Read the manual carefully and ensure you have fully understood its contents before operating this device for the first time.
Read the manual carefully and ensure you have fully understood its contents before operating this device for the first time.
Important Safety Instructions ▐ Important Notice Paragraphs beginning with the symbol conditions for the following settings. indicate important instructions, tips or For your own safety and the optimal performance of your TV, ensure to read the safety instructions before performing any installation. It is not guarantee operation and performance of peripheral devices made by other manufacturers.
Important Safety Instructions The intended use and ambient conditions for this TV This TV is intended for the rendering of video and audio signals, on a table-top or wallmounted, in a home or office environment. It must not be used in rooms with a high level of humidity or dust concentration. The warranty is only valid if used as intended by the manufacturer. WARNING High humidity and dust concentration may lead to current leaks in the device.
Important Safety Instructions Moving/Transportation Power plug and power cable Before moving this TV, disconnect all cables and move in the vertical position only. Grasp the device on the upper and lower edges of the frame. - Do not touch the power plug with wet hands. - Do not place heavy objects on the power cable. Route the cable so that it is not kinked or laid over sharp edges, walked on or exposed to chemicals. A power cable with damaged insulation can cause electric shock and fire.
Important Safety Instructions Air ventilation and high temperatures Prevent small items from getting into the interior of the device through the ventilation slots. Such objects may cause short circuits, which may cause fire. Install your TV only where there is proper ventilation, and ensure that there is at least 10 cm free space on the sides and 20 cm above the unit for air circulation. Excessive heat and obstruction of ventilation could lead to fire or early failure of some electric components.
Important Safety Instructions If you have a cardiac pacemaker, keep a distance of at least 22 cm from the TV. Radio waves may interfere with the operation of a pacemaker. Supervision - Do not let children play unsupervised close to the TV. It could tip over, be pushed off or pulled down from the stand surface and injure someone. Built-in wireless LAN - Do not allow a switched-on TV to run unattended. - Do not connect to wireless networks that you do not have the usage rights for.
Important Safety Instructions Cleaning and care swallowed. If swallowed by mistake, force the patient to vomit and visit the nearest hospital. CAUTION: Unplug the power cord prior to cleaning the TV. Clean the TV, the screen, and the remote control with a soft, moist, clean and color-natural cloth only. Do not use any chemicals. Modification Do not attempt to modify this product in any way. Unauthorized modification could void the warranty of this unit, cause electric shock and fires.
Contents Product image is only for reference, actual product may vary in appearance. Parts of the software function changes with the system upgrade. Contents Accessories List..............................................................................................................1 Installing the Stand or Wall mount bracket .....................................................................2 TV Front.......................................................................................................
Installing the Stand or Wall mount bracket Installing the Stand CAUTION Be sure to disconnect the A/C power cord before installing a stand or Wall-Mount brackets. The screen display is very fragile, and must be protected at all times when installing the base stand. Be sure that no hard or sharp object, or anything that could scratch or damage the screen display, comes into contact with it. DO NOT exert pressure on the front of the TV at any time because the screen could crack.
Installing the Stand or Wall mount bracket 65" Attention: According to the size of the TV supporting surface, you can select one of the base stand installation patterns, as shown in the figure. Base Stand Base Stand Screws： （M5×12) × 4 Screws： （M5×12) × 4 Base Stand Base Stand Installing the wall mount bracket Wall mount hole pattern (mm) 200 × 200 （43"） 200 × 300 （50"/55"） 300 × 200 （65"） Wall mount screw size (mm) M6 8.0-10.0 mm(50"/55") 9.5 -11.
TV Front TV Front Single button (Remote sensor / Power indicator / Standby) Item Description Remote sensor Receive remote signals from the remote control. Do not put anything near the sensor, as its function may be affected. Power indicator The light is red in standby mode. Press the single button when in standby mode, TV will be turned on.
TV Rear TV Rear CARD FACE FRONT ARC HDMI 1 (4K@60Hz) COMMON INTERFACE AV IN ANT 2 DVB-S/S2 ANT 1 DVB-T/T2/C 43"/50"/55" 0.5A(MAX) × 2 DIGITAL AUDIO OUT Before connecting external equipment, remove the mains plug from the wall socket. Otherwise, it may cause electric shock. DC 5V Not all A/V devices have the ability to connect to a TV, please refer to the user’s manual of your A/V device for compatibility and connections procedure.
TV Rear ANT 1 DVB-T/T2/C 65" ARC DC 5V USB 2 LAN NOTES ANT2 Jack supports power supply for satellite antenna (13/18V, 0.5A max.) Check the jacks for position and type before making any connections. Loose connections can result in image or color problems. Make sure that all connections are tight and secure. Not all A/V devices have the ability to connect to a TV, please refer to the user’s manual of your A/V device for compatibility and connections procedure.
