Grass Trimmer/Brush Cutter Rasentrimmer/Motorsense Coupe- Herbes/Débroussailleuse Bordatore/Decespugliatore Motor Zeis/Motor bosmaaier Motoguadañas/Desbrozadoras Foice a motor/Roçadora CG 24EBSP (SL) / CG 24EBSP (S) / CG 24EBS (SL) CG 24EBS (S) / CG 24EBDP (SL) / CG 24EBDP (SLN) CG 24EBD (SL) / CG 24EBD (SLN) / CG 27EBSP (SL) CG 27EBSP (S) / CG 27EBS (SL) / CG 27EBS (S) CG 27EBDP (SL) / CG 27EBDP (SLN) / CG 27EBD (SL) CG 27EBD (SLN) CG24EBSP (SL) Read the manual carefully before operating this machine.
1 2 3 1 5 4 2 3 4 5 7 8 7 6 6 7 8 11 9 12 16 15 10 14 13 9 17 10 11 2 000Book_CG24EBSP(SL)_WE.
12 13 14 18 19 20 17 15 16 18 19 24 23 21 22 20 20 21 22 27 25 B A 3 000Book_CG24EBSP(SL)_WE.
23 24 25 26 27 28 24 T 15 m 29 30 31 28 0.6 mm 32 33 34 10 cm 30 29 4 000Book_CG24EBSP(SL)_WE.
35 36 31 10 cm 37 34 c 10 m 33 31 38 11–14 cm 32 39 11–14 cm 35 5 000Book_CG24EBSP(SL)_WE.
English (Original instructions) MEANINGS OF SYMBOLS NOTE: Some units do not carry them. Symbols WARNING The following show symbols used for the machine. Be sure that you understand their meaning before use. It is important that you read, fully understand and observe the following safety precautions and warnings. Careless or improper use of the unit may cause serious or fatal injury. Ignition stop Read, understand and follow all warnings and instructions in this manual and on the unit.
English WHAT IS WHAT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24.
English WARNINGS AND SAFETY INSTRUCTIONS Operator safety ○ Always wear a safety face shield or goggles. ○ Always wear heavy, long pants and non-slip boots and gloves. Do not wear loose clothing, jewelry, short pants, sandals or go barefoot. Secure hair so it is above shoulder length. ○ Do not operate this tool when you are tired, ill or under the influence of alcohol, drugs or medication. ○ Do not operate the tool at night or under bad weather conditions when visibility is poor.
English NOTE Helpful information for correct function and use. CAUTION Do not disassemble the recoil starter. You may get a possibility of personal injury with recoil spring. SPECIFICATIONS Model Engine Displacement (cm3) Spark plug Idling speed (min -1) Speed of output shaft (min -1) Max. engine output (kW) CG24EBSP / CG24EBS CG24EBDP / CG24EBD (SL) (S) (SL) (SLN) 23.9 NGK BMR7A 2800 – 3200 7600 0.8 23.9 NGK BMR7A 2800 – 3200 7600 0.8 23.9 NGK BMR7A 2800 – 3200 7600 0.8 23.
English Model Engine Displacement (cm3) Spark plug Idling speed (min -1) Speed of output shaft (min -1) Max. engine output (kW) CG27EBSP / CG27EBS CG27EBDP / CG27EBD (SL) (S) (SL) (SLN) 26.9 NGK BMR7A 2800 – 3200 7600 0.9 26.9 NGK BMR7A 2800 – 3200 7600 0.9 26.9 NGK BMR7A 2800 – 3200 7600 0.9 26.9 NGK BMR7A 2800 – 3200 7600 0.9 5.4 4.5 Fuel tank capacity (cm3) 520 Dry weight (kg) 5.2 5.
English Throttle wire / stop cord Press the upper tab (9) and open the air cleaner cover. (Fig. 6) Connect stop cords. (Fig. 7) If the throttle outer end (10) is threaded on your unit, screw it and the earth terminal (11) (if so equipped) into the cable adjuster stay (12) all the way, and then tighten this cable end using the adjuster nut (13) against the cable adjuster stay (12).
English ○ Fuel contains highly flammable and it is possible to get the serious personal injury when inhaling or spilling on your body. Always pay attention when handling fuel. Always have good ventilation when handling fuel inside building. Fuel ○ Always use branded 89 octane unleaded gasoline. ○ Use genuine two-cycle oil or use a mix between 25:1 to 50:1, please consult the oil bottle for the ratio or Hitachi Authorized Service Centers.
English WARNING When the engine is idling the cutting attachment must under no circumstances rotate. Air filter (Fig. 29) The air filter must be cleaned from dust and dirt in order to avoid: ○ Carburetor malfunctions ○ Starting problems ○ Engine power reduction ○ Unnecessary wear on the engine parts ○ Abnormal fuel consumption Clean the air filter daily or more often if working in exceptionally dusty areas. Cleaning the air filter Open the air filter cover and the filter (28). Rinse it in warm soap suds.
