% Please make sure to place a soft cushioned material (such as a pillow or thick piece of foam) beneath the TV screen. Lay the TV. down on a fiat cushion surface with the back side facing up. % Insert the stand cover Into the slot of TV bottom side and secure the stand to the TV with the four Screws C (M5x12). FOR ILLUSTRATION ONLY! % Every hole of the base must be fastened with screws! Installing a Wall-mount Bracket 1.
When Installing the TV Against a Wall or Enclosed Area Make sure that your TV has adequate air circulation. Allow enough space around the TV as shown below. Avoid operating the TV at temperatures below Inadequate air 41°F Install with stand Install on the wall Cr Jhigites™ TTT Tie {Boom) 4 inches 4 inches i 2% inches | : them tam oy Dion i thews o = fog i is Leave at least this much : fee feed space around the set. Leave at least this much Sines space around the set.
Viewing the Control Panel a Power indicator Remote sensor Description Light up when the power is on. Receives remote signals from the remote control. Do not put anything near the sensor, as its function may be affected. Display an on-screen menu to setup your TV's features. Select among the different input signal sources. Adjust the volume. Select the channel. Tum on the TV or put the TV In standby mode. Caution: The TV continues fo receive power even In standby mode.
Viewing the Remote Control Power nonfood — Select AY Component HDMI VGA source Zoom button Open the DTV program guide {If available) Increase volume Decrease volume Mute button Menu button A/V 4» Move Up/Down/Left/Right or adjust settings Direct channel selection Dash button Select a digital sub channel Adjust CC mode Audio select button Mono/Stereo/SAP operation Illustrations are for your reference only.
Installing Batteries in the Remote Control = Change the batteries 1. Slide the back cover to open the battery compartment of the remote control. 2. Insert two AAA size batteries. Make sure to match the and ( ) ends of the batteries with the and ( } ends indicated in the battery compartment. 3. Close the battery compartment cover. © Gently push and slide © Insert the batteries © Gently push and slide . Dispose of your batteries In a designated disposal area. Do not throw the batteries Into a fire. .
Making Connections a ANTI GABLE COMPONENT Power input < EE mam EE = JBM ove HOM HOM HMA VA VARIEGATION HEADPHONE DIGITAL _ SERVICE HDMI HDMI HDMI VGA VGA AUDIO OUT AUDIO IN Description Connect an antenna or cable TV fo this Jack. HDMI (High-Definition Multimedia Interface)provides an uncompressed, all digital audio/video Interface between this TV and any HDMI-device, such as a set-top box, Blu-ray disc player, or A/V receiver.
4 Check the jacks for position and type before making any connections. Loose connections can result in image or color problems. Make sure that all connections are tight and secure. @ Not all AV devices have the ability to connect to a TV, please refer to the user's manual of your A/V device for compatibility and connections procedure. Always unplug the power cord when connecting textual equipment. = Connecting an antenna, cable or cable/satellite box 1. Tum off the TV before connecting the antenna. 2.
= Connecting an A/V Device with Component (YP;Pg) Cable 1. Use a component cable to connect the external A/V device's component output jacks to the TV's YP,P;, jacks. Use an audio cable to connect the external A/V device's component audio jacks to the TV's AUDIO (L/R) jacks. 2. Plug the connected devices into the mains socket before switching on the TV. 3. Select the corresponding source from the TV.
= Connecting a PC with VGA Cable 1. Use a VGA cable to connect the PC's VGA output jack to the TV's VGA jack. Use an audio cable to connect the PC's audio output jack to TV's AUDIOLOGY IN jack. 2. Plug the connected devices into the mains socket before switching on the TV. 3. Select the corresponding source from the TV. TV JACK EXTERNAL DEVICES Audio Cable. A ot nudes) =. Vocable _ = : {not Included) == Primarily this uni intended for use as an LCD TV.
