PROJECTION COLOR TV Operating Guide for 51F710, 57F710, 65F710, 51F710S, 57F710S, 65F710S IMPORTANT SAFETY INSTRUCTIONS ................................................................................ 2-3 FIRST TIME USE .................................................................................................................. 4-19 THE REMOTE CONTROL .................................................................................................. 20-32 ON-SCREEN DISPLAY..............................
IMPORTANT SAFETY INSTRUCTIONS SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI TELEVISION Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions. Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your HITACHI television.
IMPORTANT SAFETY INSTRUCTIONS Read before operating equipment Follow all warnings and instructions marked on this television. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8.
ACCESSORIES Check to make sure you have the following accessories before disposing of the packing material. FIRST TIME USE REMOTE CONTROL “Z” ALLEN KEY BATTERIES (“AA”) 2. For 57” and 65” Models Only 3. OPTIONAL TV TOP SHELF (NOT INCLUDED, ORDER SEPARATELY) Model No. Part No. 1. SLF10 QJ01611 CAUTION: This SLF10 TV Top Shelf for use only with Hitachi 51F710, 51F710S and 57F710, 57F710S. Use with other apparatus is capable of resulting in instability causing possible injury. 1.
HOW TO SET UP YOUR NEW HITACHI PROJECTION TV ANTENNA LOCATION Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure that the location selected allows a free flow of air to and from the perforated back cover of the set. To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can become excessively hot, for example, in direct sunlight or near a heating appliance, etc.
HOOK-UP CABLES AND CONNECTORS FIRST TIME USE Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell audio/video products. Below are illustrations and names of common connectors.
FRONT PANEL CONTROLS FIRST TIME USE h i e INPUT 5 AUDIO S-VIDEO VIDEO L/MONO R VOL- VOL+ CH- CH+ INPUT MENU F E H G EXIT SELECT b a MAGIC FOCUS CURSOR g e d c f a MENU/SELECT button This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote. This button also serves as the SELECT button when in MENU mode. b INPUT/EXIT button Press this button to display the input menu, Ant A/B, INPUT:1,2,3,4 and 5.
FRONT PANEL JACKS AND CONNECTORS FIRST TIME USE The front panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following examples: INPUT 5 INPUT 5 AUDIO S-VIDEO VIDEO L/MONO NOTE: AUDIO R S-VIDEO VIDEO L/MONO R 1. Completely insert connection cord plugs when connecting to front panel jacks. If you do not, the played back picture may be abnormal. 2. If you have a S-VHS VCR, use the S-INPUT cable in place of the standard video cable. 3.
REAR PANEL JACKS a e k HDMI 1 ANT B c MONITOR OUT S-VIDEO INPUT 4 INPUT 3 INPUT 2 Y/ VIDEO INPUT 1 Y/ VIDEO PB PB PR PR (MONO) (MONO) g h OPTICAL OUT Digital Audio d Upgrade Card Apparatus Claims of U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098; 4,907,093; and 6,381,747 licensed for limited viewing uses only. VIDEO (MONO) (MONO) L RS232C TV AS CENTER AUDIO 1 2 6 R 3 7 4 8 5 9 AUDIO TO HI-FI jf b i a Antenna Input ANT A- A 75-Ohm RF antenna or CATV (Cable TV) input.
REAR PANEL JACKS FIRST TIME USE f HDMI1 (High Definition Multimedia Interface) (INPUT 1) About HDMI HDMI is the next-generation all digital interface for consumer electronics. HDMI enables the secure distribution of uncompressed high-definition video and multi-channel audio in a single cable. Because digital television (DTV) signals remain in digital format, HDMI assures that pristine high-definition images retain the highest video quality from the source all the way to your television screen.
