ICC-ES ESR-4878 for HIT-HY 200 V3

ManualsBrandsHilti ManualsFastenersHIT-HY 200-R V3 Adhesive anchor

Table Of Contents

ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed

as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as

to any finding or other matter in this report, or as to any product covered by the report.

Copy

www.icc-es.org | (800) 423-6587 | (562) 699-0543 A Subsidiary of the International Code Council

ICC-ES Evaluation Report Issued November 2021

ESR-4878 This report is subject to renewal November 2022.

DIVISION: 04 00 00—MASONRY

Section: 04 05 19.16—Masonry Anchors

REPORT HOLDER:

HILTI, INC.

EVALUATION SUBJECT:

HILTI HIT-HY 200 V3 ADHESIVE ANCHOR SYSTEM

1.0 EVALUATION SCOPE

Compliance with the following codes:

 2021, 2018, 2015, and 2012 International Building Code

(IBC)



2021, 2018, 2015, and 2012 International Residential

Cod

(IRC)

For evaluation for compliance with codes adopted by Los

Angeles Department of Building and Safety (LADBS), see

ESR-4878 LABC and LARC Supplement.

Property evaluated:

Structural

2.0 USES

The Hilti HIT-HY 200 V3 Adhesive Anchor System is used

to anchor building components to fully grouted concrete

masonry walls. Threaded rods, Hilti HIT-Z(-R) anchor rods,

steel reinforcing bars, and internally threaded inserts

installed with Hilti HIT-HY 200 V3 can resist static, wind, and

earthquake loads, as noted in Section 4.0 of this evaluation

report. The anchor system is an alternative to Section 8.1.3

(2016 or 2013 editions) or Section 2.1.4 (2011 or 2008

editions) of TMS 402/ ACI 530/ ASCE 5, as applicable, as

referenced in Section 2107.1 of the IBC. The anchor system

may also be used where an engineered design is submitted

in accordance with Section R301.1.3 of the IRC.

3.0 DESCRIPTION

3.1 General:

The Hilti HIT-HY 200 V3 Adhesive Anchoring System is

comprised of the following components:

 Hilti HIT-HY 200 V3 adhesive packaged in foil packs

(either Hilti HIT-HY 200-A V3 or Hilti HIT-HY 200-R V3)

 Adhesive mixing and dispensing equipment

 Equipment for hole cleaning and adhesive

injection

he Hilti HIT-HY 200 V3 Adhesive Anchoring System may

be used with continuously threaded rod, Hilti HIT-Z(-R)

anchor rods, Hilti HIS-N and HIS-RN internally threaded

inserts or deformed steel reinforcing bars as depicted in

Figures 4 and 5. The primary components of the Hilti

Adhesive Anchoring System, including the Hilti HIT-HY 200

V3 Adhesive, HIT-RE-M static mixing nozzle and steel

anchoring elements, are shown in Figure 5 of this report.

The manufacturer’s printed Installation instructions (MPII),

as included with each adhesive unit package, are replicated

as Figure 6.

3.2 Materials:

3.2.1 Hilti HIT-HY 200 V3 Adhesive: Hilti HIT-HY 200 V3

Adhesive is an injectable, two-component hybrid adhesive.

The two components are separated by means of a dual-

cylinder foil pack attached to a manifold. The two

components combine and react when dispensed through a

static mixing nozzle attached to the manifold.

Hilti HIT-HY 200 V3 is available in 11.1-ounce (330 mL) and

16.9-ounce (500 mL) foil packs. The manifold attached to

each foil pack is stamped with the adhesive expiration date.

The shelf life, as indicated by the expiration date, applies to

an unopened foil pack stored in a dry, dark environment and

in accordance with Figure 6.

Hilti HIT-HY 200 V3 Adhesive is available in two options,

Hilti HIT-HY 200-A V3 and Hilti HIT-HY 200-R V3. Both

options are subject to the same technical data as set forth

in this report. Hilti HIT-HY 200-A V3 will have shorter

working times and curing times than Hilti HIT-HY 200-R V3.

The packaging for each option employs a different color

(dark grey for the plastic cap of HIT-HY 200-A V3, and light

grey for that of HIT-HY 200-R V3), which helps the user

distinguish between the two adhesives.

