Operating Instruction DD 250-CA
Table Of Contents
- Original operating instructions
- 1 Information about the documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Preparations at the workplace
- 5.1 DD-HD 30: Setting up the drill stand and setting the drilling angle
- 5.2 DD-HD 30: Locking the carriage on the drill stand
- 5.3 Fitting the hand wheel on the drill stand
- 5.4 Securing the drill stand with an anchor
- 5.5 Securing the drill stand by vacuum
- 5.6 DD-HD 30: Fastening the drill stand with the threaded spindle (accessory)
- 5.7 DD-HD 30: Extending the rail (accessory) on the drill stand
- 5.8 DD-HD 30: Fitting the spacer (accessory)
- 5.9 DD-HD 30: Attaching the diamond core drilling machine to the drill stand
- 5.10 Fitting the water connection (accessory)
- 5.11 installing the water collection system (accessory)
- 6 Types of work
- 6.1 Setting the depth gage (accessory)
- 6.2 Fitting the diamond core bit (BL chuck)
- 6.3 Fitting the diamond core bit with an alternative type of chuck
- 6.4 Selecting the speed
- 6.5 Portable residual current device (PRCD)
- 6.6 Operating the diamond core drilling machine
- 6.7 Switching off the diamond core drilling machine
- 6.8 DD-HD 30: Detaching the diamond core drilling machine from the drill stand
- 7 Care and maintenance
- 8 Transport and storage
- 9 Troubleshooting
- 10 Disposal
- 11 FCC statement (applicable in US) / IC statement (applicable in Canada)
- 12 Manufacturer’s warranty
- 13 Further information
- Mode d'emploi original
- 1 Indications relatives à la documentation
- 2 Sécurité
- 3 Description
- 4 Caractéristiques techniques
- 5 Préparatifs
- 5.1 DD-HD 30 : Montage de la colonne de forage et ajustement de l'angle de forage
- 5.2 DD-HD 30 : Blocage du boîtier de guidage sur la colonne de forage
- 5.3 Montage du volant à main sur la colonne de forage
- 5.4 Fixation de la colonne de forage avec bride d'ancrage
- 5.5 Fixation de la colonne de forage avec une semelle-ventouse
- 5.6 DD-HD 30 : Fixation de la colonne de forage avec broche filetée (accessoire)
- 5.7 DD-HD 30 : Rallonge de la crémaillère (accessoire) sur la colonne de forage
- 5.8 DD-HD 30 : Montage de l'entretoise (accessoire)
- 5.9 DD-HD 30 : Fixation de la carotteuse diamant sur la colonne de forage
- 5.10 Installation du raccordement d'eau (accessoire)
- 5.11 Montage du système de récupération d'eau (accessoire)
- 6 Travail
- 6.1 Réglage de la butée de profondeur (accessoire)
- 6.2 Mise en place de la couronne diamantée (porte-outil BL)
- 6.3 Montage de la couronne diamantée avec un porte-outil alternatif
- 6.4 Sélection de la vitesse de rotation
- 6.5 Disjoncteur à tension nulle PRCD
- 6.6 Maniement de la carotteuse diamant
- 6.7 Mise en arrêt de la carotteuse diamant
- 6.8 DD-HD 30 : Démontage de la carotteuse diamant de la colonne de forage
- 7 Nettoyage et entretien
- 8 Transport et entreposage
- 9 Aide au dépannage
- 10 Recyclage
- 11 Déclaration FCC (valable aux États-Unis) / Déclaration IC (valable au Canada)
- 12 Garantie constructeur
- 13 Informations complémentaires
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos técnicos
- 5 Preparación del trabajo
- 5.1 DD-HD 30: montaje del soporte y ajuste del ángulo de perforación
- 5.2 DD-HD 30: bloqueo del carro en el soporte
- 5.3 Montaje de la rueda de mano en el soporte
- 5.4 Fijación del soporte con taco
- 5.5 Fije el soporte mediante vacío
- 5.6 DD-HD 30: fijación del soporte con el husillo roscado (accesorio)
- 5.7 DD-HD 30: prolongación del raíl (accesorio) en el soporte
- 5.8 DD-HD 30: montaje del distanciador (accesorio)
- 5.9 DD-HD 30: fijación de la perforadora de diamante en el soporte
- 5.10 Instalación de la toma del agua (accesorio)
- 5.11 Montaje del sistema colector de agua (accesorio)
- 6 Procedimiento de trabajo
- 6.1 Ajuste del tope de profundidad (accesorio)
- 6.2 Montaje de corona perforadora de diamante (portaútiles BL)
- 6.3 Montaje de la corona perforadora de diamante con portaútiles alternativo
- 6.4 Selección de la velocidad
- 6.5 Interruptor de corriente de defecto PRCD
- 6.6 Uso de la perforadora de diamante
- 6.7 Desconexión de la perforadora de diamante
- 6.8 DD-HD 30: retirada de la perforadora de diamante del soporte
- 7 Cuidado y mantenimiento
- 8 Transporte y almacenamiento
- 9 Ayuda en caso de averías
- 10 Reciclaje
- 11 Indicación FCC (válida en EE. UU.) / indicación lC (válida en Canada)
- 12 Garantía del fabricante
