LCD REAR PROJECTION TELEVISION Operating Guide for 50C10, 50C10E IMPORTANT SAFETY INSTRUCTIONS ................................................................................ 2-3 FIRST TIME USE .................................................................................................................. 4-19 THE REMOTE CONTROL .................................................................................................. 20-31 ON-SCREEN DISPLAY.......................................................
IMPORTANT SAFETY INSTRUCTIONS SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI LCD REAR PROJECTION TELEVISION Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions. Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you.
IMPORTANT SAFETY INSTRUCTIONS 15. Televisions are designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the front, or top, of the cabinet which could cause the product to overturn resulting in product damage and/or personal injury. 16. Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer. 17. An outdoor antenna should not be located in the vicinity of overhead power lines or other electrical circuits.
ACCESSORIES Check to make sure you have the following accessories before disposing of the packing material. FIRST TIME USE REMOTE CONTROL BATTERIES (“AA”) POWER TV CBL/SAT DVD/VCR SWAP PIP MODE PIP SURF FREEZE MENU DAY/NIGHT SELECT MUTE LAST CH EXIT VOL CH 1 2 4 5 7 8 9 ANT 0 INFO VID1 VID2 REC 3 6 VID3 VID4 ASPECT SLEEP VID5 CLU-4329UG 1. 2.
HOW TO SET UP YOUR NEW HITACHI LCD REAR PTV ANTENNA LOCATION Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure that the location selected allows a free flow of air to and from the perforated back cover of the set. To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can become excessively hot, for example, in direct sunlight or near a heating appliance, etc.
HOOK-UP CABLES AND CONNECTORS FIRST TIME USE Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell audio/video products. Below are illustrations and names of common connectors.
FRONT PANEL CONTROLS PUSH PUSH INPUT 5 AUDIO S-VIDEO VIDEO L/MONO VOL- R VOL+ CH- CH+ INPUT MENU EXIT SELECT CURSOR MENU/SELECT button This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote. This button also serves as the SELECT button when in MENU mode. INPUT/EXIT button Press this button to select the current antenna source, VIDEO: 1, 2, 3, 4, 5 or alternate antenna source.
FRONT PANEL CONTROLS FIRST TIME USE IR RECEIVER The screen area also acts as the IR receiver (remote sensor) of the TV. When using the remote control, point it towards the screen for best response. POWER button Press this button to turn the TV on or off. POWER light This light is on during normal operation. Light Blinking Slowly (2 seconds): television lamp is cooling down. It takes 12-15 seconds to warm up and about 2 minutes to cool NOTES: 1.
FRONT PANEL JACKS AND CONNECTORS The front panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following examples: S-VIDEO NOTE: INPUT 5 AUDIO VIDEO L/MONO R S-VIDEO AUDIO VIDEO L/MONO R 1. Completely insert connection cord plugs when connecting to front panel jacks. If you do not, the played back picture may be abnormal. 2. If you have a S-VHS VCR, use the S-INPUT cable in place of the standard video cable. 3.
REAR PANEL JACKS FIRST TIME USE DVI-HDTV ANT A TO CONVERTER PR PB R (MONO)/L PR PB R (MONO)/L Y INPUT 1 AUDIO ANT B INPUT 2 Y/VIDEO AUDIO CENTER IN (MONO)/L VIDEO S-VIDEO R (MONO)/L VIDEO S-VIDEO INPUT 4 L L R VIDEO S-VIDEO MONITOR OUT R R INPUT 3 AUDIO TO HI-FI AUDIO Antenna Input/Output ANT A- A 75-Ohm RF antenna or CATV (Cable TV) input. ANT A can be displayed as a main picture or sub-picture. ANT B- A 75-Ohm RF antenna or CATV (Cable TV) input.
REAR PANEL JACKS Component: Y-PBPR Inputs NOTES: 1. Do not connect composite VIDEO and S-VIDEO to Input 3, 4 or 5 at the same time. S-VIDEO has priority over VIDEO input. 2. Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV’s PB input and the components R-Y output to the TV’s PR input. 3. Your component outputs may be labeled Y-CBCR.
