Operating Instruction DCH 300 / DCH 300-X (01)
Table Of Contents
- Original operating instructions
- 1 Information about the documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Operation
- 5.1 General information
- 5.2 Fitting a diamond cutting disc
- 5.3 Fitting a synthetic resin-bonded fiber-reinforced cutting disc
- 5.4 Removing the cutting disc
- 5.5 Fitting the depth gauge (optional)
- 5.6 Removing the depth gauge
- 5.7 Setting the cutting depth on the depth gauge
- 5.8 Adjusting the guard
- 5.9 Connecting the water supply
- 5.10 Adjusting the water flow rate
- 5.11 Disconnecting the water supply
- 5.12 Switching on the cutter
- 5.13 Working safely with the cutter
- 5.14 Switching the cutter off
- 6 Care and maintenance
- 7 Transport and storage
- 8 Troubleshooting
- 9 Disposal
- 10 Manufacturer’s warranty
- Mode d'emploi original
- 1 Indications relatives à la documentation
- 2 Sécurité
- 3 Description
- 3.1 Vue d'ensemble du produit
- 3.2 Vue d'ensemble du produit
- 3.3 Utilisation conforme à l'usage prévu
- 3.4 Mauvaise utilisation possible
- 3.5 Régulateur électronique de limitation du courant de démarrage
- 3.6 Blocage contre toute mise en marche intempestive
- 3.7 Protection électronique contre les surcharges
- 3.8 Indicateur de maintenance
- 3.9 Butée de profondeur
- 3.10 Éléments livrés
- 4 Caractéristiques techniques
- 5 Utilisation
- 5.1 Consignes générales
- 5.2 Montage du disque à tronçonner diamanté
- 5.3 Montage des disques à tronçonner renforcés aux fibres et liés à la résine
- 5.4 Démontage du disque à tronçonner
- 5.5 Montage de la butée de profondeur (en option)
- 5.6 Démontage de la butée de profondeur
- 5.7 Réglage de la profondeur de coupe sur la butée de profondeur
- 5.8 Mise en place du carter de protection
- 5.9 Raccordement de l'arrivée d'eau
- 5.10 Réglage du débit d'eau
- 5.11 Coupure de l'alimentation en eau
- 5.12 Mise en marche de la tronçonneuse
- 5.13 Travail en toute sécurité avec la tronçonneuse
- 5.14 Mise à l'arrêt de la tronçonneuse
- 6 Nettoyage et entretien
- 7 Transport et entreposage
- 8 Aide au dépannage
- 9 Recyclage
- 10 Garantie constructeur
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 3.1 Vista general del producto
- 3.2 Vista general del producto
- 3.3 Uso conforme a las prescripciones
- 3.4 Posibles usos indebidos
- 3.5 Limitación de la corriente de arranque
- 3.6 Bloqueo de rearranque
- 3.7 Protección electrónica contra sobrecarga
- 3.8 Indicador de funcionamiento
- 3.9 Tope de profundidad
- 3.10 Suministro
- 4 Datos técnicos
- 5 Manejo
- 5.1 Indicaciones generales
- 5.2 Montaje del disco tronzador de diamante
- 5.3 Montaje del disco tronzador de aglomerado con resina sintética y reforzado con fibra
- 5.4 Desmontaje del disco tronzador
- 5.5 Montaje del tope de profundidad (opcional)
- 5.6 Desmontaje del tope de profundidad
- 5.7 Ajuste de la profundidad de corte en el tope de profundidad
- 5.8 Ajuste de la caperuza protectora
- 5.9 Conexión del suministro de agua
- 5.10 Ajuste del volumen de agua
- 5.11 Desconexión del suministro de agua
- 5.12 Conexión de la tronzadora
- 5.13 Trabajo seguro con la tronzadora
- 5.14 Desconexión de la tronzadora
- 6 Cuidado y mantenimiento
- 7 Transporte y almacenamiento
- 8 Ayuda en caso de averías
- 9 Reciclaje
- 10 Garantía del fabricante
- Manual de instruções original
- 1 Indicações sobre a documentação
- 2 Segurança
- 3 Descrição
- 3.1 Vista geral do produto
- 3.2 Vista geral do produto
- 3.3 Utilização conforme a finalidade projectada
- 3.4 Possível uso incorrecto
- 3.5 Regulação da corrente de arranque
- 3.6 Bloqueio de arranque
- 3.7 Protecção electrónica contra sobrecarga
- 3.8 Indicador de manutenção
- 3.9 Limitador de profundidade
- 3.10 Incluído no fornecimento
- 4 Características técnicas
- 5 Utilização
- 5.1 Informação geral
- 5.2 Montar o disco de corte diamantado
- 5.3 Montar disco de corte de resina sintética reforçada a fibra
- 5.4 Desmontar o disco de corte
- 5.5 Colocar o limitador de profundidade (opcional)
- 5.6 Desmontar o limitador de profundidade
- 5.7 Ajustar a profundidade de corte no limitador de profundidade
- 5.8 Ajustar o resguardo
- 5.9 Ligar o fornecimento de água
- 5.10 Ajustar a quantidade de água
- 5.11 Separar a fornecimento de água
- 5.12 Ligar o sistema de corte
- 5.13 Trabalho seguro com o sistema de corte
- 5.14 Desligar o sistema de corte
- 6 Conservação e manutenção
- 7 Transporte e armazenamento
- 8 Ajuda em caso de avarias
- 9 Reciclagem
- 10 Garantia do fabricante
12 English 2149877
*2149877*
1. Disconnect the supply cord plug from the power outlet.
2. Place the hook over the guide wheel axle.
3. Pivot the hood extension into the hood until the catch is heard to engage.
5.6 Removing the depth gauge
1. Disconnect the mains plug from the power outlet.
2. Press the catch and pivot the hood extension away from the hood.
5.7 Setting the cutting depth on the depth gauge
Conditions: The depth gauge (accessory) is fitted.
1. Press the cutting depth indicator slider and move the slider until the mark is at the desired cutting depth.
2. Release the cutting depth indicator slider.
5.8 Adjusting the guard 6
1. Unplug the supply cord from the power outlet.
2. Use the hex key to slacken the clamping screw.
3. Rotate the guard into the desired position.
4. Use the hex key to tighten the clamping screw.
5.9 Connecting the water supply
DCH 300–X
1. Connect a water hose to a water supply pipe.
The maximum permitted water supply pressure is 3 bar.
2. Close the water regulator valve to shut off the water supply to the cutter.
3. Connect the water hose to the water supply connector (proprietary system).
Regularly check hoses for damage and make sure that the maximum permissible water supply
pressure of 3 bar is not exceeded.
5.10 Adjusting the water flow rate
DCH 300–X
▶ Turn the water regulator valve until the desired water flow rate is set.
5.11 Disconnecting the water supply
DCH 300–X
1. Shut off the water supply to the cutter.
2. Disengage the coupling (proprietary system) of the hose providing the water supply to the cutter.
5.12 Switching on the cutter
1. Plug the supply cord into the power outlet.
2.
DCH 300X: Press the ON button on the PRCD.
3. Hold the tool firmly with both hands, using the front and rear grips.
4. Press the switch-on safety lock.
◁ The on/off switch is unlocked.
5. Press the on/off switch.
◁ The cutting disc begins to rotate.
6. Release the switch-on safety lock and reposition your thumb firmly round the rear grip.
Printed: 23.10.2018 | Doc-Nr: PUB / 5459266 / 000 / 00