ATI Radeon™ HD 2600 Series User’s Guide P/N 137-41353-10
ii © 2007 Advanced Micro Devices, Inc. All rights reserved. The contents of this document are provided in connection with Advanced Micro Devices, Inc. (“AMD”) products. AMD makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice.
iii Important Safety Instructions • • • • • • • • Read Instructions—All the safety and operating instructions should be read before the product is operated. Retain Instructions—The safety and operating instructions should be retained for future reference. Heed Warnings—All warnings on the product and the operating instructions should be adhered to.
iv
v Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 System Requirements 1 Installing the Graphics Card . . . . . . . . . . . . . . . . . 3 Before You Begin Record the Serial and Part Numbers Uninstall Old Graphics Drivers Install the Graphics Card 3 3 4 5 Installing and Configuring Displays . . . . . . . . . . . 7 Connections Adapters Supported Display Connections Connecting and Configuring Displays 7 7 8 9 Installing Software and Drivers . . . . . . . . . . . . .
vi Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Troubleshooting Determine the System Card Bus Type Updating your AGP Motherboard/Chipset Drivers Reinstalling Drivers Product Registration Customer Care Additional Accessories Compliance Information 41 44 45 47 48 48 49 50 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Introduction This guide will help you get your hardware and software installed. Use the ATI Catalyst™ Control Center to access the comprehensive help system, generate a problem report, and get the software version information. System Requirements Hardware • • • • ATI CrossFire™ Requirements AMD Athlon® or Intel® Pentium® 4 512MB of system memory; 1GB or more for best performance. Optical drive for installation software (CD-ROM or DVD-ROM drive). A 550 Watt or better power supply.
2
3 Installing the Graphics Card This topic guides you through the installation of the graphics card. Before You Begin Before you begin installing the graphics card, do the following. • Record the Serial and Part Numbers on page 3. • Uninstall Old Graphics Drivers on page 4. When you have completed the above procedures, do the following: Install the Graphics Card on page 5.
4 Uninstall Old Graphics Drivers To ensure successful installation of the graphics card driver, uninstall the graphic drivers for the existing graphics card before removing the graphics card from the computer. Depending on the operating system, choose either the Windows® XP or Windows Vista™ uninstall procedure: • Uninstall old graphics drivers (Windows® XP) on page 4. • Uninstall old graphics drivers (Windows Vista™) on page 4.
5 Install the Graphics Card 1 Make sure the computer, monitor, and other peripheral devices are off. 2 Unplug the computer power cord and disconnect cables from the back of the computer. Caution! To avoid possible damage to the motherboard, wait approximately 20 seconds after unplugging the power cord before disconnecting a peripheral or removing a component from the motherboard. 3 Remove the computer cover. If necessary, consult the computer manual for help removing the cover.
6 10 Turn on the monitor and then the computer. Note: For troubleshooting information, see Reference on page 41. Note: For information on connecting monitors, see Installing and Configuring Displays on page 7. Note: If you are installing a CrossFire™ configuration, see CrossFire™ on page 35.
7 Installing and Configuring Displays Connections The following illustrate the typical connections on the ATI Radeon™ HD 2600 Series graphics card. The connections available may vary between models of this series graphics card. ATI Radeon™ HD 2600 Series Connections Legend 1 DVI-I Dual Link connection (Provides audio and video digital signals. It provides HDMI™ output that is compatible with most HDMI™ devices.
8 ATI DVI to HDMI™ Adapter The HDMI™ adapter is a proprietary adapter manufactured and sold by AMD approved manufacturers (like Wieson Technologies Co., Ltd.) that has a specific detection mechanism to allow properly configured graphics cards to pass HDMI™ signals through a DVI connection to an HDMI™ compliant device.
9 The following table shows display configurations available when ATI CrossFire™ is not enabled.
10 Configure the display 1 Navigate to the Control Panel and choose Display, or right-click on the desktop and choose Properties. 2 Choose the Settings tab and select the screen resolution and color depth that best suit your requirements and your display’s performance. 3 Click Advanced and then select the Monitor tab. 4 Choose a refresh rate from the drop-down list. Caution! Choosing a refresh rate unsupported by your display may damage your display.