REAR PANEL CONNECTIONS FIRST TIME USE TYPICAL FULL-FEATURE SETUP D-VHS Outside antenna or cable TV coaxial cable DIGITAL OUTPUT L R OUTPUT DVD Player 2-Way signal splitter Y HDTV Set-Top Box OUTPUT PB/CB PR/CR L R Y PB PR OUTPUT L R VCR #1 DVI-HDTV ANT A PR PB R (MONO)/L ANT IN Y INPUT 1 TO CONVERTER AUDIO ANT B INPUT 2 PR PB R (MONO)/L R (MONO)/L VIDEO S-VIDEO R (MONO)/L VIDEO S-VIDEO Y/VIDEO AUDIO INPUT 3 AUDIO TO HI-FI CENTER IN INPUT 4 L R OUTPUT L R VIDEO
TIPS ON REAR PANEL CONNECTIONS S-VIDEO and DVI-HDTV connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections in place of the standard video connection if your device has this feature. • If your device has only one audio output (mono sound), connect it to the left audio jack on the television. • Refer to the operating guide of your other electronic equipment for additional information on connecting your hook-up cables.
CONNECTING EXTERNAL AUDIO DEVICES To control the audio level of an external audio amplifier with the TV remote control, connect the system as shown below.
CONNECTING EXTERNAL VIDEO DEVICES The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set Top Box to your TV set is dependent on the model and features of each component. Check the owner’s manual of each component for the location of video and audio inputs and outputs. Before Operating External Video Source The input mode is changed every time the VID1~VID5 button is pressed as shown below.
CONNECTING EXTERNAL VIDEO DEVICES FIRST TIME USE CONNECTING A STEREO SOURCE TO INPUT2~INPUT5 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set below. 2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack. 3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack. 4.
CONNECTING EXTERNAL VIDEO DEVICES CONNECTING AN S-VIDEO SOURCE TO INPUT 3, 4 AND 5 1. Connect the cable from the S-VIDEO OUT of the VCR or the laserdisc player to the INPUT (S-VIDEO) jack, as shown on the TV set below. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack. 3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack. 4.
CONNECTING EXTERNAL VIDEO DEVICES FIRST TIME USE CONNECTING A COMPONENT SOURCE WITH DVI-HDTV CAPABILITY TO INPUT 1 1. Connect the DVI connection cable from the output of the HDTV set top box or DVD player to the DVI-HDTV input as shown on the TV set below. 2. Connect the cable from the AUDIO OUT R of the HDTV set top box or DVD player to the INPUT (AUDIO/R) jack. 3. Connect the cable from the AUDIO OUT L of the HDTV set top box or DVD player to the INPUT (AUDIO/L) jack. 4.
CONNECTING EXTERNAL VIDEO DEVICES CONNECTING A COMPONENT SOURCE TO INPUT 1 OR 2: Y-PBPR. 1. Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the TV set below. Connect the cable from the CB/PB OUT or B-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PB) jack. 3. Connect the cable from the CR/PR OUT or R-Y OUT of the laserdisc/DVD player or HDTV set top box to the INPUT (PR) jack. 4.
THE REMOTE CONTROL In addition to controlling all the functions on your HITACHI LCD Rear PTV, the new remote control is designed to operate different types of VCRs, CBL (Cable TV) converters, satellite receiver, DVD players, and other audio/video equipment with one touch. Basic operation keys are grouped together in one area. To operate your TV, point the remote control at the screen of the TV and press the TV button. The remote will now control your television.
HOW TO USE THE REMOTE TO CONTROL YOUR LCD REAR PTV TV POWER button POWER TV PICTURE-IN-PICTURE CBL/SAT DVD/VCR SWAP PIP MODE PIP SURF DAY/NIGHT FREEZE MENU 햴 DAY/NIGHT button MENU button SURF button SELECT SELECT, MENU, CURSOR buttons MUTE LAST CHANNEL (LAST CH) button LAST CH EXIT EXIT button VOLUME, MUTE buttons VOL CHANNEL SELECTOR buttons ANT button 1 2 3 4 5 6 7 8 9 ANT 0 INFO VID1 VID3 VID4 ASPECT SLEEP VID2 REC THE REMOTE CONTROL CH INFO b
HOW TO USE THE REMOTE TO CONTROL YOUR LCD REAR PTV VOLUME, MUTE button Press the VOLUME up ( ) or down ( ) button until you obtain the desired sound level. To reduce the sound to one half of normal volume (SOFT MUTE) to answer the telephone, etc., press the MUTE button. Press the MUTE button again to turn the sound off completely (MUTE). To restore the sound, press the MUTE button one more time, or press the VOLUME Up ( ) button.
