COLOUR MONITOR CM715ET USER MANUAL MANUEL D’UTILISATION BEDIENUNGSANEITUNG MANUAL DE USUARIO MANUALE DI ISTRUZIONI READ THE INSTRUCTIONS INSIDE CAREFULLY. KEEP THIS USER MANUAL FOR FUTURE REFERENCE. For future reference, record the serial number of your color monitor. SERIAL No. The serial number is located on the rear of the monitor. This monitor is ENERGY STAR® compliant when used with a computer equipped with VESA DPMS.
Table of Contents Introduction ..................................................................... 2 Features Package Overview Cautions........................................................................ 3 TCO'99 Statement ..........................................................6 For the Customers in the UK ...........................................8 Installation ......................................................................10 User Controls..................................................
INTRODUCTION Congratulations on your purchase of this high performance 19”moniter. Using state-of-the-art electronics, this monitor can support up to 1600 x 1200 resolution. The on-screen display(OSD) allows you to customize the display setting to suit your individual needs. Features ☺ 19-inch monitor with a large, 350 x 260 mm viewable screen for comfortable viewing. ☺ OSD controls for easy and accurate adjustment of the screen image. ☺ Energy Star compliant to reduce power consumption.
CAUTIONS NEVER REMOVE THE REAR COVER ! The rear cover MUST be removed only by authorized service personnel. This colour monitor contains high voltage components. THE RECEPTACLE SHOULD BE CLOSE TO THE MONITOR AND EASILY ACCESSIBLE ! INSTALL THE UNIT IN A SUITABLE ENVIRONMENT ! DO NOT expose this monitor to rain or moisture to prevent electric shock or fire hazard. This unit is designed to be used in an office or business environment. DO NOT subject the unit to vibrations, dust, or corrosive gases.
USE ONLY THE CORRECT VOLTAGE POWER OUTLET WITH SAFETY CONNECTION ! GROUND 200 - 240 V for Europe, etc. CAUTION for 200 - 240V operation only This equipment relies on the protective devices in the building installation for short-circuit and over-current protection. Refer to the following table for the suitable number and location of the protective devices which should be provided in the building installation.
BE CAREFUL OF STATIC ELECTRICITY ON CRT SURFACE ! To prevent electrical shock by the static electricity on the CRT surface, disconnect the power cord at least 30 SECONDS AFTER turning off the power. ABOUT CLEANING This monitor has a non-glare and anti-electrostatic treatment on the surface of the screen. Use water or alcoholic solvent with soft cloth like gauze to clean the surface of the screen.
TCO'99 Statement Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. This product meets the requirements for the TCO'99 scheme which provides for an international environmental and quality labelling of personal computers.
Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet) : development@tco.se Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.
CAUTIONS (Continued) For the Customers in the UK THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE UK PLEASE REFER TO THE NOTES ON THIS PAGE. IMPORTANT FOR UNITED KINGDOM WORDING FOR CLASS EQUIPMENT INSTRUCTION BOOKS AND LABELS The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug.
NOTE: The information in this manual is subject to change without notice. The manufacturer assumes no responsibility for any errors that may appear in this manual. TRADEMARK ACKNOWLEDGEMENT VGA is a registered trademark of International Business Machines Corporation. VESA is a trademark of a nonprofit organization, Video Electronics Standard Association. ENERGY STAR® is a U.S. registered mark of Environmental Protection Agency (EPA).
INSTALLATION 1. Connect the monitor signal cable 1 to the 15-pin mini D-sub (VGA) on the computer. 2. Connect the power cord to the power connector on the back panel of the monitor, then plug the other and into an appropriately grounded electrical outlet that is easily accessible and close to the monitor. 3. First turn on the computer, then the monitor. 4. Adjust the tilt and swivel base to make of your viewing comfortable. And now, your monitor installation is complete.
USER CONTROLS 1 Power button 2 Power LED Indicator LED Color Turn monitor on and off. 3 Select button Green Yellow 4 & State On Sleep Adjustments For adjusting the display parameters in the selected function. For selecting OSD functions.
OSD FUNCTION DESCRIPTION 1. Press any button 2. To select function, press the button. 3. To adjust function, press the button. / to display the OSD Menu. To exit the OSD menu, select the Exit icon, then press the 12 button once.
OSD ICON SUMMARY Icon Function Brightness Function Description Adjusts display brightness Contrast Adjusts display contrast H. Size Increases and decreases screen width H. Position V. Size Shifts display image right or left Increases and decrease screen height V. Position Shifts display image up or down Pin.
SPECIFICATION Screen Size 19" CRT Horizontal dot pitch 0.22 mm Horizontal mask pitch 0.21 mm Surface Non-glare Viewable Image Area (mm) 350 x 260 Input Signal Video signals. RGB Analog 0.7Vp-p / 75 Ohm a. Separate H/V, TTL (+/-) b. Composite H+V, TTL (+/-) Scanning Frequency Horizontal (KHz) 30 - 95 Vertical (Hz) 50 - 120 Max.
TROUBLESHOOTING Please make reference to following solutions for most of the failure symptoms occurred. If the symptom remains after trying the suggested solutions, please contact your local authorized service center. Problem: Power LED is not lit when monitor is powered on. Check to make sure that the power cord is properly connected. Make sure that extension cord or the surge protector is turned on if the monitor is plugged into such equipment. Problem: No display appears on screen.
Hitachi, Ltd. Tokyo, Japan International Sales Division THE HITACHI ATAGO BUILDING, No. 15 –12 Nishi Shinbashi, 2 – Chome, Minato – Ku, Tokyo 105-8430, Japan. Tel: 03 35022111 HITACHI EUROPE LTD, Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA UNITED KINGDOM Tel: 01628 643000 Fax: 01628 643400 Email: consumer -service@hitachi-eu.com HITACHI EUROPE S.A. 364 Kifissias Ave. & 1, Delfon Str. 152 33 Chalandri Athens GREECE Tel: 1-6837200 Fax: 1-6835964 Email: service.hellas@hitachi-eu.