REAR PANEL JACKS k CableCARD Slot Connect a coaxial cable to ANT A terminal of the Rear Panel Jacks. Insert the CableCARD into the slot (Top of card should be facing right as shown). Digital Cable CableCARD (Top of card faces right) ANT A D IS TH HDMI 1 RT E INS ANT B MONITOR OUT S-VIDEO INPUT 4 INPUT 3 INPUT 2 Y/ VIDEO INPUT 1 Y/ VIDEO PB PB PR PR EN RD A leC b Ca OPTICAL OUT Digital Audio Upgrade Card Apparatus Claims of U.S. Patent Nos.
REAR PANEL CONNECTIONS FIRST TIME USE TYPICAL FULL-FEATURE SETUP DVD Player Y OUTPUT PB/CB PR/CR L R Outside antenna or digital cable CableCARD (Top of card faces right) ANT A External Digital Component with HDMI output capability HDMI OUT HDMI 1 ANT B MONITOR OUT S-VIDEO INPUT 4 INPUT 3 INPUT 2 Y/ VIDEO INPUT 1 Y/ VIDEO PB PB PR PR To an amplifier/receiver with optical input capability. OPTICAL OUT Digital Audio Upgrade Card Apparatus Claims of U.S. Patent Nos.
TIPS ON REAR PANEL CONNECTIONS S-VIDEO, Y-PbPr and HDMI connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections in place of the standard video connection if your device has this feature. • If your device has only one audio output (mono sound), connect it to the left audio jack on the television. • Refer to the operating guide of your other electronic equipment for additional information on connecting your hook-up cables.
CONNECTING EXTERNAL AUDIO SOURCES FIRST TIME USE Match the numbers below to the diagram for speaker placement. 1 The television’s internal speakers will act as center speaker (select Audio-Internal Speakers-TV as Center). 2 These FRONT left and right speakers are connected to the FRONT output of a separate audio amplifier. 3 These REAR left and right speakers are connected to the REAR output of a separate audio amplifier.
CONNECTING EXTERNAL VIDEO SOURCES The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set Top Box to your TV set is dependent on the model and features of each component. Check the owner’s manual of each component for the location of video and audio inputs and outputs. Before Operating External Video Source Connect an external source to the INPUT terminal, then press the INPUTS button to show the INPUTS menu.
CONNECTING EXTERNAL VIDEO SOURCES FIRST TIME USE CONNECTING A STEREO SOURCE TO INPUT1~INPUT5 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set below. 2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack. 3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack. 4.
CONNECTING EXTERNAL VIDEO SOURCES CONNECTING AN S-VIDEO SOURCE TO INPUT 3, 4 AND 5 1. Connect the cable from the S-VIDEO OUT of the VCR or the laserdisc player to the INPUT (S-VIDEO) jack, as shown on the TV set below. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack. 3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack. 4.
CONNECTING EXTERNAL VIDEO SOURCES FIRST TIME USE CONNECTING A COMPONENT SOURCE WITH HDMI or DVI CAPABILITY TO INPUT 1 1. Connect the HDMI or DVI to HDMI connection cable from the output of the HDTV set top box or DVD player to the HDMI input as shown on the TV set below. When using a component with DVI output, you also have to connect the AUDIO OUT (R/L) of the component to the AUDIO IN (R/L) of INPUT 1. 2.
CONNECTING EXTERNAL VIDEO SOURCES CONNECTING A COMPONENT SOURCE TO INPUT 1 OR 2: Y-PBPR. 1. Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the TV set below. Connect the cable from the CB/PB OUT or B-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PB) jack. 3. Connect the cable from the CR/PR OUT or R-Y OUT of the laserdisc/DVD player or HDTV set top box to the INPUT (PR) jack. 4.
THE REMOTE CONTROL In addition to controlling all the functions on your HITACHI Projection TV, the new remote control is designed to operate different types of VCRs, CATV (Cable TV) converters, set-top-boxes, satellite receivers (SAT) and DVD players with one touch. Basic operation keys are grouped together in one area. To operate your TV, point the remote control at the screen of the TV and press the TV button. The remote will now control your television.