HOW TO USE THE REMOTE TO CONTROL YOUR LCD REAR PTV ASPECT button Press this button to quickly change the picture format ASPECT ratio. Depending on the input signal, the picture format ratio allows you to adjust the images through the following options. 4:3 Standard Use this aspect mode to display conventional (4:3) images. Side panels (gray areas) are placed to the left and right of the image to preserve the original aspect ratio of the source.
HOW TO USE THE REMOTE TO CONTROL YOUR LCD REAR PTV SLEEP button Press this button to display the sleep timer in the lower center of the screen. Every subsequent press of this button will add 15 minutes to this timer up to a maximum of three hours. Once set, use the INFO button to view time remaining. INFO button Press this button when you want to check the channel being received, the picture source, if the channel has stereo (ST) or second audio program (SAP), the time and CHANNEL ID.
PICTURE-IN-PICTURE (PIP) Your HITACHI LCD Rear PTV incorporates dual tuner technology designed for improved viewing enjoyment. This dual tuner feature allows you to view antenna inputs on both the main picture and sub-picture simultaneously, with separate tuning control for each. ANT A input can be viewed as both the main picture and the sub-picture simultaneously. Ant B can only be viewed as a main picture. To select between main picture and PIP sub-picture tuning, press the SWAP button on the remote.
PICTURE-IN-PICTURE (PIP) SPLIT MODE PICTURE-IN-PICTURE Split Mode PIP displays the main picture and sub-picture evenly on the screen. Ant A 10 Ant A 12 Sub Picture Main Picture SURF button PICTURE-IN-PICTURE This feature will automatically scan all active channel numbers (those set in memory) and display them as PIP sub-pictures, Press the SURF button a second time or EXIT button to remove the sub-pictures from the screen.
PICTURE-IN-PICTURE (PIP) FREEZE button (With PIP ON) If you wish to freeze the sub-picture, press the FREEZE button. This is convenient when trying to write down the address for a mail order company, recording statistics for a sporting event, etc. To return the picture to motion, press the FREEZE button again. NOTE: When PIP is on, the FREEZE function will only operate when POP/PIP/SPLIT mode is chosen. FREEZE button (with PIP OFF) Press the FREEZE button to freeze the picture.
USING THE REMOTE TO CONTROL VCR FUNCTIONS Operating the precoded function for your VCR. THE REMOTE CONTROL This remote is designed to operate different types of VCRs. You must first program the remote to match the remote system of your VCR (refer to page 31 for pre-codes). 1. Turn ON your VCR. 2. Aim the remote control at the front of your VCR. 3. Press and release the DVD/VCR button to switch to VCR pre-coded mode. 4.
USING THE REMOTE TO CONTROL CABLE/SATELLITE BOX FUNCTIONS Operating the precoded function for your cable/satellite box. This remote is designed to operate different types of cable/satellite boxes. You must first program the remote to match the remote system of your cable/satellite box (refer to page 31). 1. Turn ON your cable/satellite box. 2. Aim the remote control at the front of your cable/satellite box. 3.
USING THE REMOTE TO CONTROL DVD FUNCTIONS Operating the precoded function for your DVD player. THE REMOTE CONTROL This remote is designed to operate different types of DVD players. You must first program the remote to match the remote system of your DVD player (refer to page 31 for pre-codes). 1. Turn ON your DVD player. 2. Aim the remote control at the front of your DVD player. 3. Press and release the DVD/VCR button to switch to DVD pre-coded mode. 4.
VCR, CABLE, SATELLITE, DVD and AUDIO CODES FOR REMOTE CONTROL CABLE BRAND CODE SATELLITE BRAND CODE VCR BRAND CODE DVD BRAND CODE General Instrument . . . . . . . . . . . . . . . . . . . . . . . . . .17 Hamlin . . . . . . . . . . . . . . . . . . . . . . . . . . . .22,23,24,25 Jerrold . . . . . . . . . . . . . . . .00,01,02,03,04,05,06,07,21 Oak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26,27,28 Panasonic . . . . . . . . . . . . . . . . . . . . . . . . . . . .18,19,20 Pioneer .
