TE 500-AVR Printed: 02.02.
Printed: 02.02.
1 Information about the documentation 1.1 • • • About this documentation Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product. Observe the safety instructions and warnings in this documentation and on the product. Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons. 1.2 Explanation of signs used 1.2.
encountered. The product and its ancillary equipment can present hazards if used incorrectly by untrained personnel or if used not in accordance with the intended use. The type designation and serial number are stated on the rating plate. ▶ Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product. Product information Breaker Generation Serial no. 1.
▶ ▶ ▶ ▶ ▶ Prevent unintentional starting. Ensure the switch is in the off‐position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach.
▶ ▶ ▶ Use a dust removal system and suitable vacuum cleaner whenever possible. Dust from materials, such as paint containing lead, some wood species, concrete/masonry/stone containing silica, and minerals as well as metal, may be harmful. Make sure that the workplace is well ventilated and, where necessary, wear a respirator appropriate for the type of dust generated. Contact with or inhalation of the dust may cause allergic reactions and/or respiratory or other diseases to the operator or bystanders.
English Printed: 02.02.
6 English Printed: 02.02.
3 Description 3.1 Overview of the product English Printed: 02.02.
@ ; = % & Chuck Function selector switch Control switch Control switch lock Side handle 3.2 ( ) + § / Knob Service indicator Lockbutton Connector on electric tool Supply cord with keyed, releasable plug connector Intended use The product described is an electrically powered breaker. It is designed for medium-duty chiseling work on masonry and concrete.
4.1.1 Using extension cords WARNING A damaged supply cord presents a hazard! Do not touch the supply cord or extension cord if damaged while working. Disconnect the supply cord plug from the power outlet. ▶ Check the appliance’s supply cord at regular intervals and have it replaced by a qualified specialist if found to be damaged. • • • • Use only extension cords of a type approved for the application and with conductors of adequate gauge (cross section).
5.1.2 Connecting the detachable supply cord CAUTION Risk of injury! Due to leakage current as a result of dirty contacts. ▶ Connect the detachable electric connector to the electric tool only when it is clean and dry and when the supply cord is unplugged from the power outlet. 1. Push the keyed, detachable electric plug connector into the socket as far as it will go, until it is heard to engage. 2. Plug the supply cord into the power outlet. 5.1.
1. Set the function selector switch to the position. 2. Rotate the chisel to the desired position. 3. Engage the function selector switch in the position. ◁ The tool is ready for use. 5.1.5 Disconnecting the detachable supply cord 5.2 Types of work 1. Unplug the supply cord from the power outlet. 2. Press the release button and pull the keyed, detachable electric plug connector out of the socket. 3. Pull the supply cord connector out of the power tool.
5.2.1 Chiseling Set the function selector switch to the ▶ 5.2.2 position. Switching sustained operation on and off When chiseling, the on/off switch can be locked in the “on” position. 1. Push the lockbutton for continuous operation forward. 2. Press the on/off switch as far as it will go. ◁ The product then runs in sustained operating mode. 3. Push the lockbutton for continuous operation back. ◁ The product switches off.
Maintenance WARNING Danger of electric shock! Improper repairs to electrical components may lead to serious injuries including burns. ▶ Repairs to the electrical section of the tool or appliance may be carried out only by trained electrical specialists. • • • 7 • • • • 8 At regular intervals, check all visible parts and the controls for signs of damage and make sure that they all function correctly. Do not operate the power tool if signs of damage are found or if parts malfunction.
Trouble or fault The chisel cannot be released from the chuck. Possible cause The chuck is not pulled back fully. Action to be taken ▶ The service indicator blinks. A fault has occurred in the tool. ▶ The service indicator lights. The carbon brushes are worn. ▶ The tool is faulty or servicing is due. ▶ 9 Pull the chuck back as far as it will go and remove the insert tool. Have the product repaired by Hilti Service. Have checked by a trained electrical specialist and replaced if necessary.
Printed: 02.02.
Printed: 02.02.
Printed: 02.02.
Hilti = registered trademark of Hilti Corp., Schaan Printed: 02.02.