HOW TO USE THE REMOTE TO CONTROL YOUR TV a b d g j f e h k n i m l THE REMOTE CONTROL n o p q c a POWER button Press this button to turn the TV set on or off when the remote is in TV mode. (See page 20 for instructions on how to set the remote control to TV mode.) b MODE buttons These buttons allow the remote to control your TV, VCR, DVD, Cable box/Satellite box depending on which button is pressed. c PAUSE button Press the PAUSE button to freeze the picture.
HOW TO USE THE REMOTE TO CONTROL YOUR TV e ASPECT button Press this button to quickly change the picture format ASPECT ratio. Depending on the input signal format received, the picture format ratio allows you to adjust the images through the following options. 4:3 STANDARD Use this aspect mode to display conventional (4:3) images. Side panels (gray areas) are placed to the left and right of the image to preserve the original aspect ratio of the source.
HOW TO USE THE REMOTE TO CONTROL YOUR TV f INPUTS button When the remote control is in TV mode, press this button to access the INPUTS menu. Use the CURSOR and SELECT buttons to select the inputs that are being used. Pressing the INPUTS button repeatedly will also cycle through the Inputs menu items. Then press the SELECT button to select. Input 5 Ant B Ant A Input 1 Input 2 Move SEL Select Select to choose Antenna B. Ant A Select to choose Antenna A. Input 1 Select to choose Input 1 for Video 1.
HOW TO USE THE REMOTE TO CONTROL YOUR TV g PICTURE-IN-PICTURE button See separate section on pages 26-28 for a description. h MENU button The MENU button will start the On-Screen Display. i GUIDE button [Cable Box (CBL), Satellite Receiver (SAT)/Set-Top-Box (STB) mode only] The use of this button is only applicable when the remote control is in (CBL) and (SAT/STB) mode. Press this button to access the Channel Guide of the (CBL), and (SAT/STB). j EXIT button This button will exit all On-Screen Displays.
HOW TO USE THE REMOTE TO CONTROL YOUR TV m VOLUME (VOL), MUTE button Press the VOLUME button (G or H) until you obtain the desired sound level. To reduce the sound to one half of normal volume (SOFT MUTE) to answer the telephone, etc., press the MUTE button. Press the MUTE button again to turn the sound off completely (MUTE). To restore the sound, press the MUTE button one more time, or VOL Up (G).
PICTURE-IN-PICTURE (PIP) Your HITACHI Projection TV incorporates Two Tuner technology designed for improved viewing enjoyment. This Two Tuner feature allows you to view antenna inputs on both the main picture and sub-picture simultaneously, with separate tuning control for each. ANT A input can be viewed as both the main picture and the sub-picture simultaneously. ANT B can only be viewed as a main picture. To select between main picture and PIP sub-picture tuning, use the CURSOR buttons on the remote.
PICTURE-IN-PICTURE (PIP) PIP MODE PICTURE-IN-PICTURE This feature is only available with a 1080i signal. To prevent a pattern burn, occasionally move the sub-picture using the CURSOR buttons. Main Picture Sub Picture SPLIT MODE PICTURE-IN-PICTURE Split Mode PIP displays the main picture and sub-picture evenly on the screen. Sub Picture Main Picture NOTE: 1 2 3 4 5 6 7 8 9 10 11 12 Press the SELECT button to stop the Surf mode or channel scan.
PICTURE-IN-PICTURE (PIP) b PAUSE button If you wish to freeze the sub-picture, press the PAUSE button. This is convenient when trying to write down the address for a mail order company, recording statistics for a sporting event, etc. To return the picture to motion, press the EXIT button. Press the PAUSE button repeatedly to toggle between FREEZE modes (Main Freeze, SPLIT and STROBE).
USING THE REMOTE TO CONTROL CABLE BOX FUNCTIONS Operating the precoded function for your cable box. This remote is designed to operate different types of cable boxes. You must first program the remote to match the remote system of your cable box (refer below for pre-codes). 1. Turn ON your cable box. 2. Aim the remote control at the front of your cable box. 3. To switch to Cable (CBL) pre-coded mode, press and release the CABLE (CBL) button. 4.