English List of recommended accessories 5” Manual line feed CG27EBSP (S) CG27EBS (S) CG24EBDP (SL) CG24EBD (SL) CG27EBDP (SL) CG27EBD (SL) ● ● ● ● ● ● ● ● ● ● ● ● 2.2 – 3.0 NYLON HEAD CH-100 NYLON HEAD CH-300 (W/CUTTER HOLDER CAP) CG24EBSP (S) CG24EBS (S) Pre-Cut Line TAP & GO NYLON HEADS BLADES ● ● ● ● ● ● 2.2 – 2.7 NYLON HEAD CH-300 L M10 x 1.25 Nut L M8 x 1.
English TROUBLESHOOTING Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your dealer or the Hitachi Authorized Service Center.
Deutsch (Übersetzung der Original-Gebrauchsanweisung) SYMBOLBEDEUTUNGEN HINWEIS: Nicht alle Geräte sind mit diesen Symbolen versehen. Symbole WARNUNG Die folgenden Symbole werden für diese Maschine verwendet. Achten Sie darauf, diese vor der Verwendung zu verstehen. Es ist wichtig, dass Sie sich mit den nachfolgenden Vorsichtsmaßnahmen und Warnungen vertraut machen und diese befolgen. Unvorsichtige oder unsachgemäße Handhabung des Geräts kann schwere oder tödliche Verletzungen zur Folge haben.
Deutsch TEILEBEZEICHNUNGEN 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24.
Deutsch WARN- UND SICHERHEITSHINWEISE Bedienersicherheit ○ Immer einen Gesichtsschutz bzw. eine Schutzbrille tragen. ○ Tragen Sie immer dicke, lange Hosen, rutschfeste Schuhe und Handschuhe. Das Arbeiten mit lockerer Kleidung, Schmuck, kurzen Hosen, Sandalen oder barfuß ist zu vermeiden. Das Haar ist so zu sichern, dass es nicht bis zu den Schultern herunterhängt. ○ Das Gerät darf nicht von Personen bedient werden, die übermüdet oder krank sind oder unter Alkohol- oder Medikamenteneinfluss stehen.
Deutsch ○ Nur Original-Ersatzteile von Hitachi verwenden, wie vom Hersteller empfohlen. Transport und Lagerung ○ Das Gerät mit ausgeschaltetem Motor tragen und den Schalldämpfer vom Körper fernhalten. ○ Lassen Sie den Motor abkühlen und leeren Sie den Kraftstoff tank, bevor Sie ihn lagern oder transportieren. Sichern Sie die Maschine während des Transports, um zu verhindern, dass Kraftstoff verloren geht oder dass Schäden oder Verletzungen auftreten.
Deutsch Modell Motor Hubvolumen (cm3) Zündkerze Leerlaufdrehzahl (min -1) Drehzahl der Ausgangswelle (min -1) Max. Motorleistung (kW) CG27EBSP / CG27EBS (SL) (S) (SL) (SLN) 26,9 NGK BMR7A 2800 – 3200 7600 0,9 26,9 NGK BMR7A 2800 – 3200 7600 0,9 26,9 NGK BMR7A 2800 – 3200 7600 0,9 26,9 NGK BMR7A 2800 – 3200 7600 0,9 5,4 4,5 Kraftstoff tankvolumen (cm3) 520 Trockengewicht (kg) Schneid-Vorsatzgerät CG27EBDP / CG27EBD 5,2 Typ / Durchm.
Deutsch (2) Fahrradgriff-Typ ((S) Modell) Den Griffhalter (7) von der Einheit entfernen. (Abb. 4) Den Griff einsetzen und den Griffhalter mit vier Schrauben locker befestigen. Den Winkel je nach Bedarf ausrichten. Dann die Schrauben festziehen. Das Schutzrohr mit Hilfe von Kabelklemmen (8) an der Antriebswelle oder dem Griff befestigen. (Abb. 5) Gaszug / Stoppkabel Drücken Sie die obere Lasche (9) und öffnen Sie den Luftfilterdeckel. (Abb. 6) Die Stoppkabel anschließen. (Abb.
Deutsch ○ ○ Wenn Ihr Gerät mit einer Schutzabdeckung unter dem Schneidmesser ausgestattet ist, überprüfen Sie es vor dem Einsatz auf Abnutzung oder Risse. Wenn Beschädigungen oder Spuren von Abnutzung zu sehen sind, tauschen Sie es aus, denn es handelt sich um ein Verschleißteil. Beim Handhaben der Schneideklinge müssen Sie Handschuhe tragen. WARNUNG Benutzen Sie für Hitachi-Köpfe nur vom Hersteller empfohlene flexible, nicht metallische Züge. Metalldrähte oder Drahtseile sind keinesfalls zulässig.
Deutsch WARNUNG Schneidwerkzeug kann auch nach dem Ausschalten des Motors oder Freigeben des Leistungsreglers Verletzungen verursachen, solange es sich weiterdreht. Das Gerät nach dem Ausschalten des Motors erst am Boden abstellen, wenn das Schneidwerkzeug zum Stillstand gekommen ist. Halbautomatischer Schneidkopf ○ Betreiben Sie beim Schneiden die Maschine mit einer Drehzahl von mehr als 6500 min -1. Eine übermäßig lange Verwendung bei niedriger Drehzahl kann zum vorzeitigen Verschleiß der Kupplung führen.