ON-SCREEN DISPLAY (OSD) 1. Press MENU on the remote control to display the different features on your HITACHI LCD Rear PTV. 2. Press the CURSOR , , and to highlight a different feature, then press SELECT to choose. 3. Press EXIT on the remote control to quickly exit from a menu. MENU 4. Press CURSOR or to access Favorite Channels menu. SELECT EXIT This part of the screen shows which selections are available. Video Audio Aspect Chan.
ON-SCREEN DISPLAY (OSD) Picture Mode Video Contrast Brightness Color Tint Sharpness Color Temperature Black Enhancement Contrast Mode Reset Video Settings Color Management Color Decoding Auto Color Select between the two picture modes; Day and Night. Adjust contrast. Adjust brightness. Adjust color. Adjust tint. Adjust sharpness. Set this to High for less intense color with more blue, set to Medium for natural color, set to Standard for standard colors or Black/White for more reddish color.
VIDEO Select VIDEO to adjust picture settings and improve picture quality. You can customize each of the Video Inputs to your preference to increase viewing performance and pleasure depending upon the video program being viewed. If RESET is selected, only the selected mode will reset to initial conditions. Video Picture Mode Use this function to choose from automatic picture settings to optimize your TV’s performance. Video Audio Aspect Chan.
VIDEO Video Video Chan. Manager SELECT Locks Day Night 100% Contrast Aspect Brightness 50% Color 50% Tint MENU OR Setup Move ANT A/B Picture Mode Audio SEL Sel Sharpness 50% Color Temperature High Black Enhancement High Contrast Mode Dynamic Reset Video Settings Move SEL Select Use the CURSOR button or to highlight the function to be adjusted. Press the SELECT button or CURSOR button to select the function settings.
VIDEO This function allows you to Reset the Video Menu Settings of the present input and return it to the Day Mode condition depending on the selected Video mode. Reset Video Settings Video Video ANT A/B Picture Mode Day Night Picture Mode 100% Contrast Brightness 50% Color 50% Select menu SELECT “Reset” Settings original factory Tint Sharpness 50% Color Temperature High Black Enhancement High Contrast Mode Dynamic to on Return this the input Video to the settings.
VIDEO Use this function to adjust the percentage of Red, Green and Color according to the user’s preference. Use Tint to adjust flesh tones so they appear natural. Color Decoding Video Video ANT A/B Color Decoding Color Management Color Decoding RGB Auto Color Off Noise Reduction Low SELECT Auto Movie Mode Off or Move SEL Select R G Red 50% Green 50% Color 50% B Tint Reset Move SEL Return Use CURSOR button or to highlight function.
AUDIO Select AUDIO to adjust the TV to your preference and to improve the sound quality. Audio Audio Video Audio Aspect SELECT Locks or Setup Move SEL 45% Bass 50% Balance Chan. Manager MENU Treble Sel L Sound Enhancement Off Audio Source Stereo Internal Speakers On Auto Noise Cancel On Perfect Volume On Loudness On Move Change Value SEL R Return Press CURSOR buttons or to select menu item. Press CURSOR buttons or to adjust the function.
AUDIO Sound Enhancement The following surround settings will reproduce the “live” sound you would hear in concert halls, sports stadiums, movie theaters, etc. with only two channels. Audio Video Audio Aspect SELECT Locks or Setup Move SEL 45% Bass 50% Balance Chan.
ASPECT MODE Aspect Mode Use this function to select the Picture Format Aspect Ratio. Auto Aspect Automatically adjust the Aspect Ratio depending on the input signal to fill the screen. Press CURSOR buttons or to select menu item. Press the SELECT button to select. A “✓” in the box indicates that the feature is ON. NOTES: 1. The Auto Aspect function is recommended on an input signal with VIDEO ID. 2. The Auto Aspect function is best used on component video, S-Video, and 480i composite signals. 3.