USING THE REMOTE TO CONTROL SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS Operating the precoded function for your set-top-box/satellite receiver. THE REMOTE CONTROL This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the remote system of your set-top-box/satellite systems (refer below for pre-codes). 1. Turn ON your set-top-box/satellite systems. 2. Aim the remote control at the front of your set-top-box/satellite systems. 3.
USING THE REMOTE TO CONTROL DVD FUNCTIONS Operating the precoded function for your DVD player. This remote is designed to operate different types of DVD players. You must first program the remote to match the remote system of your DVD player (refer below for pre-codes). 1. Turn ON your DVD player. 2. Aim the remote control at the front of your DVD player. 3. To switch to DVD pre-coded mode, press and release the DVD button. 4.
USING YOUR REMOTE TO CONTROL VCR FUNCTIONS Operating the precoded function for your VCR. THE REMOTE CONTROL This remote is designed to operate different types of VCRs. You must first program the remote to match the remote system of your VCR (refer below for pre-codes). 1. Turn ON your VCR. 2. Aim the remote control at the front of your VCR. 3. To switch to VCR pre-coded mode, press and release the VCR button. 4.
ON-SCREEN DISPLAY (OSD) 1. Press MENU on the remote control to display the different features on your HITACHI Projection TV. 2. Press the CURSOR buttons to navigate and highlight a different feature of the On-Screen Display menu. Press the SELECT button to select. 3. Press EXIT on the remote control to quickly exit from a menu. This part of the screen shows which selections are available. Video Audio Aspect Chan.
ON-SCREEN DISPLAY (OSD) Picture Mode Contrast Brightness Color Tint Sharpness Color Temperature Video Black Enhancement Edge Enhancement Reset Video Settings Color Management Color Decoding Auto Color Audio ON-SCREEN DISPLAY Aspect NOTE: Select between the two picture modes; Day and Night. Adjust contrast. Adjust brightness. Adjust color. Adjust tint. Adjust sharpness.
ON-SCREEN DISPLAY (OSD) Channel Manager Locks Set the Antenna Auto Channel Scan Signal Meter Channel List Set Antenna settings. Set Auto Channel Scan. Access Signal Meter. Set Channel List. Change Access Code Engage Lock TV Time Lock Movie Ratings Change Lock access code. Choose to lock channel, video input, and/or front panel. Set specific time to Lock TV. Block various types of movies and video types based on motion picture ratings.
VIDEO Video Select VIDEO to adjust picture settings and improve picture quality. You can independently customize each of the Video Inputs to your preference to increase viewing performance and pleasure depending upon the video program being viewed. If RESET is selected, only the selected input will reset to initial conditions. Picture Mode Use this function to choose from automatic picture settings to optimize your TV’s performance. Video Audio Aspect Chan.
VIDEO Use the CURSOR buttons G or H to highlight the function to be adjusted. Press the CURSOR buttons F or E to adjust the function. Press the SELECT button to select the function settings. Press MENU to return to main menu or select PICTURE MODE to return to previous menu. Press EXIT to quit menu. Contrast Brightness Use this function to change the contrast between black and white levels in the picture. Use this function to adjust overall picture brightness.
VIDEO Reset Video Settings This function allows you to Reset the Video Menu Settings of the present input and return it to the Day VIDEO mode. Video ANT A/B Picture Mode Day Contrast 100% Brightness Select menu 50% Tint Sharpness “Reset” settings original High Edge Enhancement High Middle Black Enhancement Reset Video Settings to on factory return this the input settings.
VIDEO Color Decoding Use this function to adjust and balance the percentage of Red, Green and Blue according to the user’s preference in each of the four color temperature settings. Use TINT to adjust flesh tones so they appear natural. Video Video Color Decoding Color Management Color Decoding Auto Color Noise Reduction Auto Movie Mode Move SEL Select RGB Off Red Off R Green Off G B 50% Color 50% Tint Move 50% Reset SEL Return Use the CURSOR buttons to highlight function.