Deutsch (3) Den neuen Nylonfaden, wie in der Abbildung gezeigt, ungefähr auf die Hälfte zusammenlegen. Die u-förmige Schlaufe der Nylonschnur in der Führungsnut (30) an der Trennwand in der Spulenmitte einhaken. Eine Seite des Kabels sollte etwa 10 cm länger als die andere Seite sein. Beide Fadenhälften in derselben Richtung auf die Spule aufwickeln und darauf achten, dass jede Hälfte auf ihrer Seite der Trennwand bleibt. (Abb.
Deutsch Liste der empfohlenen Zubehörteile NYLONKOPF CH-300 (MIT MESSERHALTEKAPPE) 5” Manueller Fadenvorschub CG24EBDP (SL) CG24EBD (SL) CG27EBDP (SL) CG27EBD (SL) NYLONKOPF CH-100 CG27EBSP (S) CG27EBS (S) 2,2 – 3,0 CG24EBSP (S) CG24EBS (S) Vorgeschnittener Faden ● ● ● ● ● ● ● ● ● ● ● ● TAP & GO NYLONKÖPFE MESSER ● ● ● ● ● ● 2,2 – 2,7 NYLONKOPF CH-300 L M10 x 1,25 Mutter L M8 x 1,25 MEHRZWECK CG27EBSP (SL) CG27EBS (SL) 4” FAHRRADGRIFF CG24EBSP (SL) CG24EBS (SL) ALUMINIU
Deutsch FEHLERSUCHE UND -BESEITIGUNG Führen Sie die in der folgenden Tabelle aufgeführten Inspektionen durch, wenn das Gerät nicht ordnungsgemäß funktioniert. Kann das Problem dadurch nicht behoben werden, wenden Sie sich an Ihren Händler oder ein autorisiertes Hitachi-Kundendienstzentrum.
Français (Traduction des instructions d'origine) SIGNIFICATION DES SYMBOLES REMARQUE: Certains appareils n’en sont pas pourvus. Symboles ATTENTION Les symboles suivants sont utilisés pour l’outil. Bien se familiariser avec leur signification avant d’utiliser l’outil. Il est essentiel de lire et de comprendre parfaitement les consignes de sécurité et autres avertissements suivants. Vous devez les observer strictement.
Français DESCRIPTION 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24.
Français PRÉCAUTIONS ET CONSIGNES DE SÉCURITÉ Sécurité de l’utilisateur ○ Portez toujours une visière et des lunettes de protection. ○ Portez toujours un pantalon, des chaussures et des gants de sécurité antidérapants. Évitez les vêtements amples, les shorts, les sandales et les pieds nus. Veillez à ce que vos cheveux ne descendent pas au-dessous des épaules. ○ Utilisez cette machine uniquement si vous êtes en pleine possession de vos moyens physiques.
Français ○ Utilisez uniquement les pièces de rechange d’origine Hitachi. Transport et rangement ○ Portez la machine avec moteur arrêté et silencieux orienté vers l’extérieur. ○ Laisser le moteur refroidir, vider le réservoir de carburant avant le rangement ou le transport. Bien attacher la machine pendant le transport pour éviter des pertes de carburant, des dommages ou des blessures. ○ Vidangez le réservoir de carburant avant de ranger la machine. Cette opération est recommandée après chaque utilisation.
Français Modèle Moteur Cylindrée (cm3) Bougie d’allumage Ralenti (min -1) Vitesse de l’arbre de sortie (min -1) Puissance max du moteur (kW) CG27EBSP / CG27EBS (SL) (S) (SL) (SLN) 26,9 NGK BMR7A 2800 – 3200 7600 0,9 26,9 NGK BMR7A 2800 – 3200 7600 0,9 26,9 NGK BMR7A 2800 – 3200 7600 0,9 26,9 NGK BMR7A 2800 – 3200 7600 0,9 5,4 4,5 Contenance du réservoir de carburant (cm3) Poids à sec (kg) CG27EBDP / CG27EBD 520 5,2 5,4 Cordon en nylon Cordon en nylon Lame en métal (255) Cordon en nylon
Français (2) Type de poignée de vélo (modèle (S)) Démontez le support de poignée (7). (Fig. 4) Ajustez les poignées puis serrez légèrement le support de poignée à l’aide des quatre vis. Réglez selon la position appropriée. Fixez ensuite fermement au moyen des vis. Fixez le tube de protection au tube de transmission ou à la poignée à l’aide des colliers de cordon (8). (Fig. 5) Câble de commande des gaz / câble de marche-arrêt Appuyez sur l’onglet supérieur (9) et ouvrez le couvercle du filtre à air. (Fig.
Français IMPORTANT ○ Avant utilisation, assurez-vous que la lame a été bien installée. ○ Si votre machine est équipée d’une couverture de protection sous la lame de coupe, assurez-vous qu’elle ne présente aucune usure excessive ou fissure avant utilisation. En cas de dommage ou d’usure, remplacez-la. ○ Veillez à bien porter des gants lors de la manipulation de la lame de coupe. ATTENTION Utilisez uniquement des fils non métalliques recommandés par le fabricant pour les têtes Hitachi.