11 Installing Software and Drivers Software is provided to take advantage of all the features of your ATI graphics card, including: • • • • • Graphics card driver ATI Catalyst™ Control Center HydraVision™ software (included in the Custom install) SurroundView™ software (included in the Custom install) Avivo™ video converter software (included in the Custom install) Install the software To install or remove the drivers, you must have administrator rights or be logged on as a user with administrator rights
12
13 ATI Catalyst™ Control Center The ATI Catalyst™ Control Center is software that provides access to the display features of the graphics card. Use the ATI Catalyst™ Control Center to fine-tune your graphics settings, enable or disable connected display devices, and change the orientation of the desktop. Many features display previews of the changes before they are applied.
14 Start ATI Catalyst™ Control Center Start ATI Catalyst™ Control Center from one of the following access points: Access Point Instructions Windows® Desktop 1. Right-click the Windows® desktop. Windows® Start Menu From the Windows® task bar, click Start, and then select Programs > ATI Catalyst™ Control Center. Windows® System Tray 1. Right-click the ATI icon in the Windows® System Tray.
15 Using TV Display and Capture Features These topics describe how to use the TV display and video capture features of your graphics card. • Viewing the PC’s Display on TV or HDTV on page 15. • Connecting to a TV, VCR, or HDTV on page 16. • Capturing Video on page 28. • Avivo™ Video Converter on page 31. Viewing the PC’s Display on TV or HDTV The graphics card has TV out capability. You can attach the graphics card to a TV and a monitor at the same time.
16 Viewing Text on a TV A TV is designed primarily to show moving images. The large dot pitch of a TV will yield poor quality static images. The small text sizes commonly used for PC desktops can appear blurred or unclear on a TV. You can compensate for this degradation by using larger fonts. Using a TV as the Only Display If you plan to move the computer to a place where you are using TV display only, make sure that you have the TV display feature enabled prior to disconnecting the monitor.
17 Note: For maximum performance when watching DVD movies or playing computer games on the TV, find the mode and screen resolution that provide the best result, and use those settings exclusively. This topic includes the following procedures: • Connect to an HDMI™ HDTV (DVI-to-HDMI™) on page 17. • Connect to an HDTV (DVI-to-DVI) on page 19. • Connect to an HDTV or component video device (DVI-to-Component Video using ATI DVI-to-HDTV adapter) on page 20.
18 HDMI™-to-HDMI™ connectors Legend 1 Computer 2 DVI connection on the graphics card 3 DVI-to-HDMI™ adapter 4 HDMI™-to-HDMI™ cable 5 HDMI™ connection on the HDTV 6 HDMI™ HDTV 3 Connect the DVI-to-HDMI™ adapter to the DVI connection on the graphics card. 4 Connect one end of the HDMI™-to-HDMI™ cable to the DVI-toHDMI™ adapter. Connect the other end of the HDMI™-to-HDMI™ cable to the HDMI™ connection on the HDMI™ HDTV. 5 If necessary, configure the HDTV for external audio.
19 7 Configure the HDTV using the ATI Catalyst™ Control Center, Displays Manager and DTV(HDMI) . Connect to an HDTV (DVI-to-DVI) 1 Before connecting an HDTV, attach a monitor to the computer and install the video drivers. 2 Maker sure the computer and monitor are off. DVI-to-DVI connectors Legend 1 DVI connection on the graphics card and the HDTV 2 HDTV 3 DVI-to-DVI cable 4 Computer 3 Connect one end of the DVI cable to the DVI connection on the graphics card.
20 6 Power on the monitor and HDTV, and then power on the computer. The HDTV will not display anything until Windows® starts. 7 Configure the HDTV using the ATI Catalyst™ Control Center, Displays Manager and DTV(DVI). Connect to an HDTV or component video device (DVI-to-Component Video using ATI DVI-to-HDTV adapter) 1 Before connecting an HDTV, attach a monitor to the computer and install the video drivers. 2 Make sure the computer and monitor are off.
21 3 Set the ATI HDTV Component Video Adapter DIP switches. Configure the DIP switches to set the appropriate display mode and aspect ratio. This sets the modes which appear when you select Show all Modes in the ATI Control Panel. a) Set the display mode Note: DIP switch 3 is always off (540p is not supported). Note: Set all DIP switches on that correspond to the modes the component input device supports; for further details, consult the manual for the component video input device.