CHANNEL MANAGER Chan. Manager Select Antenna if you are using an indoor or outdoor antenna. Select Cable if you have cable TV. Chan. Manager Chan. Manager Ant. A Ant. A Ant. B Move SEL Select SELECT Channel Source Antenna or Auto Channel Scan Cable(1) Cable(2) Start Channel List Move SEL Return Chan. Manager Ant.
CHANNEL MANAGER This feature will automatically store active TV channels in AUTO CHANNEL SCAN. This will allow you to skip unused channels when using CHANNEL UP ( ) or DOWN ( ). Auto Channel Scan Chan. Manager Chan. Manager Ant. A Ant. A Channel Source Antenna Auto Channel Scan Channel Source Antenna Cable(2) Cable(1) Channel List Move SEL Cable(1) Auto Channel Scan Start Cable(2) Start Channel List Select Move SEL Select SELECT Chan. Manager Ant.
CHANNEL MANAGER This function allows you to review which channels are labeled (Ch ID), which have been added to Channel Memory (Scan), and which are protected by Lock. Channel List Chan. Manager Chan. Manager Channel List Ant.
CHANNEL MANAGER Channel ID This section contains advanced features which will make TV viewing easier and more enjoyable. Use this feature to give up to 20 channels a name when Antenna signal source is selected and up to 60 channels a name when Cable TV signal source is selected. Chan. Manager Chan. Manager Ant. A Ant.
LOCKS This function will block out the picture and sound of the selected channel or video input. It can also be used to keep the TV from being viewed for a scheduled time period that you set. Locks The code to enter the Locks feature is a four digit secret code number. The factory preset code is 0000. Use the number buttons to select access code. Video Audio Aspect Please Enter Access Code Chan.
LOCKS Use MOVIE RATINGS to block from showing any movie you feel might have inappropriate content. Movie Ratings Locks Locks Movie Ratings Change Access Code Engage Lock Status Not Rated: TV Time Lock SELECT Movie Ratings TV Ratings G: PG: or PG-13: Canadian Ratings (Eng) Canadian Ratings (Frn) Move SEL R: Select NC-17: X: Move SEL Return Use CURSOR or to select the MOVIE RATING category that you want to block. Press SELECT to block the MOVIE RATING that you have selected.
LOCKS Use TV RATINGS to block from showing any programs or movies you feel might have inappropriate content. TV Ratings Locks Locks TV Ratings Change Access Code Sub Category Engage Lock Status TV Time Lock Movie Ratings TV Ratings SELECT or D TV-G: TV-PG: Select V FV TV-Y7: Canadian Ratings (Frn) SEL S TV-Y: Canadian Ratings (Eng) Move L TV-14: TV-MA: Move SEL Return Use CURSOR or to highlight the category that you want to block.
LOCKS Use CANADIAN RATINGS (ENG) to block any type of movie and television program in Canada that you feel might be inappropriate in its content. Canadian Ratings (Eng) Locks Locks Canadian Ratings (Eng) Change Access Code Status Engage Lock TV Time Lock C: SELECT C8+: Movie Ratings G: or TV Ratings PG: Canadian Ratings (Eng) 14+: Canadian Ratings (Frn) Move SEL 18+: Select Move SEL Return Use CURSOR or to select the CANADIAN RATINGS (ENG) category that you want to block.
LOCKS Use CANADIAN RATINGS (Frn) to block Canadian French programs according to various program ratings that you feel might be inappropriate in its content. Canadian Ratings (Frn) Locks Locks Canadian Ratings (Frn) Change Access Code Status Engage Lock G: TV Time Lock Movie Ratings TV Ratings SELECT or 18 ans+: Canadian Ratings (Frn) SEL 13 ans+: 16 ans+: Canadian Ratings (Eng) Move 8 ans+: Select Move SEL Return Use CURSOR or to highlight the category that you want to block.
SETUP Setup Select SETUP when setting your TV up for the first time. Use the CURSOR or on the remote to highlight the function desired. Video Setup Menu Preference Audio Screen Saver Aspect Set The Clock Chan. Manager SELECT Locks or Setup Move Set The Inputs Set The Color System Set Black Side Panel SEL Sel Set Event Timer Set Closed Captions Move SEL Select Use CURSOR or to select the sub-menu of your choice.
