WSR 22-A English Printed: 27.07.
Printed: 27.07.
1 Information about the documentation 1.1 About this documentation • • • Read this documentation before initial operation or use. This is a is a prerequisite for safe, trouble-free handling and use of the product. Observe the safety instructions and warnings in this documentation and on the product. Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons. 1.2 Explanation of symbols used 1.2.
The type designation and serial number are printed on the type identification plate. ▶ Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product. Product information Reciprocating saw Generation: Serial no.: WSR 22A 01 2 Safety 2.1 General safety precautions for power tools ***** For internal use only ***** 27.07.2016 / 10:05:37 - H2\DOK-Projekt\System\WSR_22-A-G1\ENU\WSR
▶ tool cannot be guaranteed. If any parts are damaged, have these parts repaired before using the tool. Many accidents are caused by poorly maintained power tools. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to jam and are easier to control. Using and handling the cordless power tool ▶ Use only the specified batteries in the power tools. Use of any other batteries may present a risk of injury and fire.
▶ ▶ ▶ ***** For internal use only ***** 27.07.2016 / 10:05:37 - H2\DOK-Projekt\System\WSR_22-A-G1\ENU\WSR18-A_P3 ▶ Never cut into unknown materials and keep the line of cut above and below the workpiece free of obstacles. If the saw blade strikes an object it may cause the power tool to kick back. Apply moderate pressure and select a suitable stroke rate when using the pipe-cutting adapter (accessory), especially when cutting large-diameter pipes. This will help to prevent the power tool overheating.
5 Printed: 27.07.2016 | Doc-Nr: PUB / 5293015 / 000 / 00 ***** For internal use only ***** 27.07.2016 / 10:05:37 - H2\DOK-Projekt\System\WSR_22-A-G1\ENU\WSR18-A_P3
6 Printed: 27.07.2016 | Doc-Nr: PUB / 5293015 / 000 / 00 ***** For internal use only ***** 27.07.2016 / 10:05:37 - H2\DOK-Projekt\System\WSR_22-A-G1\ENU\WSR18-A_P3
***** For internal use only ***** 27.07.2016 / 10:05:37 - H2\DOK-Projekt\System\WSR_22-A-G1\ENU\WSR18-A_P3 3 Description 3.1 Overview of the product 7 Printed: 27.07.
@ ; = % & ( Chuck (blade holder) Control switch Safety lock Grip Battery charge status display Battery release button ) + § / : Battery Rating plate Forward gripping area (hand guard) AVR contact shoe Saw blade 3.2 Intended use The product described is a cordless reciprocating saw. It is designed for cutting wood, wood-like materials, metals and plastics. The product is designed for two-handed operation. ▶ ▶ Use only Hilti lithiumion batteries of the B 18 / B 22 series with this product.
Stroke rate Stroke Keyless chuck for standard accessory tools WSR 22A 0 /min …3,000 /min 1.1 in (28 mm) 1/2 in 5 Operation 5.1 Safe operation CAUTION Risk of injury! Inadvertent starting of the product. Remove the battery before making any adjustments to the power tool or before changing accessories. WARNING Risk of injury! Risk of kickback. ▶ Always use saw blades of adequate length. The end of the saw blade must always project beyond the workpiece over the entire blade stroke.
***** For internal use only ***** 27.07.2016 / 10:05:37 - H2\DOK-Projekt\System\WSR_22-A-G1\ENU\WSR18-A_P3 Pull the battery out of the product to the rear. ▶ 5.2 Removing the battery 1. Press the two release buttons and hold them in the pressed position. 2. Pull the battery out of the product to the rear. 5.3 Fitting the saw blade Note Use only saw blades equipped with a 1/2" connection end. 10 Printed: 27.07.
5.4 Removing the saw blade 1. 2. 3. 4. Engage the transport lock. Turn the chuck locking sleeve counterclockwise and hold it in this position. Pull the blade forward out of the chuck. Release the locking sleeve and allow it to move back to its original position. 5.5 Inserting the battery WARNING Electrical hazard! Risk of short circuiting. ▶ Before inserting the battery, check to ensure that the battery terminals and the contacts on the reciprocating saw are free from foreign objects.
Push the battery into the product from the rear as far as it will go and until it is heard to engage with a double click. ***** For internal use only ***** 27.07.2016 / 10:05:37 - H2\DOK-Projekt\System\WSR_22-A-G1\ENU\WSR18-A_P3 ▶ 5.6 Switching on 1. Disengage the transport lock. 2. Press the control switch. 5.7 Switching off WARNING Risk of injury! Caused by the saw continuing to run. ▶ ▶ Do not lift the product away from the workpiece until it has stopped completely.
Bring the forward edge of the AVR contact shoe into contact with the workpiece. Disengage the transport lock. Press the control switch. Press the forward edge of the contact shoe against the workpiece and begin the plunge action by slowly increasing the angle of attack. Note To prevent stalling, it is important that the product is running before the saw blade is brought into contact with the surface. 5.
***** For internal use only ***** 27.07.2016 / 10:05:37 - H2\DOK-Projekt\System\WSR_22-A-G1\ENU\WSR18-A_P3 1. Engage the transport lock. 2. Remove the saw blade. 3. Pull the rectangular plastic pin forward. Note It is located between the two AVR contact shoe guide pins. 4. 5. 6. 7. Pull the AVR contact shoe out. Press the rectangular plastic pin back into the original position. Grease the AVR contact shoe lightly and insert it fully in the guides. Check that the contact shoe has engaged.
6.2 Transport and storage of cordless tools Transport CAUTION Inadvertent starting during transport. Uncontrolled starting during transport may occur if the battery is fitted, thereby resulting in damage to the tool. ▶ ▶ ▶ ▶ ▶ Always remove the battery before transporting the tool. Remove the battery. Transport the tool and batteries individually packaged. Never transport batteries in bulk form (loose, unprotected). Check the tool and batteries for damage before use after long periods of transport.
8 Disposal WARNING Risk of injury. Hazards presented by improper disposal. ▶ ▶ ***** For internal use only ***** 27.07.2016 / 10:05:37 - H2\DOK-Projekt\System\WSR_22-A-G1\ENU\WSR18-A_P3 ▶ Improper disposal of the equipment may have the following consequences: The burning of plastic components generates toxic fumes which may present a health hazard. Batteries may explode if damaged or exposed to very high temperatures, causing poisoning, burns, acid burns or environmental pollution.
Printed: 27.07.
Printed: 27.07.2016 | Doc-Nr: PUB / 5293015 / 000 / 00 ** Hilti = registered trademark of Hilti Corp.