22 5 Matching the colors on the connections, connect one end of the RCA patch cables to the ATI DVI-to-HDTV component video adapter. Connect the other end of the RCA patch cables to the component video connections on the HDTV. 6 Connect one end of a sound cable to the computer sound card. Connect the other end of the cable to the sound input on the HDTV. 7 If necessary, configure the HDTV for external audio. For more information, see the documentation that came with the TV.
23 S-Video to Component Video (using the ATI 9-Pin HDTV Output Cable) Legend 1 Computer 2 S-Video connection on the graphics card 3 ATI 9-Pin HDTV output cable 4 Male RCA patch cables (available from consumer electronics dealer, not to exceed 50 feet or 15 meters.) 5 Component video connection on the HDTV 6 HDTV (Set to YPbPr input. For information specific to the device, see the HDTV manual.) 3 Attach the ATI 9-Pin HDTV Output Cable to the S-Video connection on the graphics card.
24 7 Power on the monitor and HDTV, and then power on the computer. The HDTV will not display anything until Windows® starts. 8 Configure the HDTV using the ATI Catalyst™ Control Center, Displays Manager. Connect to a composite video device (S-Video-to-S-Video or Composite Video) 1 Before connecting a composite video device, attach a monitor to the computer and install the video drivers. 2 Make sure the computer and monitor are off.
25 3 Connect the S-Video connector on the composite video cable to the S-Video connection on the graphics card. Connect the other end of the composite video cable to either the S-Video or composite video connection on the composite video device. 4 Power on the monitor and composite video device, and then power on the computer. The composite video device will not display anything until Windows® starts. 5 Configure the composite video device using the ATI Catalyst™ Control Center, Displays Manager.
26 Connect to a European video device (S-Video to SCART using composite video adapter) 1 Before connecting a European video device, attach a monitor and install the video drivers. 2 Maker sure the computer and the monitor are off.
27 3 If the video device accepts PAL input, you must change the NTSC/ PAL setting on the video card to PAL. NTSC is the TV standard used in North America. PAL is the TV standard for most of Europe, Africa, Asia, Japan, South Korea, and the Philipines. Note: You can also change the NTSC/PAL settings through software using the ATI Displays control panel. For more information, see the Help for ATI Displays. a) Disconnect the monitor cable from the graphics card. b) Remove the graphics card from the computer.
28 Capturing Video Some versions of the [ProductFamily] graphics card can capture video from a camcorder, VCR, or TV. Use a video editing application to add effects, make changes, or stream the video on the Internet. The audio and video output connectors on a TV, camcorder, or VCR will be similar to those depicted in the following illustration. Use composite video out or S-Video out; S-Video out provides better results.
29 Video capture connections Legend A Composite in and out connectors B S-Video in and out connectors 1 Graphics card 2 Video in/video out cable 3 Typical video in of TV, VCR, or camcorder connections 4 Typical video out of TV, VCR, or camcorder connections
30 Connecting a media device for video capture Use a video in/video out cable to connect the S-Video connection on the graphics card to the S-Video connection on a TV, VCR, or camcorder. Capture video to a computer 1 Connect one end of the cable to the S-Video connection on the graphics card. Connect the other end of the cable to video out on the media device. Note: S-Video and composite extension cables are available from most consumer electronics dealers.
31 4 Select the Line-In volume checkbox, and then click OK. 5 If the Mute checkbox is selected, clear it to cancel muting. Display the Line Input settings (Windows Vista™) 1 In the taskbar, right-click the Volume icon, which is usually in the lower-right corner of the desktop. 2 Choose Recording Devices, select the Line In icon, and then click Properties. 3 Click the Levels tab and then drag the volume control to increase the volume. Click OK.
32 Avivo™ Video Converter Formats To create Use this Format Generic MPEG-1 video files. Standard MPEG-1 and MPEG-2 formats achieve very high compression rates and are portable to most computers. MPEG-1 Generic MPEG-2 video files. Standard MPEG-1 and MPEG-2 formats achieve very high compression rates and are portable to most computers. MPEG-2 Generic MPEG-4 video files. Standard MPEG-4 format provides good quality at low bit rates; very high compression is possible.
33 4 Click Go. The Avivo™ Video Converter Wizard opens. 5 Follow the Avivo™ Video Converter wizard instructions. Note: The Start Over button returns the wizard to the Easy Setup Wizards page. Upload video to a video iPod® 1 Start iTunes®. 2 In the File menu, select Add File to Library. 3 Navigate to the converted files and drag the converted files to iTunes®. The converted video files are added to iTunes®. 4 Connect a video capable iPod® to the computer.
