User's Manual

ManualsBrandsHilti ManualsDrillsDrill Guide

User Manual.doc Seite 1 von 9

PX 10 Transpointer - Operating Instructions

______________________________________________________________________________

It is essential that the operating instructions are read before the tool is used for the first

time.

Always keep these operating instructions together with the tool.

Ensure the operating instructions are with the tool when it is given to other persons.

Contents

1. General information

2. Description

3. Tools and accessories

4. Technical data

5. Safety precautions

6. Before use

7. Operation

8. Applications

9. Calibration

10. Care and maintenance

11. Disposal

12. Warranty

13. FCC and IC statements

14. EC declaration of conformity

Component parts

1. Transmitter PX 10T

2. On/Off key

3. Status indication light

4. Indentations for adhesive putty

5. Battery compartment

6. Hand strap PDA 60

7. Receiver PX 10R

8. On/Off key

9. Direction arrows

10. Display

a. Battery status

b. Signal status

c. Measuring units

d. Distance

11. Marking notch

12. Battery compartment

13. Hand strap PDA 60

14. Slope adapter PXA 70

15. Holder for PX 10R

16. Scale showing angle of measurement

17. Adjustment thread

18. Reference point

19. Marking notch

1. General information

1.1 Safety notices and their meaning

-WARNING-

The word WARNING is used to draw attention to a potentially dangerous situation which could lead to severe personal

injury or death.

-CAUTION-

This word indicates a possible hazardous situation which could result in slight bodily injuries or damage to property.

Gelöscht: E_Transpointer_PX

10_22.01.06

Summary of content (9 pages)

PAGE 1
PX 10 Transpointer - Operating Instructions ______________________________________________________________________________ It is essential that the operating instructions are read before the tool is used for the first time. Always keep these operating instructions together with the tool. Ensure the operating instructions are with the tool when it is given to other persons. Contents 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
PAGE 2
-NOTEDraws attention to instructions and other useful information. 1.2 Pictograms Warning signs Symbols 1 These numbers refer to the corresponding illustrations. The illustrations can be found in the fold-out cover pages. Keep these pages open when studying the operating instructions. In these operating instructions, the PX 10 Transpointer is referred in it’s two components. The PX 10T as the “transmitter”. The PX 10R as the “receiver”. Or in general as the “tools”. 1.
PAGE 3
2.3 Measuring principle The transmitter generates a magnetic field. This field can penetrate bricks, wood, concrete, and concrete with metal reinforcement. The field is however affected by metal. Whilst normal reinforcement in concrete is not a problem, welded reinforcement, reinforcement mesh, flat metal sheet or massive metal beams can have a considerably negative effect on the system performance.
PAGE 4
- Observe the information printed in the operating instructions concerning operation, care and maintenance. Keep tools out of reach of children. Have the tool repaired only at a Hilti service center. Take the surrounding conditions into account. Do not use the tool where there is a risk of fire or explosion. Check the operating mode of the tool before each use. The tool should not be used near pregnant women. Avoid contact of the eyes and skin with PUA 91.
PAGE 5
7. Operation 7.1 Switching on/off Press the on/off key 7.2 Setting up the transmitter The transmitter should be fixed over the reference point using the center hole and the outer marks on the tool. Two different adhesives are provided to help with this. The tool may also be held by an extra person, or hung from the hand strap for added security. -CAUTIONIt is recommended where possible to use the adhesive putty.
PAGE 6
- Have the PX 10T stable and make four measurements with the receiver from each side mark them and take the geometrical center In cases where the walls are possibly not parallel take four measurements. Each time rotating the PX 10T by 90° and take the geometrical center In case of heavy metal in or close to the wall perform a couple of measurements at known distances and take the geometrical centre. (i.e.
PAGE 7
8.3 Transferring marks Transferring alignment marks or points through walls/ceilings/floors. 8.4 Measuring wall thickness To determine the thickness of walls/ceilings/floors. 9. Calibration We recommend that the tools are checked by the Hilti Calibration Service at regular intervals in order to verify the reliability in accordance with standards and legal requirements. Use can be made of the Hilti Calibration Service at any time, but checking at least once a year is recommended.
PAGE 8
11 Disposal -CAUTIONImproper disposal of the equipment may have serious consequences: - The burning of plastic components generates toxic fumes which may present a health hazard. - Batteries may explode if damaged or exposed to very high temperatures and thus cause poisoning, burns, acid burns or environmental pollution. - Careless disposal may permit unauthorized and improper use of the equipment, possibly leading to serious personal injury to third parties and pollution of the environment.
PAGE 9
Information plates on the product: 14 EC declaration Designation: Type: Year of design: Transpointer PX 10 2006 In conformance with CE We declare, on our own responsibility, that this product complies with the following directives and standards: EN 300 330-2, EN 301 489-3 V1.4.1, EN 60950-1:2001/IEC 60950-1:2001 Hilti Corporation Matthias Gillner Head BU Measuring Systems 04 / 2006 Dr.