SAFETY INFORMATION EMERGENCY DOOR OPENING INSTALLATION GUIDE
SAFETY INFORMATION 1. The manufacturer reserves the right for any modifications on the product which might be deemed necessary or useful without informing about it in this IFU. 2. Before operating your new washing machine, please read this instruction carefully, and keep it for future reference. If you have lost it accidentally, ask customer service for ecopy or hard copy. 3. Please make sure the socket is grounded securely, the water source connection is reliable. 4.
9. For appliances with ventilation openings in the base, that a carpet must not obstruct the openings. 10. Children of less than 3 years should be kept away unless continuously supervised. 11. The maximum permissible inlet water pressure, 1 MPa, for appliances intended to be connected to the water mains. The minimum permissible inlet water pressure, 0.1 MPa, if this is necessary for the correct operation of the appliance. 12. The maximum washing capacity is 7.5/8.5/9.5/10kg. 13.
ensure 2. Remove transport bolts Important: Transport bolts which are not removed can cause damage to the appliance. Screw off all transportation bolts for approx. 30mm with wrench following the direction of arrow shown (not fully screw it off). 30 Push four transportation bolts on horizontal direction inward and loose transportation bolt.
Pull out transportation bolt together with rubber part and plastic part. To ensure safety and reduce noise, you should install the transportation bolt cover supplied with the unit (see the annex accompanying the unit). Lean and place the transportation bolt into hole and press it following the shown direction until it clicks. 3. Adjustment of the feet The appliance must be installed on a solid and level floor surface (if necessry use a spirit level).
4. Install bottom cover To realize quieter operation, a bottom cover is supplied with the unit (only applies to some of the Hisense washers). After installing the cover at the bottom of the washer, the noise level will be greatly reduced. Please ask for advice from specialists before installing the cover, nevertheless, the machine can be used without the bottom cover. Noise-Reduction Bottom Plate Installation Instructions A: Stick acoustic wool to the side of bottom cover plate with the letter of “PUMP”.
B: Rig ht- an gle imp Before installing the noise-reduction bottom plate, align and paste the acoustic absorption wool with and along the right-angle impression on bottom plate (this procedure is unnecessary for some of the models without acoustic absorption wool). ress ion Pump Incline the machine to an angle of 40° and let the side with right-angle notch face towards front of the washing machine, as shown in the figure.
6. Connect the drain hose In case the drain hose is installed as shown below: Unhook it only from the right clip (see arrow) Connect the drain hose to the Drain or hook it over the edge of a sink by means of the "U" bend. Fit the “U” bend show in E, if not already installed, if it at the end of the drain hose. Ensure that there are no kinks in the drain hose. Secure the hose so that it cannot fall down. After wash phase, machine will drain out hot water. Small hand basins are not suitable.
7.
that The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead it shall be handed over to the applicable collection point for there cyclingof electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal.
Clean the outside of the washing machine with a damp cloth. Do not use abrasive detergents. Never open the door forcibly or use it as a step. DESCRIPTION OF THE WASHING MACHINE Control panel layout and appearance will depend on the model. EMERGENCY DOOR OPENING In case of failure to open the door due to power outage or other special circumstances, the door lock lever at the drainage pump door can be used for emergency opening. Note: 1. Do not operate when the machine is working normally; 2.
BEFORE THE FIRST WASH CYCLE To remove any residual water used during testing by the manufacture r, we recommend that you carry out a short wash cycle without laundry. 1 Open the tap. 2 Close the door. 3 Pour a little detergent (about 30 ml) into the main wash chamber of the deter- gent dispenser . 4 Select and start a short programme (see separate quick reference guide). PREPARATION OF THE WASHING 1. Sort the laundry according to...
Dyeing Loading the laundry Open the door. .
"A or B" / soak B A 13
unds Press the release lever in the main wash compartment downward and remove the drawer(fig.“B or D”). Remove siphon in softener slot. (fig.“C or E”). Refit the siphon in the detergent drawer and fit the drawer back inside its housing.
We recommend that you check and clean the filter regularly, at least two or three times a year. if it fails to perform spin cycles. Ensure that the water has 1 2 3 Insert removal tool like slotted screwdriver into the small opening of bottom baffle, press the bottom baffle downward with much strength and open it. Put a flat container under filter door and then drain with emergency drain pipe (see [draining residual water] for specific operation methods).
Check the supply hose regularly for brittleness and cracks and replace it if necessary using a new hose of the same type(available from After-Sales Service or specialist dealer).
solv too 17
remove some 18
Hot / Cold fill fault - For Models with Dual Inlets If you wish to connect hot and cold water supply (Fig.1): 1. Fix the red marked inlet hose to the hot water tap and to the inlet valve with the red filter on the rear side of machine. 2. Fix the other inlet hose to the cold water tap and to the inlet valve with the blue filter on the rear side of the machine. Make sure: a) The connections are tightly fixed b) Do not invert their position (for example: cold fill into hot inlet valve and vice versa).
Fault Code List Displayed on Display Window Fault Description “F01” Water inflow fault “F03” Drainage fault “F13” Door lock fault “F14” Door unlock fault “F24” Overflow or too much foam. else fault code, “F04-F98” Electronic module fault. “Unb” Unbalance alarm a. “F01” displayed on screen The machine is not fed with water or insufficient water. Check: Faucet is fully open and has enough water pressure. Water inlet pipe is knotted or not.
C. Fault code The washer stops when the program is running. The display window shows fault code “F13”, “F14”, “F24”, else fault codes from “F04” to “F98” or “Unb”. If fault code “F13” is shown Door lock is abnormal. Start program for 20 sec and unlock the washer door (PTC) to check whether the door is closed. Open or close it again. After fault is removed, press “Start/Pause” key. If fault occurs again, disconnect power supply and contact after-sale service. If fault code “F14” is shown Door open fault.
kg F 22
Instruction for use, installation guide, warranty card (depends on model) B Wrench C D E F Bottom cover(depends on model) 23
2256485-X08061280A