34 Upload video to a Sony® PSP 1 Connect a Sony® PSP to the computer using a USB connector. 2 Switch on the Sony® PSP. 3 Using the Sony® PSP system software, navigate to the top of the Settings list and select USB Connection. The system detects a new removable disk drive. 4 Transfer the video files to the MP_ROOT\100MNV01 folder of the Memory Stick Duo™. Note: Make sure to resolve file name duplicatation before transferring the files to the Sony® PSP.
35 CrossFire™ CrossFire™ is a multi-GPU performance gaming platform, using CrossFire™-ready motherboards and CrossFire™-compatible graphics cards. CrossFire™ works with all 3D games and applications. If ATI Catalyst™ A.I. is enabled in the ATI Catalyst™ Control Center software, the optimal rendering mode available for the application is automatically selected. Performance enhancements experienced on a CrossFire™ system depend on the application or game being used.
36 For an up-to-date listing of CrossFire™ certified motherboards, see ati.amd.com/products/certification For an up-to-date listing of certified power supplies, see: ati.amd.com/certifiedpsu Install CrossFire™ cards 1 Make sure the computer, monitor, and other peripheral devices are off. 2 Unplug the computer power cord and disconnect cables from the back of the computer.
37 Proper handling of the CrossFire™ bridge interconnects a) Remove protection tags from the connectors at each end of the CrossFire™ bridge interconnects. b) Press one end of the CrossFire™ bridge interconnect onto one of the connections on one of the graphics cards. c) Press the opposite end of the CrossFire™ bridge interconnect onto corresponding connection of the second graphics card. d) Repeat steps b and c above to connect the second CrossFire™ bridge interconnect to the graphics cards.
38 CrossFire™ connections Legend 1 550 watt (or better) power supply 2 Primary graphics card 3 Secondary graphics card 4 Two CrossFire™ bridge interconnects 8 Fasten the graphics card securely. Make sure the cables are not interfering with anything inside the computer (for example, a cooling fan) and replace the computer cover. 9 Connect the monitor to the graphics card in the primary PCIe™ slot.
39 10 Reconnect any peripherals you have disconnected and plug in the computer’s power cord. 11 Power on the monitor and then the computer. Enabling CrossFire™ To take full advantage of running dual graphics cards, enable and configure CrossFire™ in the ATI Catalyst™ Control Center. Start ATI Catalyst™ Control Center Start ATI Catalyst™ Control Center from one of the following access points: Access Point Instructions Windows® Desktop 1. Right-click the Windows® desktop.
40 4 Enable ATI Catalyst™ A.I. to automatically select the preferred rendering mode for target applications. For applications that are not identified in ATI Catalyst™ A.I., or when ATI Catalyst™ A.I. is disabled, default CrossFire™ rendering modes are used. Alternatively, you can enable the Super Anti-aliasing mode in ATI Catalyst™ Control Center. Note: When CrossFire™ is enabled, only one display device is enabled.
41 Reference This topic provides information on troubleshooting, updating AGP/ motherboard chipset drivers, reinstalling drivers, where to get additional accessories, and how to register your product, plus warranty and compliance information. Troubleshooting The following troubleshooting tips may help if you experience problems. For more help, contact customer care at ati.amd.com/support or your PC manufacturer.
42 General Troubleshooting Problem Possible solution Screen defects appear • • Check if the monitor supports the resolution, horizontal (kHz) and vertical (Hz) refresh rates as required by the graphics card. Check the current resolution, refresh rate, and color depth settings in the Settings and Monitor tabs in the Display Properties dialog. Caution! Ensure that both video card and monitor support resolution and refresh rates you select.
43 CrossFire™-Specific Troubleshooting Problem Possible solution CrossFire™ is not functioning In order for CrossFire™ to function, the CrossFire™ bridge interconnects must correctly connect the CrossFire™ graphics cards. 1. Connect one end of the CrossFire™ bridge interconnect to the internal VMO connection on one of the cards. 2. Connect the other end of the CrossFire™ bridge interconnect to the corresponding internal VMO connection of the other card. 3.
