Operating Instruction DCH 300 / DCH 300-X (01)
Table Of Contents
- Original operating instructions
- 1 Information about the documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Operation
- 5.1 General information
- 5.2 Fitting a diamond cutting disc
- 5.3 Fitting a synthetic resin-bonded fiber-reinforced cutting disc
- 5.4 Removing the cutting disc
- 5.5 Fitting the depth gauge (optional)
- 5.6 Removing the depth gauge
- 5.7 Setting the cutting depth on the depth gauge
- 5.8 Adjusting the guard
- 5.9 Connecting the water supply
- 5.10 Adjusting the water flow rate
- 5.11 Disconnecting the water supply
- 5.12 Switching on the cutter
- 5.13 Working safely with the cutter
- 5.14 Switching the cutter off
- 6 Care and maintenance
- 7 Transport and storage
- 8 Troubleshooting
- 9 Disposal
- 10 Manufacturer’s warranty
- Mode d'emploi original
- 1 Indications relatives à la documentation
- 2 Sécurité
- 3 Description
- 3.1 Vue d'ensemble du produit
- 3.2 Vue d'ensemble du produit
- 3.3 Utilisation conforme à l'usage prévu
- 3.4 Mauvaise utilisation possible
- 3.5 Régulateur électronique de limitation du courant de démarrage
- 3.6 Blocage contre toute mise en marche intempestive
- 3.7 Protection électronique contre les surcharges
- 3.8 Indicateur de maintenance
- 3.9 Butée de profondeur
- 3.10 Éléments livrés
- 4 Caractéristiques techniques
- 5 Utilisation
- 5.1 Consignes générales
- 5.2 Montage du disque à tronçonner diamanté
- 5.3 Montage des disques à tronçonner renforcés aux fibres et liés à la résine
- 5.4 Démontage du disque à tronçonner
- 5.5 Montage de la butée de profondeur (en option)
- 5.6 Démontage de la butée de profondeur
- 5.7 Réglage de la profondeur de coupe sur la butée de profondeur
- 5.8 Mise en place du carter de protection
- 5.9 Raccordement de l'arrivée d'eau
- 5.10 Réglage du débit d'eau
- 5.11 Coupure de l'alimentation en eau
- 5.12 Mise en marche de la tronçonneuse
- 5.13 Travail en toute sécurité avec la tronçonneuse
- 5.14 Mise à l'arrêt de la tronçonneuse
- 6 Nettoyage et entretien
- 7 Transport et entreposage
- 8 Aide au dépannage
- 9 Recyclage
- 10 Garantie constructeur
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 3.1 Vista general del producto
- 3.2 Vista general del producto
- 3.3 Uso conforme a las prescripciones
- 3.4 Posibles usos indebidos
- 3.5 Limitación de la corriente de arranque
- 3.6 Bloqueo de rearranque
- 3.7 Protección electrónica contra sobrecarga
- 3.8 Indicador de funcionamiento
- 3.9 Tope de profundidad
- 3.10 Suministro
- 4 Datos técnicos
- 5 Manejo
- 5.1 Indicaciones generales
- 5.2 Montaje del disco tronzador de diamante
- 5.3 Montaje del disco tronzador de aglomerado con resina sintética y reforzado con fibra
- 5.4 Desmontaje del disco tronzador
- 5.5 Montaje del tope de profundidad (opcional)
- 5.6 Desmontaje del tope de profundidad
- 5.7 Ajuste de la profundidad de corte en el tope de profundidad
- 5.8 Ajuste de la caperuza protectora
- 5.9 Conexión del suministro de agua
- 5.10 Ajuste del volumen de agua
- 5.11 Desconexión del suministro de agua
- 5.12 Conexión de la tronzadora
- 5.13 Trabajo seguro con la tronzadora
- 5.14 Desconexión de la tronzadora
- 6 Cuidado y mantenimiento
- 7 Transporte y almacenamiento
- 8 Ayuda en caso de averías
- 9 Reciclaje
- 10 Garantía del fabricante
- Manual de instruções original
- 1 Indicações sobre a documentação
- 2 Segurança
- 3 Descrição
- 3.1 Vista geral do produto
- 3.2 Vista geral do produto
- 3.3 Utilização conforme a finalidade projectada
- 3.4 Possível uso incorrecto
- 3.5 Regulação da corrente de arranque
- 3.6 Bloqueio de arranque
- 3.7 Protecção electrónica contra sobrecarga
- 3.8 Indicador de manutenção
- 3.9 Limitador de profundidade
- 3.10 Incluído no fornecimento
- 4 Características técnicas
- 5 Utilização
- 5.1 Informação geral
- 5.2 Montar o disco de corte diamantado
- 5.3 Montar disco de corte de resina sintética reforçada a fibra
- 5.4 Desmontar o disco de corte
- 5.5 Colocar o limitador de profundidade (opcional)
- 5.6 Desmontar o limitador de profundidade
- 5.7 Ajustar a profundidade de corte no limitador de profundidade
- 5.8 Ajustar o resguardo
- 5.9 Ligar o fornecimento de água
- 5.10 Ajustar a quantidade de água
- 5.11 Separar a fornecimento de água
- 5.12 Ligar o sistema de corte
- 5.13 Trabalho seguro com o sistema de corte
- 5.14 Desligar o sistema de corte
- 6 Conservação e manutenção
- 7 Transporte e armazenamento
- 8 Ajuda em caso de avarias
- 9 Reciclagem
- 10 Garantia do fabricante
2 English 2149877
*2149877*
1.3 Product-dependent symbols
1.3.1 Symbols on the product
The following symbols are used on the product:
Protection class II (double-insulated)
Diameter
Rated speed
Revolutions per minute
Alternating current
Wireless communication
Wear eye protection
1.4 Product information
Hilti products are designed for professional use and may be operated, serviced and maintained only by
trained, authorized personnel. This personnel must be informed of any particular hazards that may be
encountered. The product and its ancillary equipment can present hazards if used incorrectly by untrained
personnel or if used not in accordance with the intended use.
The type designation and serial number are stated on the rating plate.
▶ Write down the serial number in the table below. You will be required to state the product details when
contacting Hilti Service or your local Hilti organization to inquire about the product.
Product information
Diamond cutter DCH 300 | DCH 300–X
Generation 01
Serial no.
1.5 Declaration of conformity
We declare, on our sole responsibility, that the product described here complies with the applicable directives
and standards. A copy of the declaration issued by the certification department can be found at the end of
this documentation.
The technical documentation is filed and stored here:
Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany
2 Safety
2.1 General power tool safety warnings
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
▶ Keep work area clean and well lit. Cluttered or dark areas invite accidents.
▶ Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
▶ Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
Printed: 23.10.2018 | Doc-Nr: PUB / 5459266 / 000 / 00