Operating Instruction WSC 7.25-S (01)
Table Of Contents
- Original operating instructions
- 1 Information about the documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Use of extension cords
- 6 Operation
- 7 Care and maintenance
- 8 Disposal
- 9 Manufacturer’s warranty
- Notice d'utilisation originale
- 1 Indications relatives à la documentation
- 2 Sécurité
- 3 Description
- 4 Caractéristiques techniques
- 5 Utilisation de rallonges électriques
- 6 Utilisation
- 7 Nettoyage et entretien
- 8 Recyclage
- 9 Garantie constructeur
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos técnicos
- 5 Uso de alargadores
- 6 Manejo
- 7 Cuidado y mantenimiento
- 8 Reciclaje
- 9 Garantía del fabricante
- Manual de instruções original
- 1 Indicações sobre a documentação
- 2 Segurança
- 3 Descrição
- 4 Características técnicas
- 5 Utilização de extensões de cabo
- 6 Utilização
- 7 Conservação e manutenção
- 8 Reciclagem
- 9 Garantia do fabricante
6 English 322275
*322275*
4 Technical data
4.1 Technical data
SCW 70 WSC 7.25S
Weight in accordance with EPTA
procedure 01
5.1 kg 5.1 kg
Dimensions (L x W x H)
317 x 236 x 269 mm
(12.48 x 9.29 x 10.59 in)
317 x 236 x 269 mm
(12.48 x 9.29 x 10.59 in)
Base plate
290 x 170 mm (11.42 x 6.69 in) 290 x 170 mm (11.42 x 6.69 in)
Saw blade diameter
184 mm … 190 mm
(7.2 in … 7.5 in)
184 mm … 190 mm
(7.2 in … 7.5 in)
Saw blade disc thickness
1.1 mm … 1.5 mm
(0.04 in … 0.06 in)
1.1 mm … 1.5 mm
(0.04 in … 0.06 in)
Kerf width
1.7 mm … 2.3 mm
(0.07 in … 0.09 in)
1.7 mm … 2.3 mm
(0.07 in … 0.09 in)
Saw blade arbor size
30 mm
(1.2 in)
5/8 in
Cutting depth at 0°
0 mm … 67 mm
(0 in … 2.6 in)
0 mm … 67 mm
(0 in … 2.6 in)
Cutting depth at 45°
0 mm … 49 mm
(0 in … 1.9 in)
0 mm … 49 mm
(0 in … 1.9 in)
Cutting depth at 56°
0 mm … 38 mm
(0 in … 1.5 in)
0 mm … 38 mm
(0 in … 1.5 in)
No-load speed
5,800 /min 5,800 /min
Protection class
II II
5 Use of extension cords
WARNING
A damaged supply cord presents a hazard! Do not touch the supply cord or extension cord if damaged
while working. Disconnect the supply cord plug from the power outlet.
▶ Check the appliance’s supply cord at regular intervals and have it replaced by a qualified specialist if
found to be damaged.
• Use only extension cords of a type approved for the application and with conductors of adequate
cross-section. Otherwise the performance of the appliance may be affected and the cord may overheat.
• Regularly check the extension cord for damage.
• Replace damaged extension cords.
• When working outdoors, use only extension cords that are approved and correspondingly marked for
this application.
Recommended minimum conductor gauge (cross section) and maximum cable length with 120V
supply voltage
Extension cables AWG 16 AWG 14 AWG 12 AWG 10
Extension cable conductor gauge 1,31 mm² 2,08 mm² 3,31 mm² 5,26 mm²
Extension cable conductor gauge 2,58 kcmil 4,11 kcmil 6,53 kcmil 10,4 kcmil
Extension cable length 25 m 30 m 50 m 100 m
Extension cable length 75 ft 100 ft 150 ft 250 ft