Manual
REAR PANEL JACKS
(_ Antenna Input (36CX39B and 32CX39B models)
The VHF/UHF terminal can be used for normal TV, cable TV (CATV). video game, etc,
Antenna Inputs (36/32UX59B and 36/32FX49B models)
The remote control allows you to switch between two separate 75-Ohm RF antenna inputs, ANT A and ANT B. ANT A input can be
displayed as a main picture or sub-picture. ANT B can only be displayed as a main picture. (ANT B cannot be displayed as a
sub-picture). The antenna output labeled "TO CONVERTER" allows ANT A connection to pass directly to a different source such
as a cable box.
(_) AudioNideo Inputs
The INPUT button will step through each video source and antenna source input each time it is pressed, Use the audio and video
inputs to connect external devices, such as VCRs, camcorders, laserdisc players, etc. (If you have mono sound, insert the audio
cable into the left channel jack).
(_) Y-CB-CR Input: 2 (36UX59B and 32UX59B models)
This input provides Y-CB-CR jacks for connecting equipment with this capability, such as a DVD Player,
I NOTE: 36/32FX49B and 36/32CX39B models do not have Y CB-CR Inputs_ ]
I
(_ Audio to HI-FI
These jacks provide variable audio output to a separate stereo amplifier. With this connection, the audio to the stereo can be
controlled by the television's main volume. Use these jacks for the SURROUND Left and Right channels. (See page 23)
S-Video
Inputs 1, 2 for 36/32UX59B and 36/32FX49B models and Input 1 for 36t32CX39B models provide S-Video jacks for connecting
equipment with S-Video output capability.
_6_ Geomagnetism Correction (36" models)
The effects of geomagnetism may cause an uneven (partially) colored picture depending on the direction the TV is facing. Adjust
the TV as follows for best performance:
1. Turn the Power "Off'.
2. Decide on tile installation position and direction of the TV. Check the direction the TV is facing at this time.
3, Set the DIRECTION and STRENGTH switches (on back of the TV) according to the direction of the screen as shown in the
table.
TV
WEAK 1
DIRECTION ......................Sou!hea.st _ EfW ...............,_b_ .........
South I S STRONG
West ENV WEAK
Northwest *E_nJV WEAK
If the Screen is facing a Northerly direction, set to 'N'
if the Screen is facing a Southerly direction, set to ' S'
4. After setting the switches, place the TV in the decided location,
5. After relocating the TV, turn the power "ON" and check to make sure that the screen color (especially at the corners) is even_
Depending on the installation location (especially where it is susceptible to geomagnetism, for example, in a reinforced concrete
building), in this case, set the DIRECTION and STRENGTH switches to set the optimum picture.
6. In certain areas, if the screen points North or South, color unevenness may be reduced when the STRENGTH switch is set to
STRONG rather than WEAK.
I NOTE: If you move your TV, the DIRECTION and STRENGTH switches may need to be reset, I
TIPS ON REAR PANEL CONNECTIONS
The S-Video connections are provided for high performance laserdisc players, VCRs etc. that have this feature, Use these
connections in place of the standard video connection if your device has this feature.
COMPONENT: Y-CBCR connections are provided for high performance components, such as DVD players. Use these
connections in place of the standard video connection if your device has this feature.
When using the Y-CBCR input jacks, connect your components audio output to the TV's Input 2 Left and Right Audio input jacks.
If your device has only one audio output (mono sound), connect it to the left audio jack on the television.
Refer to the operating guide of your other electronic equipment for additional information on connecting your hook_up cables.
15