Quick Start Guide

ManualsBrandsHisense ManualsRoom Air ConditionersAP12CR1G

The window installation kit allows

you to install the air conditioner in

most vertical-sliding windows 18’’

to 50’’ wide,or horizontal-sliding

windows from 18’’ to 50’’ high.

Install Exhaust Hose and

Adapter

Attach the coupling to the

ﬂexible exhaust hose. Turn

counter-clockwise until se-

curely locked into place.

Attach the window exhaust

adapter to the ﬂexible

exhaust hose. Turn count-

er-clockwise until securely

locked into place.

Connect The Hose To The

Air Conditioner

Insert the coupling into the

slot on the back of the air con-

ditioner. Slide down to lock the

hose into place.

Connect The Hose To The

Window

Roll the air conditioner to

selected location. Attach the

window exhaust adapter to the

outer slider section (the piece

with the large exhaust hole).

Install Window

Electrical Shock Hazard

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

Failure to follow these instructions can result in

death, ﬁre, or electrical shock.

18’’ to 50’’

panel A (18”)

panel C (17”)

panel B (9”)

panel D (17”)

Cut the adhesive foam

seal to the proper length,

and attach it to the

window sash and frame.

Insert the vent panel

assembly, including ex-

tension panels, if needed,

into the window opening.

Extend the extension

panels, if used.

Cut the Non-adhesive foam seal

to the window width. Stu the

foam seal between the glass and

the window to prevent air and in-

sects from getting into the room.

Install the Window-lock bracket

with wood screws as shown, if

you need.

Suitable Windows

Connect it together

Choose the right panel

adhesive foam seal

use longer ones

use shorter

ones

vent panel

extension panel

Non-adhesive

foam seal

window-lock bracket

wood screw

See the user manual for detailed instruction on

installation and using the features and settings of the

air conditioner and remote control.

For questions about features, operation/performance, parts or service,

Call: 1-877-465-3566

Monday to Friday: 9:00 a.m . – 6:00 p.m. (EST) or Visit: www.hisense-usa.com

Plug In the Unit

Be sure to use a

grounded 3 prong

outlet. Do not use an

extension cord. Plug

in the unit.

Turn The Unit On

Turn the air conditioner

on, and set the desired

mode and temperature.

outer slider section

window exhaust adapter

coupling

rivets (2)

rivet

wood screws(4)

outer slider section with vent

outer slider section

Phillips screwdriver

Pencil

Scissors

inner slider section-short

Drain hose clip (Heat pump

models)

Drain hose

(Heat pump models)

inner slider section

window-lock bracket(2)

window exhaust adapter

ﬂexible exhaust hose

23⁵⁄₈” – 64¹⁄₈”

To ensure proper

ventilation

Panel

window

A 18” B 9” C 17” D 17”

18” √

19”–26” √ √

27”–34” √ √

35”–50” √ √ √

18’’ to 50’’

Before beginning, check that all parts are

included in the parts package.

non-adhesive foam seal

adhesive foam seal (2)

Tools needed

Keep unit upright at least 2 hours

prior to use.

Portable Air Conditioner

1. Uncover the primary drain port.

2. Attach the drain hose to the prima-

ry drain hose. Make sure the connec-

tor does not have a water leak.

3. Place the other end of drain hose

into a drain. Check to see that the

hose lies ﬂat and is in the drain. Make

sure the hose end that goes to the

drain is on a lower level than the hose

end that connects to the unit. The

hose should not be kinked or pinched.

A. Primary drain hole

B. Primary drain port

C. Drain hose

Draining the Air Conditioner (Heat Pump models only)

step

Parts Package

coupling

The ﬁgures in this manual are based on the external view of a standard model. They may dier from

that of the air conditioner you have selected.

If your window

length requires more

than 2 panels, after

adjust the length,

please secure the

panels with rivets.