ENVIRONMENTAL PRODUCT DECLARATION as per /ISO 14025/ and /EN 15804/ Owner of the Declaration Hilti AG Programme holder Institut Bauen und Umwelt e.V. (IBU) Publisher Institut Bauen und Umwelt e.V. (IBU) Declaration number EPD-HIL-20180151-IAA1-EN Issue date 06/12/2018 Valid to 05/12/2023 Hilti Firestop Cast-In Device (CP 680) Hilti Aktiengesellschaft www.ibu-epd.com / https://epd-online.
1. General Information Hilti Corporation Hilti Firestop Cast-In Device (CP 680) Programme holder IBU - Institut Bauen und Umwelt e.V. Panoramastr. 1 10178 Berlin Germany Owner of the declaration Hilti Aktiengesellschaft Feldkircher Strasse 100 9494 Schaan LIECHTENSTEIN Declaration number EPD-HIL-20180151-IAA1-EN Declared product / declared unit The declared product is HILTI Firestop Cast-In Device (CP 680). The declared unit refers to 1 piece Firestop Cast-In (CP 680).
The Hilti Firestop Cast-In Device is a global product (not specific for EU-market): therefore the product was qualified according to different standards (depending on performance requirements/ product application and characteristics). 2.2 - Hilti Firestop Cast-In Device - 4": CP 680 4" - M - for non-combustible penetrants CP 680 4" - P - for combustible penetrants Application 2.
use of wet-applied products/accessories (e.g. sealants to close the gaps around the device). The Hilti Firestop Cast-In Device shall always be installed in accordance with Hilti literature and with the relevant approval (/UL - Underwriters Laboratories Inc. - Listings/, /FM - Factory Mutual Research Approvals/, …); always respecting defined substrate type, penetrant types/sizes, additional accessories, etc. 2.9 Illustration: Flow diagram of the production process 2.
Water the penetrant is installed) with help of the lid, which is integrated in the product design and delivered as part of the product. The device allows penetrants to be changed retrospectively. Hilti Firestop Cast-In Device should not be exposed to water. Hilti literature and official approvals must always be considered. Mechanical destruction 2.15 In the event of a mechanical destruction of the Hilti Firestop Cast-In Device, the firestop penetration must be resealed or repaired.
4. LCA: Scenarios and additional technical information Since the information modules A1 to A3 are considered in this study, no information is provided on LCA scenarios and other technical information.
5.
6. LCA: Interpretation The dominance analysis shows that the main causes of environmental impacts and indicators can be found in information modules A1 and A3. This shows the global warming potential for material supply at approx. 52% and production at 45%, based on all information modules.
The tested product CP680 complies with the requirements of /Eurofins Indoor Air Comfort Label/, version 09/2010. In accordance with the /Eurofins Report, No G04983B/ Test conditions: Tested sample: CP 680 2" "-P". The loading of the test chamber was 1 test specimen per chamber. Test method as defined by Eurofins Indoor Air Confort Label, part 3 isolation material Test limitation: This test covered only substances that can be adsorbed on Tenax TA and that can be thermally desorbed.
pursuant to Directive 2008/98/EC of the European Parliament and of the Council) /AgBB/ The German committee for the health-related evaluation of building products: the procedure for the health-related evaluation of emissions of volatile organic compounds (VOC and SVOC) from construction products /Eurofins Indoor Air Comfort Label/ Eurofins "Indoor Air Comfort" (IAC) product certification is a tool to show compliance of a product with different low VOC emissions criteria Eurofins Report, No G04983A VOC - Att
UL Listing means that UL has tested representative samples of a product and determined that the product meets specific, defined requirements. These requirements are often based on UL's published and nationally recognized Standards for Safety FM - Factory Mutual Research - Approvals 11 Third-Party Certification which can be applied to an entire product or system, or to a single performance characteristic.
Publisher Institut Bauen und Umwelt e.V. Panoramastr. 1 10178 Berlin Germany Tel Fax Mail Web +49 (0)30 3087748- 0 +49 (0)30 3087748- 29 info@ibu-epd.com www.ibu-epd.com Programme holder Institut Bauen und Umwelt e.V. Panoramastr 1 10178 Berlin Germany Tel Fax Mail Web +49 (0)30 - 3087748- 0 +49 (0)30 – 3087748 - 29 info@ibu-epd.com www.ibu-epd.com Tel Fax Mail Web 05362 72 69 474 05362 72 69 478 bertram@fit-umwelttechnik.de www.fit-umwelttechnik.