3.2.2 Hole Cleaning Equipment:

3.2.2.1 Standard Equipment: Standard hole cleaning

equipment, comprised of steel wire brushes and air nozzles,

is described in Figure 6 of this report.

3.2.2.2 Hilti Safe-Set™ System: The Hilti Safe-Set™ with

Hilti HIT-HY 200 V3 consists of one of the following:

 For the Hilti HIT-Z(-R) anchor rods, hole cleaning is not

required after drilling the hole.

Summary of content (15 pages)

PAGE 1
www.icc-es.org | (800) 423-6587 | (562) 699-0543 ICC-ES Evaluation Report ESR-4878 A Subsidiary of the International Code Council ® Issued November 2021 This report is subject to renewal November 2022. DIVISION: 04 00 00—MASONRY Section: 04 05 19.
PAGE 2
ESR-4878 | Most Widely Accepted and Trusted  For Threaded Steel Rods, Steel Reinforcing Bars, and Hilti HIS-N and HIS-RN Inserts, the Hilti TE-CD or TE-YD hollow carbide drill bit with a carbide drilling head conforming to ANSI B212.15 is used in conjunction with a Hilti vacuum with a minimum value for the maximum volumetric flow rate of 129 CFM (61 ℓs). The Hilti TE-CD or TE-YD drill bit will remove drilling dust, automatically cleaning the hole. 3.2.
PAGE 3
ESR-4878 | Most Widely Accepted and Trusted 4.1.4 Design of Threaded Rods and Reinforcing Bars Installed in the Top of Fully Grouted CMU Walls: Allowable tension and shear load values for 1/2- and 5/ -inch-diameter (12.7 mm and 15.9 mm) steel threaded 8 rods and No. 4 and No. 5 reinforcing bars installed in the top of grout-filled CMU walls and resisting static, wind, or earthquake loads are reported in Table 3A and Table 3B, respectively.
PAGE 4
ESR-4878 | Most Widely Accepted and Trusted 5.12 The Hilti HIT-HY 200 V3 Adhesive Anchor System may be installed in base materials having interior temperatures between 14°F (-10°C) and 104°F (40°C) for threaded rods, rebars, and Hilti HIS-(R)N inserts or between 41°F (5°C) and 104°F (40°C) for HIT-Z(-R) anchor rods at the time of installation. Installation of HIT-HY 200 V3 adhesive in base materials having temperatures beyond this range is outside the scope of this report. 5.
PAGE 5
ESR-4878 | Most Widely Accepted and Trusted Page 5 of 15 FIGURE 1—INFLUENCE OF BASE MATERIAL TEMPERATURE ON ALLOWABLE TENSION AND SHEAR LOADS FOR HILTI HIT-HY 200 V3 ADHESIVE TABLE 1A—ALLOWABLE ADHESIVE BOND TENSION LOADS FOR THREADED RODS, HIT-Z(-R) ANCHOR RODS, AND REINFORCING BARS IN THE FACE OF GROUT-FILLED CONCRETE MASONRY UNITS (POUNDS)1,2,7,8,9,11,12,13 Anchor Diameter (inches), or Rebar Size Embedment (inches)3 Load @ ccr and scr Critical, scr (inches) 13.
PAGE 6
ESR-4878 | Most Widely Accepted and Trusted Page 6 of 15 TABLE 1B—ALLOWABLE ADHESIVE BOND SHEAR LOADS FOR THREADED RODS, HIT-Z(-R) ANCHOR RODS, AND REINFORCING BARS IN THE FACE OF GROUT-FILLED CONCRETE MASONRY UNITS (POUNDS)1,2,7,8,9,10,11,12,13 Spacing4 Anchor Diameter (inches) Edge Distance5 Load Reduction Factor at cmin6 Embedm ent (inches)3 Load @ ccr and scr 3 33/8 825 1 1 4 /2 1,240 18 4 0.50 12 4 0.44 0.85 5 55/8 2,120 22.5 4 0.50 20 4 0.22 0.71 3 63/4 2,480 27 4 0.