Français Tête de coupe semi-automatique ○ Faites fonctionner le moteur à un régime supérieur à 6 500 min -1 lors du débroussaillage. L’utilisation prolongée de la machine au ralenti peut aboutir à une usure prématurée de l’embrayage. ○ Coupez l’herbe de la droite vers la gauche. ATTENTION L’outil de coupe peut blesser lorsqu’il continue de tourner après l’arrêt du moteur ou lorsque l’on déclenche la commande d’alimentation du moteur.
Français (5) Insérez les deux bouts libres du fil dans le guide-cordon (32) lorsque vous placez la bobine dans le boîtier. (Fig. 36) REMARQUE Lors de la mise en place d’une bobine dans le boîtier, essayez d’aligner les trous d’arrêt (31) sur le guide-cordon (32) pour faciliter le dégagement ultérieur du fil. (6) Placez le couvercle sur le boîtier de façon à ce que les attaches de blocage (33) sur le boîtier rencontrent les longs trous (34) sur le couvercle.
Français Liste des accessoires recommandés TÊTE EN NYLON CH-300 (AVEC COUVERCLE DE PORTE-LAME) 5” LAMES TÊTEs EN NYLON TAP & GO TÊTE EN NYLON CH-300 Alimentation de ligne manuelle CG27EBDP (SL) CG27EBD (SL) TÊTE EN NYLON CH-100 CG24EBDP (SL) CG24EBD (SL) 2,2 – 3,0 CG27EBSP (S) CG27EBS (S) Ligne de précoupe CG24EBSP (S) CG24EBS (S) TÊTE EN NYLON CH-100 (Avec LIGNE EN NYLON) MULTI-USAGE CG27EBSP (SL) CG27EBS (SL) Épaisseur de lame (mm) ou Diamètre de ligne de coupe (mm) 4” Nom POIGNÉE DE V
Français DÉPANNAGE Consulter le tableau d’inspection ci-après si l’outil ne fonctionne pas correctement. Si le problème n’est pas réglé, veuillez vous adresser au concessionnaire ou à un centre de réparations Hitachi. Condition Cause Le réservoir à carburant est vide ou presque vide Le réservoir à carburant contient un vieux carburant (odeur agressive). Système de carburant Trop de carburant a été absorbé et la bougie est noyée. Le filtre à carburant est bouché par les saletés.
Italiano (Traduzione delle istruzioni originali) SIGNIFICATI DEI SIMBOLI NOTA: Alcune unità non ne sono provviste. Simboli ATTENZIONE Di seguito mostriamo i simboli usati per la macchina. Assicurarsi di comprenderne il significato prima dell’uso. È importante leggere, comprendere a fondo e osservare le precauzioni di sicurezza e le avvertenze di seguito riportate. Disattenzione e l’uso improprio dell’unità possono divenire causa di lesioni gravi o anche fatali.
Italiano DESCRIZIONE DELLE VARIE PARTI 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24.
Italiano AVVERTENZE E ISTRUZIONI PER LA SICUREZZA Sicurezza dell’operatore ○ Durante il taglio si deve sempre indossare una protezione completa per il viso o almeno per gli occhi. ○ Indossare sempre pantaloni lunghi e pesanti, stivali antiscivolo e guanti. Non si deve indossare abbigliamento eccessivamente largo né gioielli, pantaloni corti e sandali, né tantomeno a piedi nudi. I capelli devono essere raccolti affinché rimangano sopra le spalle.
Italiano ○ Si devono usare esclusivamente i ricambi originali Hitachi raccomandati dal costruttore della macchina. Trasporto e conservazione ○ L’unità/macchina deve essere trasportata a mano con il motore spento e la marmitta tenuta ben lontana dal corpo. ○ Lasciar raffreddare il motore, quindi svuotare il serbatoio del carburante prima di conservare o trasportare. Fissare la macchina durante il trasporto per evitare la perdita di carburante, danni o lesioni.
Italiano Modello Motore Cilindrata (cm3) Candela di accensione Regime minimo del motore (min -1) Velocità dell’albero di uscita (min -1) Max. potenza motore (kW) CG27EBSP / CG27EBS (SL) (S) (SL) (SLN) 26,9 NGK BMR7A 2800 – 3200 7600 0,9 26,9 NGK BMR7A 2800 – 3200 7600 0,9 26,9 NGK BMR7A 2800 – 3200 7600 0,9 26,9 NGK BMR7A 2800 – 3200 7600 0,9 5,4 4,5 Capacità del serbatoio del carburante (cm3) Peso a secco (kg) Del dispositivo di taglio 520 5,2 Tipo / diametro.
Italiano PROCEDURE DI MONTAGGIO Installazione della protezione del dispositivo di taglio (Fig. 10 – 12) Montaggio dell’albero trasmissione al motore (Fig. 1) Allentare il bullone di bloccaggio del tubo (1) di dieci giri approssimativamente, affinché la punta del bullone non ostacoli l’inserimento del tubo dell’albero di trasmissione.