Audio AUDIO Select AUDIO to adjust the TV to your preference and to improve the sound quality. Audio Video Treble Audio Aspect 50% SRS Off Balance Chan. Manager Locks Timers SEL Sel L BBE Hard Internal Speakers On Audio Source Setup Move 50% Bass Auto Noise Cancel Perfect Volume Loudness Move Change Value R Stereo Off Off Off SEL Return Press the CURSOR buttons G, H, to select menu item. Press the CURSOR buttons F or E to adjust the function.
AUDIO Audio Source Multi-Channel Television Sound will allow you to select STEREO (a stereo broadcast), MONO (monaural sound) used when receiving a weak stereo broadcast or 2nd Audio Prog (SAP) which may be a secondary language, weather report, etc. The sources received will be displayed at the top right edge of the TV. The source you select will be displayed above the sources received. See example below for each selection when both stereo and second audio are received (monaural is always received).
AUDIO Use the functions below if your TV is connected to an amplifier/receiver with optical digital input with Dolby Digital or PCM decoder capabilities.
ASPECT Aspect Use this function to select the Picture Format Aspect Ratio. Aspect Video Mode 16:9 Standard 4:3 Standard 4:3 Zoom1 Audio Aspect Chan. Manager Auto Aspect Locks Vertical Position Timers Setup Move SEL 16:9 Zoom 4:3 Expanded 4:3 Zoom2 0 Sel Move SEL Return Auto Aspect Automatically adjust the Aspect Ratio depending on the input signal to fill the screen. Press THE CURSOR buttons G, H, F, E to select menu item. Press THE SELECT button to select.
CHANNEL MANAGER Chan. Manager Select Channel Manager to set your Antenna options, run Auto Channel Scan, Check Signal Meter and Set Channel List. Chan. Manager Video Set The Antenna Audio Auto Channel Scan Aspect Signal Meter Chan. Manager Channel List Locks Move Timers Setup Move SEL SEL Return Sel Press the CURSOR buttons G, H to highlight function, the press the SELECT button to select. Set The Antenna This feature will select Antenna options. Chan. Manager Chan.
CHANNEL MANAGER Signal Meter Select Signal Meter when using an indoor or outdoor antenna. This feature will show the signal strength and peak values of the Antenna signal to help you adjust your antenna to optimize signal reception. Chan. Manager Chan.
LOCKS Locks This function will block out the picture and sound of the selected channel or video input. It can also be used to keep the TV from being viewed for a scheduled time period that you set. The code to enter the Locks feature is a four digit access code number. The factory preset code is 0000. Use the number buttons to enter the access code. Video Audio Aspect Please Enter Access Code Chan.
LOCKS Movie Ratings Use MOVIE RATINGS to prevent viewing of any movie that you feel may be inappropriate due to its content. Locks Locks Movie Ratings Change Access Code Engage Lock Status Not Rated: TV Time Lock G: Movie Ratings PG: TV Ratings PG-13: Canadian Ratings (Eng) R: Canadian Ratings (Frn) Move SEL Select NC-17: X: Move SEL Return Use the CURSOR buttons G or H to select the MOVIE RATING category that you want to block.
LOCKS TV Ratings Use TV RATINGS to prevent the viewing of any TV program that you feel may be inappropriate due to its content. Locks Locks TV Ratings Change Access Code Engage Lock Status TV Time Lock TV-Y: Movie Ratings TV Ratings TV-Y7: Canadian Ratings (Frn) TV-PG: SEL L Sub Category S V FV TV-G: Canadian Ratings (Eng) Move D Select TV-14: TV-MA: Move SEL Return Use the CURSOR buttons G or H to highlight the category that you want to block.
LOCKS Canadian Ratings (Eng) Use Canadian Ratings (Eng) to block any type of movie and television program in Canada that you feel might be inappropriate in its content. Locks Locks Canadian Ratings (Eng) Change Access Code Status Engage Lock TV Time Lock G: TV Ratings PG: Canadian Ratings (Eng) 14+: Canadian Ratings (Frn) Move SEL C: C8+: Movie Ratings 18+: Select Move SEL Return Use the CURSOR buttons G or H to select the CANADIAN RATINGS (Eng) category that you want to block.