Making Connections LAN (Wired setup) Connect your TV to your network by connecting the LAN port on the back of your TV to an external modem or router using a LAN (Ethernet/Cat 5) cable. See the illustration below. · We recommend to use a modem or router that supports Dynamic Host Configuration Protocol (DHCP). Modems and routers that support DHCP automatically provide the IP address, subnet mask, gateway, and DNS, so you don’t have to enter them manually. Most home networks already have DHCP.
Making Connections Outdoor Antenna Cable or ANT OUT ANT 1 DVB-T/T2/C (not included) Antenna Cable (75Ω) VHF/UHF Antenna ANT ANT 2 DVB-S/S2 (not included) Satellite antenna Audio Amplifier/Speaker DIGITAL AUDIO OUT HDMI (ARC) DIGITAL AUDIO OUT DIGITAL AUDIO cable (not included) Audio Amplifier/Speaker HDMI HDMI HDMI cable (not included) ARC HDMI DVD/Blu-Ray/AV receiver/ Set-top Box HDMI HDMI HDMI HDMI cable (not included) Red(R) (not included) White(L) AV IN VCR/DVD Player/ Recorder
Making Connections 2 1 CAM CARD COMMON INTERFACE SMART CARD NOTES Before you insert/remove the CI+ module, ensure that the TV is switched off. Then insert the CI card into the CI+ module in accordance with the Service Provider’s instructions. Do not repeatedly insert or remove the Common Access Module as this may damage the interface and cause a malfunction. You must obtain a CI+ module and card from the service provider of the channels you want to watch.
Remote Control 1 2 3 4 5 6 7 1 POWER: Switch the TV on or into standby mode 2 INPUT: Select input sources 3 Number button: Direct channel selection or numbers input 4 GUIDE: Display the Electronic Program Guide (DTV mode) 5 Subtitle: Activate or deactivate the subtitle mode 6 Special function buttons 7 Display the Quick setup menu 8 TXT: Turn on/off the teletext function 9 / / < / >: Allows you to navigate the OSD menus and adjust the system settings to your preference 10 OK: Confi
Remote Control 1 2 3 4 5 1 POWER: Switch the TV on or into standby mode 2 INPUT: Select input sources 3 Number button: Direct channel selection or numbers input 4 T.
Remote Control Installing Batteries in the Remote Control 1. Slide the back cover to open the battery compartment of the remote control. 2. Insert two AAA size batteries. Make sure to match the (+) and ( - ) ends of the batteries with the (+) and ( - ) ends indicated in the battery compartment. 3. Close the battery compartment with the cover. NOTES Product image is only for reference, actual product may vary in appearance.
Turning the TV on for the First Time Turning the TV on for the First Time 1. Connect the mains cable to the mains socket after you have completed all the connections. 2. The first time you turn the TV on, it will go straight into the Installation Guide. 3. Press the [ / / < / >] buttons to navigate the menu and change the settings. Press the [OK] button to confirm. Language Select your desired language to be displayed on the menu. Country Select the Country where you will operate the TV.
Specifications Features, appearance and specifications are subject to change without notice. 43" 50" Without Stand 37.8 × 22.0 × 3.3 inches (961 × 560 × 83 mm) 43.9 × 25.5 × 3.2 inches (1116 × 648 × 82 mm) With Stand 37.8 × 24.1 × 7.7 inches (961 × 613 × 196 mm) 43.9 × 27.9 × 8.9 inches (1116 × 709 × 226 mm) Without Stand 15.0 lbs (6.8 kg) 21.6 lbs (9.8 kg) With Stand 15.2 lbs (6.9 kg) 21.8 lbs (9.
Specifications 55" 65" Without Stand 48.4 × 28.0 × 3.4 inches (1230 × 712 × 86 mm) 57.0 × 32.8 × 3.2 inches (1448 × 834 × 81 mm) With Stand 48.4 × 30.4 × 8.9 inches (1230 × 773 × 226 mm) 57.0 × 35.2 × 11.4 inches (1448 × 894 × 290 mm) Without Stand 27.1 lbs (12.3 kg) 36.8 lbs (16.7 kg) With Stand 27.8 lbs (12.6 kg) 37.5 lbs (17.
Other Information Recycling/Licenses WEEE (Waste Electronic Electric Equipment) European Directive 2012/19/EU This symbol on the product or on its packaging indicates that this product must not be disposed of with your household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.
