INSTALLATION GUIDE Hi sense Laser TV Display Screen Before you install this product, read this guide completely and make sure you understand all of the content.
WARNING: Please follow the instructions strictly, or it may cause serious injury or even death. NOTE: Please follow the instructions strictly, or it may cause injury and product damage. ot NOTE Disclaimer: We recommend that two people load, unload and transfer this screen. The product should be installed by professional and technical personnel, and by following the installation guide. Installing the product by unqualified personnel is dangerous and may cause personal injury.
1.1 Required Tools to Install the Screen Gh aN Tape measure Stud finder Level Pencil Screwdriver with mm Hammer for concrete Phillips screwdriver Tape drill bit for stud anchors 1.2 Hardware and Parts List for Screen Mounts ® 808 ST5.5x70 Screws (x4) M3x6 Screws (x6) Hanging component (x2) Handle (x2) _ [] Ci, Bracket wands (x2) Bracket wands (x2) Velcro strips (x2) Drill bolt 8 x 60, (x4) 460mm 500mm Poly amide 8 (PAB) 1.
1.4 Prepare Your Space Check the size of your space + Width 2 2.26m + Height 2 1.8m from the installation surface to the ceiling. + For the optimal viewing experience, we recommend a minimum viewing distance of 3m from the screen. Recommended size for your TV stand We recommend that you place your Laser stand that is at about 50cm tall and wide enough to hold the TV. F100W/LTS100MHEU/DLT100-A matches Laser TV 100L9G/100L9* = [workman W2225m paper template H3=1431m — H121.
2.1 Install the Wall Mount Brackets NOTE: Make sure you have your paper template, pencil, tape and screwdriver. 1. Starting from the top of your TV stand, add 1.501m above it to get the height of the top of the paper template. Mark the height onto the wall. H and L1 may change according to the adjustment of Laser TV, the length and height is only for reference. 2. Put the paper template on the center of the wall. NOTE: The paper template should match the mark you made on the wall. 3.
IF YOU HAVE A SOLID CONCRETE OR CONCRETE BLOCK WALL NOTE: Make sure you have your concrete anchors and hammer. 4, Drill holes for the top screws. Following the vertical line on the paper template, drill holes for the bottom screws within the proposed area. 5. Remove the paper template and insert four anchors into the holes. Be sure the anchors are flush with the concrete surface. 6. Install the brackets with the screws and firmly tighten them.
3.1 Hang the Screen 1. We strongly recommend that two people handle this screen when moving it. Be sure to use gloves(included) to protect the screen from grease, sweat and dirt. 2. Check the up and down direction of the screen. To make sure the orientation of the screen is comet, check the 'UP' label on the back cover of the screen. When your Laser TV is placed on a flat surface(figure a), the screen should be installed in its normal direction and the arrow of 'UP’ label points up{figure b).
3. Split the release paper on one side of the Velcro strips. Paste the Velcro strips on the left and right side of the bottom of the screen(on the back side of the screen). 4. Place the screen onto the brackets. NOTE: We do not recommend mounting the TV to the ceiling. However if you choose to, then the orientation of the screen will need to be reversed. 5. Make sure the screen is horizontally and vertically level.
Ad|Just the Height of the Screen Attach the handles of the wands on the wall-mount brackets and adjust the height of the screen. Refer to the top border to match the screen to the display image. WARNING: Do not look directly at the lens when this device is on because the laser light may damage your ayes! If the screen is higher than the image, then rotate the wands clockwise and move the screen down. If the screen is lower than the mag, then rotate the wands counterclockwise and move the screen up.
