TE 1000-AVR English Printed: 19.07.
Printed: 19.07.
1 Information about the documentation 1.1 About this documentation • • • Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product. Observe the safety instructions and warnings in this documentation and on the product. Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons. 1.2 Explanation of symbols used 1.2.
▶ Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product. Product information Breaker Generation Serial no. TE 1000AVR 02 1.5 Declaration of conformity We declare, on our sole responsibility, that the product described here complies with the applicable directives and standards.
▶ ▶ ▶ Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
▶ carcinogenic such as oak and beech dust, especially in conjunction with additives for wood conditioning (chromate, wood preservative). Material containing asbestos may be handled only by specialists. Approval must be obtained from the site engineer or architect prior to beginning the work. Work on buildings and other structures may influence the statics of the structure, especially when steel reinforcing bars or load-bearing components are cut through.
3 Description 3.1 Product overview English Printed: 19.07.
@ ; = % & ( Chuck Air vents Side handle Knob On/off switch Grip ) + § / : Power level selector switch Connector on electric tool Supply cord with keyed, releasable plug connector Service indicator Power level indicator 3.2 Intended use The product described is an electrically powered breaker for heavy chiseling work. It is designed for breaking or demolishing concrete, masonry, stone and asphalt.
TE 1000AVR Weight 27.6 lb (12.5 kg) Single impact energy 26 J 4.1.1 Using extension cords WARNING A damaged supply cord presents a hazard! Do not touch the supply cord or extension cord if damaged while working. Disconnect the supply cord plug from the power outlet. ▶ • • • • Check the appliance’s supply cord at regular intervals and have it replaced by a qualified specialist if found to be damaged.
▶ Fit or adjust the side handle. Note The instructions provided with the side handle must also be observed. 5.1.2 Detachable supply cord CAUTION Risk of injury! Due to leakage current as a result of dirty contacts. ▶ ▶ Connect the detachable electric connector to the electric tool only when it is clean and dry and when the supply cord is unplugged from the power outlet. Connect / disconnect the detachable supply cord. 5.1.2.
5.1.3 Fitting the accessory tool 1. Apply a little grease to the connection end of the accessory tool. 2. Push the accessory tool into the chuck as far as it will go, turning it and applying light pressure until it engages with an audible click. ◁ The product is ready for use. Note Use only the recommended grease supplied by Hilti. Use of unsuitable grease may cause damage to the product. 5.1.
5.2 Types of work Warning! Risk of damage! ▶ ▶ Operation of the direction of rotation and/or function selector switch while the tool is running may result in damage to the tool. Do not operate this switch while the tool is running. Observe the safety instructions and warnings in this documentation and on the product. 5.2.1 Chiseling Note The chisel can be adjusted to 6 different positions (in 60° increments).
5.2.2 Setting the chiseling power ▶ Press the power level selector switch. ◁ Chiseling power can be reduced to approx. 70% by pressing the power level selector switch. Note Chiseling power can be adjusted only when the power tool is switched on and ready for use. To reselect full chiseling power, press the chiseling power level selector switch again. Switching off and then on again also causes the power tool to return to full chiseling power.
8.1 Troubleshooting Trouble or fault The power tool doesn’t start. The service indicator lights red. The service indicator blinks red. Possible cause Electronics initialization in progress (takes up to 4 seconds after plugging in). The electronic restart interlock is activated after an interruption in the electric supply. Action to be taken ▶ Switch the power tool off and then on again. Interruption in the electric supply. ▶ The generator is in sleep mode.
10 Manufacturer’s warranty ▶ Please contact your local Hilti representative if you have questions about the warranty conditions. English Printed: 19.07.
14 English Printed: 19.07.
Printed: 19.07.
Hilti = registered trademark of Hilti Corp., Schaan Printed: 19.07.
