COLOUR MONITOR FARBMONITOR MONITOR EN COLOR MONITOR A COLORI MONIIEUR COULEUR 141vlvxPliA CM1484ME USER MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . page 2 BEDIENUNGSANLEITUNG 10 MANUAL DEL USUARIO ................ seite 18 INSTRUZIONI PER L’USO . . . . . . . . . . . . . . . . . . pag 24 MANUEL DE L’UTILISATEUR . . . . . . . . . . . . . . page 30 .= . . . . . . . . . . ..m.
I . NOTICE The information in this document is subject to change without notice. Hitachi assumea no responsibility for any errors that may appear in this document. Colour Monitor 14MVX Plus Operating Guide Features: The following features are provided with the HITACHI colour Monitor 14MVXPhS: Wide compatibility range of graphics standard, VGA, XGA, 8514/A, Super VGA, and Macintosh lIVideo Card. Sharp focus and remarkable display quality by new design CRT.
For U.K. Customers THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K. PLEASE REFER TO THE NOTES ON THIS PAGE. NOTE: ELECTRICAL CONNECTION Your monitor requires an electrical supply of 240 volts – 50 Hertz and shfkld be protected by a 5 amp fuse. Your equipment is supplied with a plug incorporating a 5 amp fuse fitted to the mains lead.
As the colours of the wires in your mains Iead in this equipment may not correspond with the markings identified with the terminals of your plug, proceed as follows: The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the symbol or coloured Green or Green and Yellow. The wire which which is marked is coloured Brown must be connected with the letter L or coloured Red.
@EIi@ NEVER REMOVE THE BACK COVER Removal of the back cover MUST be carried out only by quaMed personnel. This display monitor contains high voltages tilde. DO NOT USE IN HOSTILE ENVIRONMENTS DO NOT expose this d~lay monitor to rain or moisture to prevent electric shock or fwe hazard. This unit is designed to be used in the ofiice or home environment. DO NOT subject the unit to vibrations, dust, or corrosive gases.
@PERATmG> Controls Rear View Front View m. (7) (6) (5) (4) (3) (2) (1) J) (8) (1) Power Switch Use this switch to power ON or OFF by pressing it. When the power is ON, green light on the knob turns on to indicate. (2) Contrast Control ((D) Use this to set the foreground brightness cf the screen. (3) Brightness Control (-,, ] Use this to set the background to black. Most of the latest application software utilizes coloured background and this control is usually set at its maximum.
(6) Vertical Size [~] Adjust this contxol to the preferred height. (7) Vertical Position [Q 1 Adjust this to place the display at the centre of the screen. (8) Signal Cable Connect the end of the cable to your computer. (9) Power Cord Tn-let Connector Insert proper power cord here. BEFORE CONNECTING TEE MONITOR TO YOUR COMPUTER, MAKE SURE TEE POWER TO TEE MONITOR AND COMPUTER ARE TURNED OFF. 1. Connect the signal cable to your computer’s video output comector.
IP OMPATIBILITY) 14MVX Plus is compatible with: 1. IBM P S/2 series computers with MCGA, VGA, XGA and 85 14/A graphics standards. Signal cable is conilgured as IBM 8514 monitor. 2. Most of the VGA and Super VGA standard graphics boards available for the PC, PC/AT,PS/2 and EISA bus computers. Please ask your dealer for details. 3. Apple Macintosh II computer with Macintosh V]deo Card. You have to obtain a 15 pinto 15 pin converter from your dealer.
@PECIFIcATIO@) CRT 14(1 3V) inches diagonal, 0.28 mm dot pitch, Black B matrix, Silica coated, Short Persistence. Input Signal Video 0.7 Vpp Sync: Separate H,V or Composite H/V lTL level or Sync on Green at 0.3 Vpp. Synchronization Horizontal: 30 — 50 kHz Vertical: 50 —IOOHZ Automatically synchronize.