PAGE 7
ESR-4878 | Most Widely Accepted and Trusted Page 7 of 15 TABLE 2B—ALLOWABLE ADHESVE BOND SHEAR LOADS FOR HIS-N AND HIS-RN INSERTS IN THE FACE OF GROUT-FILLED CONCRETE MASONRY UNITS (POUNDS)1,2,7,8,9,10,11,12, 13 Spacing4 Anchor Diameter (inches) Embedment (inches)3 Load @ ccr and scr Critical, scr (inches) Minimum, smin (inches) Edge Distance5 Load Reduction Factor @ smin6 Critical, ccr (inches) Minimum, cmin (inches) Load Reduction Factor @ cmin6 3 43/8 1,045 17 4 0.
PAGE 8
ESR-4878 | Most Widely Accepted and Trusted Page 8 of 15 TABLE 3B—ALLOWABLE ADHESIVE BOND TENSION AND SHEAR LOADS FOR REINFORCING BARS IN THE TOP OF GROUT-FILLED MASONRY UNITS (POUNDS)1,2,3,4,8 Reinforcing Bar Size Embedment (inches) Edge Distance5,6 (inches) No. 4 41/2 13/4 No. 5 5 13/4 5 /8 Minimu m End Distance (inches) 8 Shear Load7 Tension Load7 770 Load Parallel to Edge of Masonry Wall 605 795 720 Load Perpendicular to Edge of Masonry Wall 235 295 For SI: 1 inch = 25.4 mm, 1 lbf = 4.
PAGE 9
ESR-4878 | Most Widely Accepted and Trusted Page 9 of 15 FIGURE 2—ALLOWABLE ANCHOR INSTALLATION LOCATIONS IN THE FACE OF GROUT-FILLED CONCRETE MASONRY (ASTM C90) 1-3/4ʺ Min. Edge Distance (See load table) Min.
PAGE 10
ESR-4878 | Most Widely Accepted and Trusted Page 10 of 15 DEFORMED REINFORCMENT THREADED STEEL ROD HILTI HIT-Z AND HIT-Z(-R) ANCHOR ROD HILTI HIS-N AND HIS-RN THREADED INSERTS FIGURE 4—INSTALLATION PARAMETERS HILTI DISPENSER HILTI HIT-HY 200 V3 FOIL PACK AND MIXING NOZZLE HILTI TE-CD OR TE-YD HOLLOW CARBIDE DRILL BIT ANCHORING ELEMENTS FIGURE 5—HILTI HIT-HY 200 V3 ANCHORING SYSTEM
PAGE 11
ESR-4878 | Most Widely Accepted and Trusted FIGURE 6—MANUFACTURER’S PRINTED INSTALLATION INSTRUCTIONS (MPII) Page 11 of 15
PAGE 12
ESR-4878 | Most Widely Accepted and Trusted FIGURE 6—MANUFACTURER’S PRINTED INSTALLATION INSTRUCTIONS (MPII) (Continued) Page 12 of 15
PAGE 13
ESR-4878 | Most Widely Accepted and Trusted FIGURE 6—MANUFACTURER’S PRINTED INSTALLATION INSTRUCTIONS (MPII) (Continued) Page 13 of 15
PAGE 14
ICC-ES Evaluation Report ESR-4878 LABC and LARC Supplement Issued November 2021 This report is subject to renewal November 2022. www.icc-es.org | (800) 423-6587 | (562) 699-0543 A Subsidiary of the International Code Council ® DIVISION: 04 00 00—MASONRY Section: 04 05 19.16—Masonry Anchors REPORT HOLDER: HILTI, INC. EVALUATION SUBJECT: HILTI HIT-HY 200 V3 ADHESIVE ANCHOR SYSTEM 1.
PAGE 15
ICC-ES Evaluation Report ESR-4878 FBC Supplement Issued November 2021 This report is subject to renewal November 2022. www.icc-es.org | (800) 423-6587 | (562) 699-0543 A Subsidiary of the International Code Council ® DIVISION: 04 00 00—MASONRY Section: 04 05 19.16—Masonry Anchors REPORT HOLDER: HILTI, INC. EVALUATION SUBJECT: HILTI HIT-HY 200 V3 ADHESIVE ANCHOR SYSTEM 1.