7.1.1 Switching the laser beams on 1. 2. Unlock the pendulum. Press the on/off button once or repeatedly until the desired operating mode is set.
7.3.2 Checking the leveling of the horizontal laser beam 10 1. 2. 3. 4. 5. 6. 7. 8. 9. Place the tool on an even, level surface approx. 20 cm from the wall (A) with the laser beam directed toward the wall (A). Mark the point of intersection of the laser lines on the wall (A) with a cross (1). Pivot the whole tool through 180° without using the rotatable housing and mark the point of intersection of the laser lines with a cross (2) on the wall opposite (B).
6. Now place the tool on the floor on the mark for position 2 which you have just made. Direct the laser beam toward the target plates T1 and T2 so that it strikes the plates close to their center lines. 7. en Read the distances D1 and D2 from each target plate (distance of the laser line from the center of the target plate) and calculate the difference (D = D1 - D2). NOTE Take care to ensure that the target plates are parallel to each other and that they are in the same vertical plane.
Fault Possible cause Remedy Automatic leveling doesn’t function. The tool is set up on an excessively inclined surface. The tilt sensor is faulty. Set up the tool on the level. If necessary, have the power tool repaired by Hilti Service. en 10 Disposal WARNING Improper disposal of the equipment may have serious consequences: The burning of plastic components generates toxic fumes which may present a health hazard.
Hilti Corporation Printed: 08.07.2013 | Doc-Nr: PUB / 5130903 / 000 / 02 2049370 / A4 2049370 Hilti = registered trademark of Hilti Corp., Schaan W 4207 | 0413 | 00-Pos. 2 | 1 Printed in China © 2013 Right of technical and programme changes reserved S. E. & O. *2049370* LI-9494 Schaan Tel.: +423 / 234 21 11 Fax: +423 / 234 29 65 www.hilti.
