HITACHI - -- -- --- -- USER MANUAL . . ..I BEDIENUNGSANLEITljNG . ..17 MANUAL DE USUARIO . ..31 CM1 711 MET-PCMP GEBRUIKSAANWIJZING . ..35 MANUEL UTILISATEUR . . .s COLOUR MONITOR with EasyMenu ! EasyMenu is HITACHI’s On Screen Display function for easy operation. READ THE INSTRUCTIONS INSIDE CAREFULLY. KEEP THIS USER MANUAL FOR FUTURE REFERENCE. For future reference, record the serial number of your colour monitor. SERIAL No. .-. The serial number is located on the rear of the monitor.
ENGE COLOUR MONITOR CM171 1 MET- I PCMP USER MANUAL NOTICE : The information in this document is subject to change without notice. The manufacturer assumes no responsibility for any errors that may appear in this manual. I FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . .
-ENG The provided USH Sharpest Focus and Highest Contrast by flat screen CRT with anti-glare, dynamic focus circuit, dark glass, and an INVAR shadow mask gives the sharpest focus and highest contrast to minimize eye fatigue. Wide-range Multi-Scanning Automatic scanning and automatic adjustment to conform with a wide range of scanning frequencies and user requirements. Digital Picture Control Function Position, size, pincushion, trapezoid and rotation are adjustable by digital controls.
! NEVER REMOVE THE REAR COVER I ENGZ USH = The rear cover MUST be removed only by authorized service personnel. This colour monitor contains high voltage components. ! BE CAREFUL OF STATIC ELECTRICITY ON CRT SURFACE ! To prevent electrical shock by the static electricity on the CRT surface, disconnect the power cord at least 30 SECONDS AFTER turning off the power.
EF;z Install the monitor in the following way, taking care to maintain safety. 1. Installation Install the monitor on a horizontal base. Front Cover CRT Surface Tilt & Swivel Base I FRONT VIEW Rear Cover AC Inlet -I Signal Input CoYector I REAR VIEW A NOTICE INSTALL THE UNIT IN ADEQUATE ENVIRONMENT ! DO NOT expose this monitor to rain or moisture to prevent electric shock or fire hazard. This unit is designed to be used in an office or business environment.
KEEP IN A WELL VENTILATED PLACE ! DO NOT cover this monitor or place anything against any sides (not only top, right and left side but also rear and bottom side) of unit. Ventilation holes are provided at all sides of the rear cover to prevent the temperature from rising. KEEP AWAY FROM HEATING RADIATION OR SOURCE ! AVOID placing the unit in direct sunshine or near a heating appliance.
A FOR THE CUSTOMERS IN U.K. =ENG - USH THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K. PLEASE REFER TO THE NOTES ON THIS PAGE. IMPORTANT FOR UNITED KINGDOM WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug.
3. Signal Input Connection Connect the Signal Input Connector to the D-Sub Mini IBpin signal output terminal of the host computer. ENGe LISH - to the host computer b’ QIg +@- Signal Input Connector l , REAR VIEW If the graphics board supplies more than one type of sync. signal, the sync. signal type will be automatically selected by the monitor, with the priority shown in the following table. 4. Power On Turn on the Power Switch of the monitor first, then the computer.
l Microprocessor-based preset functions can store 20 sets of geometry settings including the standard settings. Below listed preset modes. The following industrial standard settings have been preprogrammed by the factory. NOTE w Input signals with approximately the same frequencies may be regarded as the same signal. n The following horizontal timing conditions are recommended. Horizontal front porch should be more than 0.1 us. Horizontal sync. width should be more than 1 .O us.
- Control Panel p Power LED -Function LED ‘p--l~Jj F”t;;;N [-=-g-J +fOR~ Switches I I I page 12 “STORE ..i F&T-J ffy ADJUST Switches @ I DEGAUSS Switch I I Page s-t I ‘ADJUSTMENT = -O Pagb9 Page 9 ‘DEGAUSSING ‘POWER ON/OFF” I POWER ON/OFF l Press the POWER switch 0, to switch the power ON/OFF. Dal &2 H When power is ON, the Power LED lights on green. DEGAUSSING E!?!!? a Press the DEGAUSS switch, to degauss manually.
ADJUSTMENT (others) =aNG - USH l a You can adjust the items shown in the following ._ table, as show; below. 1. Press the FUNCTION switch. The Function ~~~ LED will light, and the EasyMenu will appear. 2. Select the item by the SELECT switches. The selected item is indicated by magenta icon on the EasyMenu. Qr-$o 3. Adjust the selected item by the ADJUST h . switches. n You can store the adjusted condition. Refer to Page 12 ‘STORE”.
‘:.U” for Colour Select is not available before an adjustment is made by the user. There are no factory settings of selects the previous colour mode ‘.-.U”. Refer to Page 17 ‘STORE”. B’ makes the selected colour weaker. n When the selected colour reached to its maximum or minimum end and you still need to adjust the colour, adjust the other two colours to the other direction.
STORE -:;f l Press the STORE switch, to store the currently adjusting data as follows STORED fnllnwc Item H.Position H.Size V. Position V.Size Pincushion Trapezoid Storing Condition Restoring Condition One setting is allowed for each video mode. When the monitor detects You can store maximum 20 sets of geometry the same video mode. settings including the standard settings (refer to page 8 “STANDARD SETTINGS”).
SIGNAL STATUS l When the monitor has detected the change of the signal input condition, the monitor will indicate the condition automatically, as follows. Condition I Indication I LISH - Sample of ‘EasyMenu” I When the monitor detects proper signal. The EasyMenu indicates the horizontal frequency and vertical frequency. 1 Precision frequency, Horizontal approximately it 1 kHz *2Hz Vertical approximately N Provided the Signal Status Display function is set to ON.
Et;f l This monitor complies with VESA, Nutek, and Energy Star power saving requirements. The power saving system works only when used with VESA DPMS compliant PC’s and/or graphic controllers. e This monitor complies with VESA DDC1/2B specifications. Plug & Play is a system with computer, peripherals (including monitors), and operating system. It works when the monitor is connected to DDC ready computer that is running an operating system software that is capable for the plug & play.
CRT 17 inches picture tube, Anti-Reflection coat, 0.22 mm (optional 0.24 mm) horizontal dot pitch, lnvar shadow mask, Black matrix, Short persistence phosphors. Input Signal Video Sync. Synchronization Horizontal : 31 -‘82 kHz : 50-120Hz Vertical Resolution Horizontal : Up to 1,280 dots : Up to 1,024 dots Vertical ENGS USH - : 0.7 Vp-p, Analog : Separate H, V or Composite H/V lTL level (optional Sync. on Green at 0.3 Vp-p) Video Clock Frequency 135 MHz (max.) Viewable Image Size 15.