LOCKS Canadian Ratings (Frn) Use CANADIAN RATINGS (FRN) to block Canadian French programs according to various program ratings that you feel might be inappropriate in its content. Locks Locks Canadian Ratings (Frn) Change Access Code Status Engage Lock TV Time Lock 13 ans+: TV Ratings 16 ans+: Canadian Ratings (Eng) 18 ans+: Canadian Ratings (Frn) Move SEL G: 8 ans+: Movie Ratings Select Move SEL Return Use the CURSOR buttons G or H to highlight the category that you want to block.
TIMERS Timers Select Timers to set your Clock, Sleep Timer, Event Timer and Day/Night Timer Recordings. Timers Video Set The Clock Audio Set Sleep Timer Aspect Set Day/Night Timer Chan. Manager Set Event Timer Locks Move Timers Setup Move Set The Clock SEL Return SEL Sel The Clock must be adjusted before you can use the “Set Event Timer” or Day/Night Timer” feature.
TIMERS Set Sleep Timer Select this feature to set your Sleep Timer from 30 minutes to 3 hours (30 minute increments). Timers Set The Clock Set Sleep Timer Set Day/Night Timer Timers Set The Clock Set Sleep Timer 0:00 Set Day/Night Timer Set Event Timer Move 0:30 Set Event Timer Set Set Move Press the CURSOR button E repeatedly to set your Timer from 0:00, 0:30, 1:00, 1:30, 2:00, 2:30 and 3:00.
TIMERS Set Event Timer This function will automatically operate the Projection TV viewing reservation of a program. If the clock is not set, you can not use this function and the screen below will appear. The message on the screen will disappear after 3 seconds, then the screen automatically goes to the clock setup mode (see page 51). Please Set Clock First.
SETUP Setup Select SETUP when setting your TV up for the first time. Use the CURSOR buttons G or H on the remote to highlight the function desired. Video Setup Magic Focus Tune Up Audio Menu Preference Aspect Set The Inputs Chan.
SETUP Magic Focus Tune Up Auto Digital Convergence Adjustment Please turn ON your television for at least 20 minutes before using this feature. The Magic Focus button on control panel will not work when adjustment mode is set to Manual (see page 56 or 57). Your HITACHI Projection TV has three color projection tubes: one for red, one for green, one for blue. When mixed together in the proper proportion, the output of these three color tubes can produce any color.
SETUP Manual Convergence Adjustment Mode (9 Point Manual Adjustment) NOTES: 1. 2. 3. Please turn ON your television for at least 20 minutes before using this feature. Auto Adjustment Mode is recommended. If convergence is still not acceptable, use the Manual Adjustment Mode. If Auto Adjust mode is selected or the Magic Focus button is pressed, all manual adjust mode settings will be erased.
SETUP Manual Convergence Adjustment Mode (117 Point Manual Adjustment) NOTES: 1. 2. 3. Please turn ON your television for at least 20 minutes before using this feature. Auto Adjustment Mode is recommended. If convergence is still not acceptable, use the Manual Adjustment Mode. If Auto Adjust mode is selected or the Magic Focus button is pressed, all manual adjust mode settings will be erased.
SETUP Menu Preference This feature will allow you to select any one of three different languages for all on-screen displays.
SETUP Menu Background This function allows you to choose from two menu backgrounds. Setup Menu Preference Set The Language English French Spanish Set The Menu Background Shaded Solid Move SEL Select Use the CURSOR buttoms F , E to highlight SET THE MENU BACKGROUND (shaded or solid), and press the SELECT button to select setting. Press EXIT to quit menu or the CURSOR buttons F to return to previous menu.
SETUP Video 2 Auto Link Use this function to automatically turn the TV on and tune to Video2 when it detects a video signal to input 2.