SETUP Set The Menu Background This function allows you to choose from two menu backgrounds. Setup Menu Preference Set The Language English French Spanish Set The Menu Background Shaded Solid Move SEL Select Use CURSOR or to highlight Set The Menu Background (shaded or solid), and press the SELECT button to select setting. Press EXIT to quit menu or select MENU PREFERENCE to return to previous menu.
SETUP The time must be adjusted before you can use the “Set Event Timer” or “TV Time Out” features.
SETUP Use this feature to give a name to any of the five video inputs. Set The Inputs Setup Setup Set The Inputs Menu Preference Video1 Rename List Screen Saver Video2 AVR DVD PVR2 VCR SELECT Video3 CAM DVD2 SAT VCR2 or Video4 CBL LD STB Video5 CBL2 PVR STB2 Set The Clock Set The Inputs Set The Color System Set Black Side Panel Reset Set Event Timer Set Closed Captions Move SEL Select Move Return SEL Press CURSOR , , and to highlight the name of the video inputs.
SETUP Set The Color System This function allows you to automatically change tint and color coordinates for DTV programs. HDTV - High Definition Television - Use for High Vision Signal Y-PBPR from HDTV Set-Top Box. SDTV/DVD - Standard Definition Television or DVD (Digital Versatile Disc Player) Y-CBCR. NOTES: 1. If Color System is set improperly (does not match actual input signal), the color and tint of the main picture will be abnormal. 2.
SETUP This function will automatically turn the LCD Rear Projection TV on and off, one time only, every day, or once a week. This Event Timer is only for Ant A/Ant B. Set Event Timer If the clock is not set, you can not use this function and the screen below will appear in Ant A and Ant B. The message on the screen will disappear after 3 seconds, then the screen automatically goes to the clock setup mode (see page 52). Please Set Clock First.
SETUP CLOSED CAPTIONS are the dialogue, narration, and/or sound effects of a television program or home video which are displayed on the TV screen. Your local TV program guide denotes these programs as or .
LAMP REPLACEMENT Lamp Replacement After extended use, if the TV picture turns dark, the color looks unusual or LAMP INDICATOR light turns on, then it is time to replace the lamp with a new lamp. WARNING: The lamp gets very hot! The lamp may explode if improperly handled. To avoid injury, please observe the following precautions. • Do not open lamp compartment or attempt to remove lamp assembly unless the lamp assembly is being replaced.
LAMP REPLACEMENT LAMP REPLACEMENT 1. Turn off the main power switch and unplug the power cord. Wait at least 30 minutes to allow the lamp to cool down before replacing it. 120V FRONT COVER PUSH POWER NOTE: 2. THE LAMP IS VERY HOT AND MAY CAUSE FIRE OR SEVERE BURNS. WAIT AT LEAST 30~45 MINUTES TO ALLOW THE LAMP TO COOL BEFORE PROCEEDING WITH LAMP REMOVAL. Remove the front cover from the TV set. This is held by a snap on. Pull the front cover outwards until the quick snap on disengages.
LAMP REPLACEMENT 3. Remove the screw securing the lamp cover with a Phillips head screw driver as shown. Remove the lamp cover. LAMP REPLACEMENT SCREW LAMP COVER INPUT 5 S-VIDEO VIDEO L/MONO R AUDIO VOL- VOL+ CH- CH+ INPUT MENU EXIT SELECT PHILLIP HEAD SCREW DRIVER NOTE: 4. THE LAMP IS VERY HOT AND MAY CAUSE FIRE OR SEVERE BURNS. WAIT AT LEAST 30~45 MINUTES TO ALLOW THE LAMP TO COOL BEFORE PROCEEDING WITH LAMP REMOVAL. Remove the two screws that hold the lamp in place.
LAMP REPLACEMENT LAMP REPLACEMENT 6. Without installing the lamp cover, the power will be off and the Lamp Indicator will flash (see page 8). Be sure to install the lamp cover by re-engaging the two clips and tighten the screws before turning the power on, otherwise it may cause unusual colors. SCREW LAMP COVER INPUT 5 S-VIDEO VIDEO L/MONO R AUDIO VOL- VOL+ CH- CH+ INPUT MENU EXIT SELECT PHILLIP HEAD SCREW DRIVER NOTE: 7.