44 HDTV/HDTV Adapter Troubleshooting Problem Possible solution The colors on my TV display are incorrect • Ensure that the connections between the Component Video Adapter and your HDTV are correct (Y=Green, Pb=Blue, Pr=Red). There is no display on my TV • Your TV will not display anything until Windows® starts; this may take several minutes. Ensure that the HDTV Component Video Adapter is properly connected and the TV input is correctly configured, and then restart your computer.
45 AGP and PCIe™ graphics cards and system bus connectors Legend 3 1 AGP card and AGP expansion slot 2 PCIe™ card and PCIe™ expansion slot If you have AGP connectors and the graphics card is not working correctly, you may need to update the motherboard and chipset drivers for the computer. Updating your AGP Motherboard/Chipset Drivers Note: This section applies only if you are installing an AGP graphics card.
46 • ALi GART Driver • AMD AGP Miniport • Intel VGART • VIA AGP Driver Obtain AGP drivers for your motherboard/chipset If you experience problems with the AGP chipset drivers, you may need a software update from the motherboard or chipset manufacturer. Note: Installing the wrong AGP motherboard/chipset drivers may prevent Windows® from launching successfully. Make sure that the drivers you install are designed to function correctly with the motherboard.
47 6 To determine the manufacturer, click the [AGP device name] > Driver > Driver Details.: Sample Motherboard/Chipset Manufacturers Advanced Micro Devices (AMD) www.amd.com VIA Technologies www.viaarena.com Acer Laboratories (ALI) www.ali.com.tw Silicon Integrated Systems (SIS) www.sis.com Intel Technologies support.intel.com General Motherboard/chipset information www.motherboards.
48 Product Registration To activate your warranty and obtain product support through Customer Care, register your graphics card at: ati.amd.com/online/registration Customer Care If you require further assistance with your product, the following Customer Care options are available: Service Availability Language Access Online 24/7 English, French, Spanish, Portuguese, German ati.amd.com/support or Advanced Micro Devices, Inc.
49 Service Availability Language Access Telephone Latin America / South America 7:00AM to 3:30 PM EST Spanish, Portuguese +0800-333-5277(Argentina) +0800-891-9068 (Brazil) +001800-514-3276 (Mexico) 7:00AM to 7:00PM EST English other: +1-905-882-3277 (International and/or local toll charges to Canada will apply) Customer Care will work to resolve your issue and help you to get the graphics card product up and running.
50 Compliance Information This section details the compliance information for this product. FCC Compliance Information This [ProductFamily] product complies with FCC Rules part 15. Operation is subject to the following two conditions • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
51 CE Compliance Information EMC Directive 89/336/EEC and amendments 91/263/EEC, 92/31/EEC and 93/68/EEC, Class B Digital Device EN 55022:2003/CISPR 22 Class B, Limits and Methods of Measurement of Radio Interference Characteristics Information Technology Equipment.
52
53 Index Numerics 102 part number 1080i 21 16:9 21 3D 35, 43 4:3 21 480i 21, 44 480p 21, 44 540p 21 720p 44 A Accessories 49 Adapters 3 9-Pin Cable for Video Input/Video Output 8 9-Pin HDTV output cable 23 9-pin HDTV Output Cable 8 Composite video connector 24 DVI to VGA 7 DVI-to-HDMI 8, 18 DVI-to-HDTV 8, 20 DVI-to-VGA 7 SCART 26 Add/Remove Programs 4 AGP 44 AMD Athlon 1 Anti-aliasing 40 ATI Catalyst Control Center 14 ATISETUP utility 47 Audio cables 30 Avivo Video Converter 11, 32 B Brightness 42 C Cap
54 G games TV display 16 H HDMI 8, 18 HDMI ™ 17 HDTV 17, 20 HDTV Adapter Troubleshooting 44 Help 4, 14, 49 High Definition Television (HDTV) 44 Hot key 14, 39 HydraVision 11 I Industry Canada Compliance 50 Input and output adapters displaying PC output on TV and recording on videotape 28 DVI to VGA adapter 7 iPod 31, 33 iTunes 33 M Memory Stick Duo 34 Motherboard 1, 44 N NTSC/PAL setting 27 P PAL 27 PCI Express 1, 35 PCIe 44 Pentium 1 Power supply 1, 35 Primary slot 35 Product Registration 48 R Recordi
55 Windows Vista 4, 31 Windows volume control Windows XP 30 4, 41
56