Italiano ○ 3. ○ Se la testina di taglio non alimenta correttamente la linea di taglio, verificare che il filo di nylon e tutti i componenti siano installati correttamente. In caso di bisogno ci si può rivolgere ad un Centro di Assistenza Autorizzato Hitachi. Installazione (Fig. 14) Installare la testa di taglio sulla scatola ingranaggi dei bordatori/ decespugliatori. Il dado di montaggio ha una filettatura a sinistra. Ruotare in senso orario per allentare/in senso antiorario per serrare.
Italiano La spinta della lama può verificarsi quando la lama rotante tocca un oggetto solido nell’area critica. Può avvenire una reazione pericolosa a causa della quale l’intera unità e l’operatore possono subire una violenta spinta. Questa reazione è detta spinta della lama. Come risultato di ciò, l’operatore può perdere il controllo dell’unità, il che può causare lesioni gravi o fatali. La spinta della lama può verificarsi con maggiore probabilità in aree in cui è difficile vedere il materiale da tagliare.
Italiano NOTA In alcune zone le norme locali richiedono l’impiego di una candela a resistore per sopprimere il rumore elettromagnetico causato dalla scintilla di accensione. Se questa macchina era originariamente dotata di una candela a resistore, in caso di sostituzione se ne deve usare una di tipo analogo. Coppia conica (Fig.
Italiano Elenco di accessori raccomandati TESTINA IN NYLON CH-300 (CON PIASTRINA FERMADISCO) 5” Avanzamento manuale del filo CG27EBDP (SL) CG27EBD (SL) TESTINA IN NYLON CH-100 CG24EBDP (SL) CG24EBD (SL) 2,2 – 3,0 CG27EBSP (S) CG27EBS (S) Filo pretagliato ● ● ● ● ● ● ● ● ● ● ● ● TESTINE AUTOMATICHE LAME ● ● ● ● ● ● 2,2 – 2,7 TESTINA IN NYLON CH-300 Dado L M10 x 1,25 L M8 x 1,25 MULTIUSO CG24EBSP (S) CG24EBS (S) TESTINA IN NYLON CH-100 (CON FILO IN NYLON) IMPUGNATURA DA BICI
Italiano RISOLUZIONE DEI GUASTI Usare le ispezioni nella tabella di seguito se l’utensile non funziona normalmente. Se questo non risolve il problema, consultare il proprio rivenditore o Centro di Assistenza Autorizzato Hitachi.
(Vertaling van de oorspronkelijke aanwijzingen) Nederlands BETEKENIS VAN DE SYMBOLEN OPMERKING: Sommige machines zijn hier niet van voorzien. Symbolen WAARSCHUWING Hieronder staan symbolen afgebeeld die van toepassing zijn op deze machine. U moet de betekenis hiervan begrijpen voor gebruik. Het is belangrijk dat u de volgende veiligheidsaanwijzingen en waarschuwingen leest, goed begrijpt en opvolgt. Nalatig of onjuist gebruik van de machine kan ernstig of zelfs dodelijk letsel veroorzaken.
Nederlands WAT IS WAT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24.
Nederlands Niet-goedgekeurde wijzigingen en/of accessoires kunnen leiden tot ernstig persoonlijk letsel, of zelfs de dood van de gebruiker of anderen. WAARSCHUWINGEN EN VEILIGHEIDSINSTRUCTIES ○ Veiligheid van de gebruiker ○ Draag altijd een vizier of veiligheidsbril. ○ Draag altijd een dikke, lange broek, niet slippende laarzen en handschoenen. Draag geen loszittende kleding, sieraden, een korte broek, sandalen en werk nooit blootsvoets. Draag lang haar samengebonden zodat het maximaal schouderlang is.
Nederlands Vervoer en opslag ○ Draag de machine alleen wanneer de motor gestopt is en met de uitlaat weg van uw lichaam. ○ Laat de motor afkoelen, leeg de brandstoftank voorafgaand aan opslag of transport. Beveilig de machine tijdens transport om het verlies van brandstof, schade en letsel te voorkomen. ○ Maak de brandstoftank helemaal leeg voor u de machine opbergt. We raden u aan de tank elke keer nadat u de machine gebruikt heeft, leeg te maken.
Nederlands Model Motor Cilinderinhoud (cm3) Bougie Snelheid in vrijstand (min -1) Max. toerental (min -1) Toerental van uitgaande as (min -1) Max.
Nederlands OPMERKING Als er een handvatlabel op de aandrijfasbehuizing van uw machine is, volg dan de aanwijzing op het label. (2) Fietshandvat type ((S) model) Verwijder de handvatklem (7) van de machine. (Afb. 4) Plaats de handvaten en bevestig de handvatklem lichtjes met de vier schroeven. Breng in de juiste positie. Draai de schroeven vervolgens stevig vast. Bevestig de beschermhuls aan de aandrijfas of het handvat met de snoerklemmen (8). (Afb.
Nederlands LET OP ○ Controleer of het mesblad correct gemonteerd is voordat u aan het werk gaat. ○ Als uw machine is voorzien van een beschermkap onder het mesblad, controleer deze dan op slijtage en scheuren voordat u aan het werk gaat. Als er slijtage of beschadiging wordt vastgesteld, moet de beschermkap worden vervangen omdat dit een slijtage-onderdeel is. ○ Draag handschoenen bij het omgaan met het mesblad.