CARE OF YOUR HITACHI TELEVISION AND YOUR REMOTE CONTROL DO Dust the screen and cabinet with a soft cloth. Clean the screen with a soft cloth moistened in warm water and dry with a soft cloth. A mild soap may be used if the screen is extremely dirty. Place your Television away from extreme heat, humidity, and extremely dusty places. Remove the plug from the wall outlet if your Television will not be used for a long period of time, for instances, when you go on vacation.
RECEPTION PROBLEMS • IGNITION NOISE: Black spots or horizontal streaks may appear, picture may flutter or drift. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances. • GHOSTS: Ghosts are caused by the television signal following two paths. One is the direct path and the other is reflected from tall buildings, hills or some other objects. Changing the direction or position of the antenna may improve reception.
USEFUL INFO HITACHI Liquid Crystal Display incorporates advanced power surge protection technology designed to protect against component or circuit damage due to external or internal voltage power surges. IF YOUR TELEVISION SHOULD APPEAR TO HAVE A LOSS OF POWER, PLEASE FOLLOW THIS PROCEDURE: 1. Press the power switch (ON/OFF switch) once. 2. If there is still no power, wait 30 seconds and press the power switch again. 3. If there is still no power, unplug the power cord from the wall.
USEFUL INFO Features: • • • • • • • • • • • • • • Superfine Picture Quality 1280 Line Horizontal Resolution Remote (Controls many VCR brands, cable boxes, satellite boxes, and other audio equipment). New Easy-to-Use (3-Language) On-Screen Menu Full Set of Input Jacks, including S-VIDEO COMPONENT VIDEO: Y-PB/PR Six Aspect Modes Closed Caption Decoder 2-Tuner Picture in Picture Dual Antenna Inputs Video Input Sensor 3 Dimensional Y/C Comb Filter Compatible with 1080i, 720p, 480p and 480i input signals.
USEFUL INFO e c i v r e s To locate an authorized HITACHI service facility in the continental U.S.A. and Canada, DIAL TOLL FREE 7 days a week, 24 hours a day (1-800-448-2244) Hitachi America, LTD. Home Electronics Division Hitachi has made every effort to assure you hours of trouble free operation from your unit. However, should you require service, a network of Hitachi Authorized Service Facilities has been established in all 50 states and Puerto Rico.
USEFUL INFO Hitachi Canada, LTD. Digital Media Division Should you have any questions regarding warranty, service, operation, or technical assistance, please contact: In Canada: 1-800-HITACHI (1-800-448-2244) Monday - Friday EST 9:00am - 7:00pm Saturday EST 9:00am - 5:00pm Look for your French Manual on the outside of the box. If the manual is missing, call 1-800-HITACHI (1-800-448-2244) for a copy.
INDEX INDEX Clock Time, 52 A Date, 52 Closed Captions Analog Captions, 56 Color System, 54 Color Temperature, 35 Color, 35 Contrast, 35 Accessories, 4 Antennas (Connecting), 5, 6 Aspect Ratio, 23 Audio (Sound Enhancement) SRS, 39 BBE, 39 Audio Settings, 38 - 39 D Audio Source, 38 DVI-HDTV, 11, 12, 18 Auto Color, 37 E Auto Noise Cancel, 38 Event Timer ANT A/B, 55 B Balance, 38 Bass, 38 I Black Enhancement, 35 Black Side Panel, 54 Brightness, 35 Input Setup, 53 C Channel Manager, 41 - 42 Chan
INDEX L Picture-in-Picture (PIP), 25 - 27 Lamp Picture-outside-Picture (POP), 25 Lamp Indicator, 8 Lamp Replacement, 57-60 Language R Menu Language, 50 Locks Remote Control Functions, 20 - 30 Programming Codes, 28 - 31 Installing Batteries, 4 Change Access Code, 45 Channel Lock, 45 Input Lock, 45 Front Panel Lock, 45 TV Time Lock, 45 Movie Ratings, 46 S TV Ratings, 47 TV Ratings (Canadian - English), 48 TV Ratings (Canadian - French), 49 Loudness, 38 Sharpness, 35 Sound Enhancement, 39 Speakers,
NOTES 69
NOTES 70
NOTES 71
QR63612