SF BT 18A English Français Español Printed: 20.10.
1 Printed: 20.10.
2 3 4 5 Printed: 20.10.
6 Printed: 20.10.
SF BT 18A en fr es Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode d'emploi original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual de instrucciones original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printed: 20.10.
1 Information about the documentation 1.1 Explanation of signs used 1.1.1 Warnings Warnings alert persons to hazards that occur when handling or using the product. The following signal words are used in combination with a symbol: DANGER! Draws attention to imminent danger that will lead to serious personal injury or fatality. WARNING! Draws attention to a potentially dangerous situation that could lead to serious personal injury or fatality.
Generation: Serial no.: 01 2 Safety 2.1 Safety instructions The safety rules given in the following section contain all general safety rules for electric tools which, in accordance with the applicable standards, require to be listed in the operating instructions. Accordingly, some of the rules listed may not be relevant to this electric tool. 2.1.1 General power tool safety warnings WARNING Read all safety warnings and all instructions.
Power tool use and care ▶ Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. ▶ Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
▶ Observe the national health and safety requirements. Careful handling and use of batteries ▶ Do not use the battery as a power source for other unspecified appliances. ▶ Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries. ▶ Do not expose batteries to high temperatures, direct sunlight or fire. ▶ Do not disassemble, squash or incinerate batteries and do not subject them to temperatures over 80°C (176°F).
Status Meaning 1 LED blinks, the power tool is not ready for use. • 1 LED blinks, the power tool is ready for use. 4 LEDs blink, the power tool is not ready for use. • • Charge status: < 10 % The battery has overheated or is completely discharged. The power tool is overloaded or has overheated. Note Battery charge status cannot be displayed while the control switch is pressed and for up to 5 seconds after releasing the control switch.
5.3 Fitting the belt hook (optional) 5 WARNING Risk of injury! Hazard presented by a falling power tool. ▶ A falling power tool may present a risk of injury to yourself and others. Check that the belt hook is fitted securely before beginning work. Note The belt hook allows the drill to be attached to a belt worn by the operator. The belt hook can be fitted to allow attachment on the left or right side of the body. ▶ Fit the belt hook on the appropriate side of the drill. 5.
7 Transport and storage WARNING Fire hazard. Risk of short circuiting. ▶ ▶ ▶ Never store or transport Liion batteries in loose, bulk form. Remove the battery before transporting or storing the drill. Observe the nationally and internationally applicable transport regulations when shipping batteries by road, rail, sea or air. 8 Troubleshooting If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by yourself, please contact Hilti Service.
Printed: 20.10.2015 | Doc-Nr: PUB / 5252315 / 000 / 00 2127432 *2127432* Hilti = registered trademark of Hilti Corp., Schaan Pos.