Nederlands WAARSCHUWING Snijgereedschap kan verwondingen veroorzaken omdat het nog draait nadat de motor is gestopt of de vermogensregeling uit is. Wanneer de machine uit wordt gezet, moet u controleren of het snijgereedschap inderdaad helemaal gestopt is voordat u de machine neerzet. Automatisch toevoeren van meer nylon snijdraad wanneer tegen de snijkop wordt geklopt bij laag toerental (niet hoger dan 4500 min -1).
Nederlands (7) De eerste snijlengte van het snoer moet ongeveer 11–14 cm zijn en dient aan beide kanten gelijk te zijn. (Afb. 38) Mesblad (Afb. 39) WAARSCHUWING Draag beschermende handschoenen als u het mesblad aanraakt of onderhoudt. ○ ○ ○ ○ ○ ○ ○ Gebruik een scherp mesblad. Een bot mesblad gaat eerder vast of klem zitten. Vervang de bevestigingsmoer als deze beschadigd is en moelijk vastgedraaid kan worden.
Nederlands Lijst met aanbevolen accessoires NYLONKOP CH-300 (M/SNIJDER HOUDER DOP) 5” Handmatige draadtoevoer CG27EBSP (S) CG27EBS (S) CG24EBDP (SL) CG24EBD (SL) CG27EBDP (SL) CG27EBD (SL) NYLONKOP CH-100 CG24EBSP (S) CG24EBS (S) 2,2 – 3,0 ● ● ● ● ● ● ● ● ● ● ● ● TAP & GO NYLONKOPPEN MESSEN ● ● ● ● ● ● 2,2 – 2,7 NYLONKOP CH-300 L M10 x 1,25 moer L M8 x 1,25 MULTIFUNCTIONEEL CG27EBSP (SL) CG27EBS (SL) Voorgesneden draad FIETSSTUURHANDGREEP CG24EBSP (SL) CG24EBS (SL) Mesdi
Nederlands OPLOSSEN VAN PROBLEMEN Voer de inspecties in onderstaande tabel uit als het gereedschap niet normaal werkt. Als dit het probleem niet oplost, contact opnemen met uw dealer of het erkende Hitachi onderhoudscentrum. Probleem Oorzaak De brandstoftank is leeg of bijna leeg Er zit oude brandstof in de tank (ruikt niet goed meer) Brandstofsysteem Er wordt teveel brandstof verstoven en de bougie is nat Het brandstoffilter zit verstopt De brandstofleiding is geknikt of losgekoppeld De motor start niet.
Español (Traducción de las instrucciones originales) SIGNIFICADO DE LOS SÍMBOLOS NOTA: Algunos aparatos no están provistos de ellos. Símbolos ADVERTENCIA A continuación se muestran los símbolos usados para la máquina. Asegúrese de comprender su significado antes del uso. Es importante que usted lea, entienda totalmente y observe las siguientes precauciones y advertencias de seguridad. El uso descuidado o incorrecto del aparato podrá causarle lesiones serias o fatales.
Español ¿QUÉ ES QUÉ? 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24.
Español ADVERTENCIAS E INSTRUCCIONES DE SEGURIDAD Seguridad del usuario ○ Utilice siempre protecciones como caretas o gafas de seguridad. ○ Utilice siempre pantalones gruesos, botas antideslizantes y guantes. No utilice prendas sueltas, joyas, pantalones cortos o sandalias, y nunca trabaje descalzo. Recójase el pelo de forma que quede por encima del hombro. ○ No opere este aparato si está cansado, enfermo o bajo la influencia del alcohol, drogas o medicamentos.
Español Transporte y almacenamiento ○ Transporte el aparato con el motor y el silenciador a una distancia segura del cuerpo. ○ Permita que el motor se enfríe, y vacíe el depósito de combustible antes del almacenamiento o transporte. Asegure la máquina durante el transporte para prevenir pérdidas de combustible, daños o lesiones. ○ Vacíe el depósito de combustible antes de guardar el aparato. Se recomienda vaciar el depósito de combustible cada vez que termine de utilizar el aparato.
Español Modelo Motor Desplazamiento (cm3) Bujía Velocidad de ralentí (min -1) Velocidad del eje de salida (min -1) Potencia máx.
Español Acople el asidero al tubo del eje de distribución en ángulo con el motor. Ajuste su posición de la manera que le resulte más cómoda antes de ponerlo en funcionamiento. NOTA Si su aparato tiene una etiqueta que muestre la ubicación del asidero en el tubo del eje de distribución, siga su ilustración. (2) Tipo de mango Bike (modelo (S)) Retire la abrazadera del asidero (7) del conjunto. (Fig. 4) Coloque los asideros y acople la abrazadera del asidero ajustándola suavemente con cuatro tornillos.
Español NOTA ○ Cuando instale la tapa de soporte de la cuchilla (21), asegúrese de colocar la parte cóncava hacia arriba. ○ Presione la clavija de tope (20) de la transmisión en ángulo para bloquear el soporte de la cuchilla (22). Tenga en cuenta que el tornillo o tuerca de fijación de la cuchilla (23) está roscado a izquierdas (se afloja en el sentido de las agujas del reloj y se aprieta en el sentido contrario). Apriete el tornillo o tuerca de fijación con la llave de vaso.
