ICC ESR-2196 for Self-Drilling and Self-Piercing Screws

ManualsBrandsHilti ManualsFastenersS-MD-HWH KC Self-drilling metal screws

Table Of Contents

ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed

as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as

to any finding or other matter in this report, or as to any product covered by the report.

www.icc-es.org | (800) 423-6587 | (562) 699-0543 A Subsidiary of the International Code Council

ESR-2196 Reissued October 2021

ICC-ES Evaluation Report

This report is subject to renewal October 2023.

DIVISION: 05 00 00—METALS

Section: 05 05 23—Metal Fastenings

REPORT HOLDER:

HILTI, INC.

EVALUATION SUBJECT:

HILTI SELF-DRILLING AND SELF-PIERCING SCREWS

1.0 EVALUATION SCOPE

Compliance with the following codes:

 2018, 2015 and 2012 International Building Code

(IBC)

 2018, 2015 and 2012 International Residential Code

(IRC)

For evaluation for compliance with codes adopted by Los

Angeles Department of Building and Safety (LADBS), see

ESR-2196 LABC and LARC Supplement.

Property evaluated:

Structural

2.0 USES

The Hilti Self-drilling and Self-piercing Screws are used to

connect cold-formed steel members together. The screws

are used in engineered connections of cold-formed steel

and prescriptive connections prescribed by the code for

cold-formed steel framing.

3.0 DESCRIPTION

3.1 General:

The Hilti Self-drilling and Self-piercing Screws are tapping

screws, case-hardened from carbon steel conforming to

ASTM A510, Grades 1018 to 1022. Table 1 provides

screw designations, sizes, head styles, point styles,

drilling/piercing ranges, maximum total thickness of steel

members to be connected and coatings. Screws are

supplied in boxes of individual screws, or in collated plastic

strips. See Figures 1 through 8 for depictions of the screws

described in Sections 3.2 through 3.9, respectively.

3.2 HWH and HHWH Self-drilling Screws:

The #8, #10, #12 and

-inch Hex Washer head (HWH) self-

drilling screws and the #10, #12 and

-inch High Hex

Washer head (HHWH) self-drilling screws comply with

ASTM C1513 and SAE J78. The

-inch HWH screws have

a larger diameter than #14 screws complying with ASME

B18.6.4, and may be used where #14 self-drilling tapping

screws are specified. The screws have an electroplated zinc

coating or a proprietary coating, as indicated in Table 1.

3.3 HWH Self-piercing Screws:

The #8 and #10 HWH self-piercing screws comply with

ASTM C1513. The screws have an electroplated zinc

coating or a proprietary coating, as indicated in Table 1.

3.4 PPH Self-drilling Screws:

The #8 and #10 Phillips Pan head (PPH) self-drilling screws

comply with ASTM C1513 and SAE J78. The screws have

an electroplated zinc coating as indicated in Table 1.

3.5 PPH SD Framer Self-drilling Screws:

The #7 Phillips Pan head (PPH) SD Framer self-drilling

screws comply with the material and performance

requirements of ASTM C1513. The dimensions of the

screws comply with the manufacturer’s quality

documentation. The screws have an electroplated zinc

coating or a proprietary phosphated coating, as indicated in

Table 1.

3.6 PTH SD Framer Self-drilling Screws:

The #10 Phillips Truss head (PTH) self-drilling screws

comply with ASTM C1513 except for the number of threads

per inch. The screws have an electroplated zinc coating as

indicated in Table 1.

3.7 PPCH SD Framer Self-drilling Screws:

The #10 Phillips Pancake head (PPCH) SD Framer self-

drilling screws comply with ASTM C1513. The screws have

an electroplated zinc coating as indicated in Table 1.

3.8 TPCH SD Framer Self-drilling Screws:

The #12 Torx Pancake head (TPCH) SD Framer self-drilling

screws

comply with ASTM C1513. The screws have an

electroplated zinc coating as indicated in Table 1.

3.9 PFTH SD Framer Self-drilling Screws:

The #10 Phillips Flat Truss head (PFTH) SD Framer self-

drilling screws comply with ASTM C1513. The screws have

an electroplated zinc coating as indicated in Table 1.

3.10 Cold-formed Steel:

Cold-formed steel material must comply with Section A3 of

AISI S100 (Section A2 for the 2015 and 2012 IBC).

Summary of content (10 pages)

