User's Manual
Table Of Contents
- Installation
- Contents
- Safety instructions
- General safety instructions
- Certified usage
- Installation site requirements
- Device casing
- Qualification requirements for personnel
- National and international safety regulations
- Grounding the device
- Lightning protection
- Requirements for connecting electrical wires
- Requirements for connecting the supply voltage
- ATEX directive 2014/34/EU – specific regulations for safe operation
- Relevant for use in explosion hazard areas (Hazardous Locations, Class I, Division 2):
- E marking
- CE marking
- LED or laser components
- FCC note
- Note for the use in the Japan
- Note for the use in Oman
- Recycling note
- About this manual
- Key
- 1 Description
- 1.1 General description
- 1.2 Device name and product code
- 1.3 Device view
- 1.4 Power supply
- 1.4.1 Supply voltage with the characteristic value C (24 V DC ... 48 V DC)
- 1.4.2 Supply voltage with the characteristic value K (60 V DC ... 250 V DC / 110 V AC ... 230 V AC, 50 Hz ... 60 Hz)
- 1.4.3 Supply voltage with the characteristic value P (Power supply only through PoE)
- 1.4.4 Supply voltage with the characteristic value W (24 V DC)
- 1.5 Ethernet ports
- 1.6 Connections for antennas
- 1.7 Display elements
- 1.8 Management interfaces
- 1.9 Signal contact
- 1.10 Reset button
- 2 Installation
- 3 Making basic settings
- 4 First login (Password change)
- 5 Obtain compliance for operation in the European Union
- 6 Configuring the transmit power
- 7 Configuring the transmit power for the 4.9 GHz band
- 8 Maintenance and service
- 9 Disassembly
- 10 Technical data
- 10.1 General technical data
- 10.2 Dimension drawings
- 10.3 Radio technology
- 10.4 Roaming
- 10.5 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN1 (Approvals 2, characteristic value M or 9)
- 10.6 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN1 for device variants with approval for the 4.9 GHz band (Approvals 2, characteristic value P)
- 10.7 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN2 for high-gain antennas (Approvals 2, characteristic value H)
- 10.8 EMC and immunity
- 10.9 Network range
- 10.10 Power consumption/power output
- 11 Scope of delivery, order numbers and accessories
- 12 Underlying technical standards
- A Further support
82
Installation BAT-F
Release
18
07/2020
Figure 6: Scope of delivery for device variants featuring Configuration with the
characteristic value 9
Accessories
Note that products recommended as accessories may have different
characteristics to those of the device, which may limit the application
range of the overall system. For example, if you add an accessory with
IP20 to a device with IP65, the degree of protection of the overall system
is reduced to IP20.
To sustain the IP65/67 suitability for your device, use the accessories with
IP65/67 properties exclusively.
The following accessory parts are not suitable for use within IP65/67
areas:
RJ45 adapters
Terminal cabel
For reliable receive power and transmission power, you require antennas
that pertain to your application case.
The "Antenna Guide" document provides an overview of the antennas
that can be used as well as the suitable antenna accessories.
The manual is available for download on the Internet: https://
www.doc.hirschmann.com
Number Article
1× Device
1 × Safety and general information sheet
1 × EU Declaration of Conformity
1 × Power supply plug, for cable diameters of 0.24 in to 0.32 in (6 mm to
8 mm; model dependent on the characteristic value of the socket)
You find power supply plugs with a larger thread here:
“Accessories” on page 82
3×per WLAN module
premounted
Transport protection cap (plastic) for N socket
1×
premounted
Protection cap (7/8", plastic) for SFP slot
1×
premounted
Protection cap (7/8", plastic) for supply voltage connection
1×
premounted
Protection cap (7/8", plastic) for supply voltage connection
1×
premounted
Protection screw (M12, plastic) for signal contact
3× or4×
premounted
(depending on the
device variant)
Protection screw (M12, plastic) for interfaces
Gigabit Ethernet SFP transceiver Order number
M-SFP-SX/LC 943 014-001
M-SFP-SX/LC-EEC 943 896-001