Español ADVERTENCIA El mecanismo de corte puede provocar lesiones mientras gira tras haber detenido el motor o haber apagado el control de la alimentación. Cuando el aparato esté apagado, asegúrese de que el mecanismo de corte se ha detenido antes de apoyarlo sobre el suelo. ○ ○ Desgaste innecesario de las piezas del motor Consumo excesivo de combustible Limpie el filtro de aire diariamente o con mayor frecuencia cuando trabaje en zonas con gran cantidad de polvo.
Español (4) Pulse cada línea en los orificios del tope (31), dejando los extremos sueltos aprox. 10 cm de largo. (Fig. 35) (5) Introduzca ambos extremos sueltos de la línea a través de la guía de cuerda (32) cuando coloque el rollo en la caja. (Fig. 36) NOTA Cuando coloque un rollo en la caja, intente alinear los orificios del tope (31) con la guía del cable (32) para poder soltar luego la línea de corte más facilmente.
Español Lista de accesorios recomendados CABEZAL DE NYLON CH-300 (CON TAPA DEL SOPORTE DE LA CUCHILLA) 5” Alimentación de línea manual CG24EBSP (S) CG24EBS (S) CG27EBSP (S) CG27EBS (S) CG24EBDP (SL) CG24EBD (SL) CG27EBDP (SL) CG27EBD (SL) CABEZAL DE NYLON CH-100 Línea de corte previo ● ● ● ● ● ● ● ● ● ● ● ● 2,2 – 3,0 ● ● ● ● ● ● 2,2 – 2,7 CABEZAL DE NYLON CH-300 Tuerca I M10 x 1,25 I M8 x 1,25 MULTIUSO CG27EBSP (SL) CG27EBS (SL) 4” ASA TIPO MANILLAR CG24EBSP (SL) CG24EBS
Español SOLUCIÓN DE PROBLEMAS Siga las instrucciones que se indican en la siguiente tabla si la herramienta no funciona normalmente. Si esto no soluciona el problema, consulte a su distribuidor o al centro de servicio autorizado de Hitachi.
Português (Tradução das instruções originais) SIGNIFICADO DOS SÍMBOLOS NOTA: Os símbolos referidos não se encontram em todos os modelos. Símbolos ADVERTÊNCIA A seguir aparecem os símbolos utilizados pela máquina. Assimile bem seus significados antes do uso. É importante que leia, compreenda integralmente e respeite as seguintes precauções e advertências de segurança. O uso do aparelho de forma incorrecta ou sem os cuidados necessários pode causar lesões graves ou até fatais.
Português DESCRIÇÃO DE CADA COMPONENTE 1. Tampão de combustível 2. Gatilho do acelerador 3. Punho de arranque 4. Protecção do acessório de corte 5. Acessório de corte 6. Tubo do veio de transmissão 7. Pega 8. Olhal de suspensão 9. Interruptor de ignição 10. Gancho 11. Trava do gatilho do acelerador 12. Alavanca do ar 13. Motor 14. Ângulo da transmissão 15. Caixa de juntas 16. Chave combinada 17. Chave de porcas (se equipada) 18. Chave de barra sextavada 19. Tampa da lâmina (se equipada) 20.
Português ADVERTÊNCIAS E INSTRUÇÕES DE SEGURANÇA Segurança do operador ○ Use sempre uma viseira ou óculos de protecção. ○ Utilize sempre calças compridas e reforçadas e botas e luvas anti-derrapantes. Não use roupas folgadas, jóias e bijutaria, calções curtos, sandálias e nunca trabalhe descalço. Prenda o cabelo para este não cair por cima dos ombros. ○ Não use este aparelho quando estiver cansado, doente ou sob efeitos de álcool, drogas ou medicamentos.
Português ○ ○ ○ ○ ○ ○ ○ Deixe o motor arrefecer, esvazie o depósito de combustível antes de armazenar ou transportar. Prenda a máquina de forma segura durante o transporte para prevenir perda de combustível, danos ou lesões. Esvazie o depósito de combustível antes de guardar o aparelho. É recomendável esvaziar o depósito de combustível após cada uso. No caso de deixar o combustível no depósito, guarde o aparelho de forma que não haja vazamento de combustível.
Português Modelo Motor Cilindrada (cm3) Vela de ignição Velocidade de ralenti (min -1) Velocidade do eixo de saída (min -1) Potência máxima do motor (kW) CG27EBSP / CG27EBS (SL) (S) (SL) (SLN) 26,9 NGK BMR7A 2800 – 3200 7600 0,9 26,9 NGK BMR7A 2800 – 3200 7600 0,9 26,9 NGK BMR7A 2800 – 3200 7600 0,9 26,9 NGK BMR7A 2800 – 3200 7600 0,9 5,4 4,5 Capacidade do depósito de combustíve (cm 3) Peso a seco (kg) Acessório de corte 520 5,2 Tipo / Diâm.