PAGE 1
www.icc-es.org | (800) 423-6587 | (562) 699-0543 ESR-2196 ICC-ES Evaluation Report DIVISION: 05 00 00—METALS Section: 05 05 23—Metal Fastenings REPORT HOLDER: HILTI, INC. EVALUATION SUBJECT: HILTI SELF-DRILLING AND SELF-PIERCING SCREWS 1.
PAGE 2
ESR-2196 | Most Widely Accepted and Trusted 4.0 DESIGN AND INSTALLATION 4.1 Design: 4.1.1 General: Screw thread length and point style must be selected on the basis of thickness of the fastened material and thickness of the supporting steel, respectively, based on the maximum total thickness of the steel members to be connected (see Figure 9) and drilling/piercing capacity given in Table 1.
PAGE 3
ESR-2196 | Most Widely Accepted and Trusted Page 3 of 10 7.0 IDENTIFICATION 7.2 The report holder’s contact information is the following: HILTI, INC. 7250 DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024 (800) 879-8000 www.hilti.com 7.1 Hilti Self-drilling and Self-piercing Screws are marked with an “H” on the top of the heads, as shown in Figures 1 through 8. Packages of Hilti Self-drilling and Selfpiercing Screws are labeled with the report holder’s name (Hilti, Inc.
PAGE 4
ESR-2196 | Most Widely Accepted and Trusted DESIGNATION DRILLING/ MAXIMUM NOMINAL MINIMUM NOMINAL NOMINAL DRILL PIERCING TOTAL SCREW HEAD PROTRUSION DESCRIPTION DIAMETER HEAD POINT CAPACITY THICKNESS COATING2 3 1 LENGTH STYLE LENGTH (Size - TPI) (inch) (inch) DIAMETER (Number) (MT) 3 3 (inch) (inch) (inch) Min. Max. S-MD 10-16 X 7/8 HHWH Pilot Point #10-16 0.190 S-MD 12-14 X 1 HHWH Pilot Point #12-14 0.216 S-SLC 02 M HWH #12-14 0.
PAGE 5
ESR-2196 | Most Widely Accepted and Trusted Page 5 of 10 TABLE 2—ALLOWABLE TENSILE PULL-OUT LOADS (PNOT/Ω), pounds-force1,2,3,4 Steel Fu = 45 ksi Applied Factor of Safety, Ω = 3.0 Screw Description Nominal Diameter (in.) Design thickness of member not in contact with the screw head (in.) 0.015 0.018 0.024 0.030 0.036 0.048 0.060 0.075 0.090 0.105 0.135 Self-drilling Screws for Steel-to-Steel Connections5 #7-18 0.
PAGE 6
ESR-2196 | Most Widely Accepted and Trusted Page 6 of 10 TABLE 4A—ALLOWABLE SHEAR (BEARING) CAPACITY OF STEEL-TO-STEEL CONNECTIONS USING HILTI SELF-DRILLING SCREWS, pounds-force1,2,3,4,5 Steel Fu = 45 ksi Applied Factor of Safety, Ω = 3.0 Screw Description #7-18 #8-18 Nominal Diameter (in.) 0.151 0.164 #10-12 #10-16 0.190 #10-18 #12-14 0.216 #12-24 1 /4-14 0.250 Design thickness of member in contact with screw head, (in.) Design thickness of member not in contact with the screw head (in.
PAGE 7
ESR-2196 | Most Widely Accepted and Trusted Page 7 of 10 TABLE 4B—ALLOWABLE SHEAR (BEARING) CAPACITY OF STEEL-TO-STEEL CONNECTIONS USING HILTI SELF-PIERCING SCREWS, pounds-force1,3,4,6 Steel Fu = 45 ksi Applied Factor of Safety, Ω = 3.0 Screw Description #8-18S Nominal Diameter (in.) 0.164 #10-12S 0.190 Design thickness of member in contact with screw head, (in.) Design thickness of member not in contact with the screw head (in.) 0.015 0.018 0.024 0.030 0.036 0.048 0.
PAGE 8
ESR-2196 | Most Widely Accepted and Trusted Page 8 of 10 FIGURE 1—HEX WASHER HEAD (HWH) AND HIGH HEX WASHER HEAD (HHWH) SELF-DRILLING SCREW FIGURE 2—HEX WASHER HEAD (HWH) SELF-PIERCING SCREW FIGURE 3—PHILLIPS PAN HEAD (PPH) SELF-DRILLING SCREW FIGURE 4—PHILLIPS PAN HEAD (PPH) SD FRAMER SELF-DRILLING SCREW FIGURE 5—PHILLIPS TRUSS HEAD (PTH) SD FRAMER SELF-DRILLING SCREW FIGURE 6—PHILLIPS PANCAKE HEAD (PPCH) SD FRAMER SELF-DRILLING SCREW FIGURE 7—TORX PANCAKE HEAD (TPCH) SD FRAMER SELF-DRILLING SCREW
PAGE 9
ICC-ES Evaluation Report ESR-2196 LABC and LARC Supplement Reissued October 2021 This report is subject to renewal October 2023. www.icc-es.org | (800) 423-6587 | (562) 699-0543 A Subsidiary of the International Code Council ® DIVISION: 05 00 00—METALS Section: 05 05 23—Metal Fastenings REPORT HOLDER: HILTI, INC. EVALUATION SUBJECT: HILTI SELF-DRILLING AND SELF-PIERCING SCREWS 1.
PAGE 10
ICC-ES Evaluation Report ESR-2196 FBC Supplement Reissued October 2021 This report is subject to renewal October 2023. www.icc-es.org | (800) 423-6587 | (562) 699-0543 A Subsidiary of the International Code Council ® DIVISION: 05 00 00—METALS Section: 05 05 23—Metal Fastenings REPORT HOLDER: HILTI, INC. EVALUATION SUBJECT: HILTI SELF-DRILLING AND SELF-PIERCING SCREWS 1.