SETUP Set Virtual HD NOTE: Set Virtual HD is not available (grayed out) in Digital Channels and 1080i input. Set Black Side Panel NOTE: Use this feature to select between 1080i and 540p. The BLACK SIDE PANEL function turns the gray side bars on/off when watching 4:3 signals in Standard mode. The top/bottom gray bar will appear in SPLIT MODE PIP and SPLIT FREEZE. The TV set will always return to “Set Black Side Panel - OFF” setting every time the TV is powered “OFF”.
SETUP Set Closed Caption Closed Captions are the dialogue, narration, and/or sound effects of a television program or home video which are displayed on the TV screen. Your local TV program guide denotes these programs as or .
SETUP Set Monitor Out This feature will select the source of the Monitor Output. Setup Setup Set Monitor Out Magic Focus Tune Up Video Out Monitor Menu Preference Set The Inputs TV Tuner Out Set Virtual HD Set Black Side Panel Audio Out Fixed Set Closed Captions Variable Set Monitor Out About Your TV Move SEL Select Move SEL Return Monitor- Select Monitor to output the audio and video signals of the chosen input source (ANT A, ANT B, VID3-VID5) to a VCR or other A/V device.
SETUP Set AV Control This feature will select the AV Control feature. Set this feature if you want to control some of the TV functions from an external home control system. Setup Setup Set AV Control CableCARD Info Set AV Control If you want to use the AV Control Upgrades function, please set the RS232C. Quick Start Up Move SEL Select Connected RS232C Move SEL Return Use the CURSOR buttons and the SELECT button to check the Connected RS232C box.
CARE OF YOUR HITACHI TELEVISION AND YOUR REMOTE CONTROL DO Dust the screen and cabinet with a soft cloth. Clean the screen with a soft cloth moistened in warm water and dry with a soft cloth. A mild soap may be used if the screen is extremely dirty. Place your Television away from extreme heat, humidity, and extremely dusty places. Remove the plug from the wall outlet if your Television will not be used for a long period of time, for instances, when you go on vacation.
RECEPTION PROBLEMS • IGNITION NOISE: Black spots or horizontal streaks may appear, picture may flutter or drift. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances. • GHOSTS: Ghosts are caused by the television signal following two paths. One is the direct path and the other is reflected from tall buildings, hills or some other objects. Changing the direction or position of the antenna may improve reception.
ure rd cor is p TV rec lug t is s Try ge w d itch an i n oth ed ''O er N" cha Ch nn eck el ( an sta ten tion na Ch tro eck con ub ne an le) ctio ten ns na Ch (ba for eck c b k r ou oke of T tsid n le V) Ch ea ad eck nte -in nn for wir a loc e al i Ad nte jus tC rfe ren on tra ce Ad s t co jus ntr tB ol rig h tne Ad ss jus con tC tro olo l rc Ad o jus ntr tT o l int con Ad tro jus l tV olu me con tro l SYMPTOMS CH TR ECK Y T TH HE ES Be SE E I sur AD TEM ee xte JU Be rna ST S AN sur l co ME D ep nn e ow NT
USEFUL INFO Features: • • • • • • • • • • • • • • • • • • • • • Superfine Picture Quality 1280 Line Horizontal Resolution Remote (Controls many PVR/VCR brands, cable boxes, satellite boxes, and other audio equipment).
USEFUL INFO To locate an authorized HITACHI service facility in the continental U.S.A. and Canada, DIAL TOLL FREE 7 days a week, 24 hours a day (1-800-448-2244) Hitachi America, LTD. Home Electronics Division Hitachi has made every effort to assure you hours of trouble free operation from your unit. However, should you require service, a network of Hitachi Authorized Service Facilities has been established in all 50 states and Puerto Rico.
USEFUL INFO Hitachi Canada, LTD. Digital Media Division Should you have any questions regarding warranty, service, operation, or technical assistance, please contact: In Canada: 1-800-HITACHI (1-800-448-2244) Monday - Friday EST 9:00am - 7:00pm Saturday EST 9:00am - 5:00pm Look for your French Manual on the outside of the box. If the manual is missing, call for a copy.
