Assembly & Installation

assembly instructions

Item No. 2374

1. Find a clear area in which you can work.

2. Unpack ﬁxture and glass from carton.

3. Carefully review instructions prior to assembly.

1. To install glass panels (2), slip them up through the open bottom of the cage (1). The

center stem that is attached to the socket cluster assembly (not shown) is on a swivel

and can be moved to aid in installing the glass - see Drawing 1.

2. Slip bottom of glass panels (2) into channel (3) in bottom of cage (1) tip top of panel

into position, and bend over clips (4) to secure glass in cage. Repeat procedure for

remaining panels of glass.

*** The construction of this ﬁxture will be accomplished by ﬁrst installing the glass,

attaching mounting hardware to the junction box, making all necessary electrical

connections, attaching the ﬁxture to the wall.

start here

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)

AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING

INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED

ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

Drawing 1 - Glass Installation

Make electrical connections from supply wire to ﬁxture lead wires. Refer to instruction

sheet (I.S. 18) and follow all instructions to make all necessary wiring connections. Then

refer back to this sheet to continue installation of this ﬁxture.

6.1.12

Drawing 2 - Fixture Mounting

1. Prepare threaded tube (C) by threading on hex nut (D) approximately 1/2”.

2. Thread tube (C) in mounting strap (A), approximately 1/4 “ - see Drawing 2.

3. Attach mounting strap (A) to junction box (J) using two screws (B) provided.

4. It will be necessary to adjust threaded tube (C). This is done by slippiing the mount-

ing hole (E) over threaded tube (C) and holding the ﬁxture against the wall. Adjust

threaded tube (C) until there is approximately 3/8” of thread showing inside the

ﬁxture. Remove ﬁxture from wall and tighten hex nut (D) against mounting bracket (A)

to secure threaded tube (C) in place.

1. To mount ﬁxture, slip center hole of backplate (E) over threaded tube (C) and hold

ﬁxture in position - see Drawing 1.

2. Thread decorative nut (F) onto end of threaded tube (C) and tighten to secure

ﬁxture.

3. Slip reﬂector (G) onto threaded tube (C).

4. To complete assembly thread barrel knob (H) onto end of threaded tube (C) and

tighten.

H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com

PAGE 1
assembly instructions Item No. 2374 s tart here 1. Find a clear area in which you can work. 2. Unpack fixture and glass from carton. Drawing 1 - Glass Installation 3. Carefully review instructions prior to assembly. 4 *** The construction of this fixture will be accomplished by first installing the glass, attaching mounting hardware to the junction box, making all necessary electrical connections, attaching the fixture to the wall. 2 1.
PAGE 2
grounding instructions SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS. Drawing 1 - Flush Mount supply wire A C Indoor Fixtures E 1 2 twist-on connectors D B fixture leads Drawing 2 - Chain Hung supply wire A C E twist-on connectors 1 B D E wiring instructions 2 fixture leads 1.