Português (2) Tipo de punho de bicicleta (modelo (S)) Retire o suporte da pega (7) do conjunto. (Fig. 4) Coloque as pegas e fixe ligeiramente o suporte da pega com quatro parafusos. Ajuste para a posição adequada. De seguida, fixe-a firmemente com os parafusos. Coloque o tubo de protecção no veio de transmissão ou pega utilizando grampos de cabos (8). (Fig. 5) Cabo do acelerador/cabo de paragem Prima a patilha superior (9) e abra a tampa do filtro de ar. (Fig. 6) Ligue os cabos de paragem. (Fig.
Português PRECAUÇÃO ○ Antes de utilizar, certifique-se de que a lâmina foi correctamente instalada. ○ Se a sua unidade estiver equipada com a tampa de protecção debaixo de uma lâmina de corte, verifique a existência de desgaste ou rachadelas, antes de utilizar. Se existirem danos ou desgaste, substitua-a, uma vez que é um artigo consumível. ○ Necessita utilizar um par de luvas quando manusear a lâmina de corte.
Português ADVERTÊNCIA Um acessório de corte pode magoar se continuar a rodar depois de o motor parar ou se o controlo de potência for libertado. Depois de desligar o aparelho, certifique-se de que o mecanismo de corte tenha parado antes de pousar a serra. Alimenta automaticamente mais linha de corte de nylon quando é batida a baixas rpm (inferiores a 4500 min-1).
Português Lâmina (Fig. 39) ADVERTÊNCIA Use luvas de protecção quando manusear ou efectuar manutenção na lâmina. ○ ○ ○ ○ ○ ○ ○ Utilize uma lâmina afiada. Uma lâmina romba pode encravar e provocar ressaltos. Substitua a porca de aperto se estiver danificada e for difícil apertar. Quando substituir a lâmina, adquira uma recomendada pela Hitachi, com um orifício de fixação de 25,4 mm. Em caso de uma lâmina de 3 dentes (35), pode ser utilizado em ambos os lados.
Português Lista de acessórios recomendados LÂMINAS LINHAS DE NYLON DE BATER E FUNCIONAR LINHA DE CORTE DE NYLON CH-300 (COM TAMPA DO SUPORTE DO CORTADOR) 5” LINHA DE CORTE DE NYLON CH-300 Alimentação manual da linha CG27EBSP (S) CG27EBS (S) CG24EBDP (SL) CG24EBD (SL) CG27EBDP (SL) CG27EBD (SL) LINHA DE CORTE DE NYLON CH-100 CG24EBSP (S) CG24EBS (S) Linha précortada FINALIDADE MÚLTIPLA CG27EBSP (SL) CG27EBS (SL) LINHA DE CORTE DE NYLON CH-100 (COM LINHA DE NYLON) PEGA TIPO GUIADOR CG24EBSP (
Português RESOLUÇÃO DE PROBLEMAS Utilize as inspecções na tabela abaixo, caso a ferramenta não funcione normalmente. Se isto não solucionar o problema, consulte o seu representante ou o Centro de Serviço Autorizado da Hitachi. Condição Causa O depósito de combustível está vazio ou o nível de combustível está baixo. O depósito de combustível contém combustível velho (odor desagravável). Sistema de combustível Demasiado combustível é absorvido, molhando a vela de ignição.
000Book_CG24EBSP(SL)_WE.
000Book_CG24EBSP(SL)_WE.
000Book_CG24EBSP(SL)_WE.
000Book_CG24EBSP(SL)_WE.
000Book_CG24EBSP(SL)_WE.
000Book_CG24EBSP(SL)_WE.
000Book_CG24EBSP(SL)_WE.
000Book_CG24EBSP(SL)_WE.
000Book_CG24EBSP(SL)_WE.
English Italiano Object of declaration: Hitachi Grass Trimmer/Brush Cutter CG24EBSP(SL), CG24EBSP(S), CG24EBS(SL), CG24EBS(S), CG24EBDP(SL), CG24EBDP(SLN), CG24EBD(SL), CG24EBD(SLN), CG27EBSP(SL), CG27EBSP(S), CG27EBS(SL), CG27EBS(S), CG27EBDP(SL), CG27EBDP(SLN), CG27EBD(SL), CG27EBD(SLN) Oggetto della dichiarazione: Hitachi Bordatore/Decespugliatore, CG24EBSP(SL), CG24EBSP(S), CG24EBS(SL), CG24EBS(S), CG24EBDP(SL), CG24EBDP(SLN), CG24EBD(SL), CG24EBD(SLN), CG27EBSP(SL), CG27EBSP(S), CG27EBS(SL), CG27EBS
Português Objeto de declaração: Hitachi Foice a motor/Roçadora, CG24EBSP(SL), CG24EBSP(S), CG24EBS(SL), CG24EBS(S), CG24EBDP(SL), CG24EBDP(SLN), CG24EBD(SL), CG24EBD(SLN), CG27EBSP(SL), CG27EBSP(S), CG27EBS(SL), CG27EBS(S), CG27EBDP(SL), CG27EBDP(SLN), CG27EBD(SL), CG27EBD(SLN) DECLARAÇÃO DE CONFORMIDADE CE (Aplica-se apenas à Europa) Declaramos sob nossa exclusiva responsabilidade que este produto está em conformidade com as diretivas 2006/42/CE, 2014/30/UE e 2000/14/CE.