57” DISASSEMBLY/ASSEMBLY INSTRUCTIONS IMPORTANT POINTS: (a) (b) (c) (d) Do not attempt to perform this work by yourself. Request an installation specialist to install this unit. HITACHI assumes no responsibility or liability for injury/damage as a result of consumer installation and handling. Be advised that improper consumer installation/handling is not covered by manufacturer’s warranty. This Projection Television weighs 205 pounds and has many sensitive components.
57” DISASSEMBLY/ASSEMBLY INSTRUCTIONS 1 - SEPARATION PROCEDURE CONTINUED STEP 4 Cont. (c) (d) STEP 5 Remove the joint connector bolts from each side of the back cover using the allen wrench that is provided inside of the instruction bag, see (a) and (b). (a) (b) STEP 6 Remove from the back side of the TV set only the top 4 screws of the lower rear cover, see (b), as shown by the arrows on the rear cabinet label, see (a). Do not remove the rear cover board.
57” DISASSEMBLY/ASSEMBLY INSTRUCTIONS 2 - RE-ASSEMBLY PROCEDURE STEP 8 To re-assemble the set, lift the top portion and align onto the STEP 9 Re-install the joint connector bolts (4 pcs.) that were removed bottom cabinet. Gently lower the top portion until it sits flush on the bottom. in step 5 of the disassembly. STEP 10 Re-install the top (4) four screws into the lower rear cover, see (a). Re-install the (4) four side screws that hold the back cover to the cabinet, see (b).
65” DISASSEMBLY/ASSEMBLY INSTRUCTIONS IMPORTANT POINTS: (a) (b) (c) (d) Do not attempt to perform this work by yourself. Request an installation specialist to install this unit. HITACHI assumes no responsibility or liability for injury/damage as a result of consumer installation and handling. Be advised that improper consumer installation/handling is not covered by manufacturer’s warranty. This Projection Television weighs 309 pounds and has many sensitive components.
65” DISASSEMBLY/ASSEMBLY INSTRUCTIONS 1 - SEPARATION PROCEDURE CONTINUED STEP 3 Cont. (c) (d) STEP 4 Remove the joint connector bolts from each side of the TV set using the allen wrench that is provided inside of the instruction bag, see (a) and (b). (a) (b) STEP 5 Remove from the back side of the TV set only the top 4 screws of the lower rear cover, see (b), as shown by the arrows on the rear cabinet label, see (a). Do not remove the rear cover board.
65” DISASSEMBLY/ASSEMBLY INSTRUCTIONS 2 - RE-ASSEMBLY PROCEDURE STEP 7 To re-assemble the set, lift the top portion and align onto the STEP 8 Re-install the joint connector bolts (4 pcs.) that were removed bottom cabinet. Gently lower the top portion until it sits flush on the bottom. in step 4 of the disassembly. STEP 9 Re-install the top (4) four screws into the lower rear cover, see (a). (a) STEP 10 Re-connect the sensor connector to the sensor board, see (a). Re-install the sensor box, see (b).
INDEX L A Language Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Locks Change Access Code . . . . . . . . . . . . . . . . . . . . . . .46 Channel Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Input Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Front Panel Lock . . . . . . . . . . . . . . . . . . . . . . . . . . .46 TV Time Lock . . . . . . . . . . . . . . . . . .
END USER LICENSE AGREEMENT FOR HITACHI DTV SOFTWARE IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you and Hitachi America, Ltd., Home Electronics Division ("HAL-HED"). By using this Hitachi digital television (the "DTV") and its software (the "Software"), you agree to be bound by the terms of this License Agreement. IF YOU DO NOT AGREE TO BE BOUND BY THIS LICENSE AGREEMENT, DO NOT USE THIS DTV AND ITS SOFTWARE.
END USER LICENSE AGREEMENT FOR HITACHI DTV SOFTWARE 7. LIMITATION OF LIABILITY.
QR61703