- 13 Más información
- Manual de instruções original
- 1 Indicações sobre a documentação
- 2 Segurança
- 3 Descrição
- 4 Características técnicas
- 5 Preparação do local de trabalho
- 5.1 DD-HD 30: Montar a coluna e ajustar o ângulo de perfuração
- 5.2 DD-HD 30: Travar o patim na coluna
- 5.3 Montar o volante à coluna
- 5.4 Fixar a coluna com bucha
- 5.5 Fixar a coluna com vácuo
- 5.6 DD-HD 30: Fixar a coluna com o varão de enroscar (acessório)
- 5.7 DD-HD 30: Utilizar a extensão da guia (acessório) na coluna
- 5.8 DD-HD 30: Montar o distanciador (acessório)
- 5.9 DD-HD 30: Fixar o perfurador diamantado à coluna
- 5.10 Ligar o fornecimento de água (acessório)
- 5.11 Montar o sistema colector de água (acessório)
- 6 Trabalhar
- 6.1 Ajustar o limitador de profundidade (acessório)
- 6.2 Colocar a coroa diamantada (mandril BL)
- 6.3 Montar a coroa diamantada com porta-ferramentas alternativo
- 6.4 Seleccionar a rotação
- 6.5 Disjuntor de segurança PRCD
- 6.6 Operar o perfurador diamantado
- 6.7 Desligar o perfurador diamantado
- 6.8 DD-HD 30: Separar o perfurador diamantado da coluna
- 7 Conservação e manutenção
- 8 Transporte e armazenamento
- 9 Ajuda em caso de avarias
- 10 Reciclagem
- 11 Declaração FCC / IC
- 12 Garantia do fabricante
- 13 Mais informações
*2279864*
2279864 English 15
5.3 Fitting the hand wheel on the drill stand 6
The hand wheel may be fitted on the left-hand or on the right-hand side of the carriage.
In the case of the DDHD 30 drill stand, the hand wheel may be fitted on the carriage on two different
axes. The upper axis directly affects the carriage drive and the lower axis affects the carriage drive
with a gear reduction of 1:3.
1. Pull the black ring back to fit the hand wheel.
2. Fit the hand wheel onto the axle.
5.4 Securing the drill stand with an anchor 7
Hilti metal expansion anchors M16 (5/8") are usually suitable for fastening diamond core drilling
equipment to uncracked concrete. Under certain conditions, however, it may be necessary to use an
alternative fastening method.
Contact Hilti Technical Service if you have questions about secure fastening.
WARNING
Risk of injury due to use of wrong anchors! The machine can break loose and cause damage.
▶ Use anchors suitable for the material on which you are working and observe the anchor manufacturer’s
instructions.
1. Fit the anchor that is suitable for the corresponding base material. Select the distance according to the
base plate used.
▶ Ideal distance from the hole center for DD-HD 30: 330 mm (13 in)
2. Screw the clamping spindle (accessory) into the anchor.
3. Place the drill stand over the spindle and align it. When using the DD-HD 30 drill stand, use the hole
center indicator to help you align the drill stand. When a spacer is used, the drill stand cannot be aligned
using the hole center indicator.
4. Screw the clamping nut on to the spindle but do not tighten it.
5. Level the base plate by turning the leveling screws. Use the leveling indicators for this purpose. Take
care to ensure that the leveling screws make firm contact with the underlying surface.
6. Tighten the leveling screws evenly until the drill stand is securely fastened.
7. Check that the drill stand is secure.
5.5 Securing the drill stand by vacuum 8
DANGER
Risk of injury if the diamond core drilling machine falls !
▶ Fastening the drill stand to the ceiling only by means of the vacuum securing method is not permissible.
A heavy structural support or a threaded spindle, for example, can serve as an additional means of
fastening.
WARNING
Risk of injury if pressure is not checked !
▶ Before and during drilling, check that the pressure gage pointer remains in the green zone.
In order to use the drill stand with anchor base plate, establish a secure, flat-on-flat connection between
vacuum base plate and anchor base plate. Screw the anchor base plate securely to the vacuum base
plate. Make sure that the core bit selected for use will not damage the vacuum base plate.
If you are going to drill horizontally, use additional means of securing the diamond core drilling machine
(e. g. chain secured to anchor).
Before positioning the drill stand, check that you have sufficient space for assembly and operation.
1. Turn all the leveling screws until they project approx. 5 mm underneath the vacuum base plate.
2. Connect the vacuum connector on the vacuum base plate to the vacuum pump.