COLOUR/COLOR LCD MONITOR CML190SXW CML190SXWB USER MANUAL MANUEL D’UTILISATION BEDIENUNGSANLEITUNG MANUAL DE USUARIO MANUALE DI ISTRUZIONI Ο∆ΗΓΙΕΣ ΧΕΙΡΙΣΜΟΥ READ THE INSTRUCTIONS INSIDE CAREFULLY. KEEP THIS USER MANUAL FOR FUTURE REFERENCE. For future reference, record the serial number of your colour monitor. SERIAL No. The serial number is located on the rear of the monitor. This monitor is ENERGY STAR® compliant when used with a computer equipped with VESA DPMS.
FOR HITACHI MODELS STARTING WITH “CM”: Hitachi America, Ltd. warrants our “CM” Hitachi CRT color monitor models to be free from defects in material and workmanship for 36 months from the date you purchased it if your purchase was made prior to 1/31/01 or 60 months if your purchase was made after 1/31/01 from your authorized Hitachi America,Ltd. monitor dealer.
for the benefit of the original owner only in accordance with all terms stated in this warranty. Warranty is not transferable. ENGLISH To obtain warranty service, call 1-800-562-2552 to obtain a return authorization number and the location of your Hitachi service center. If a problem occurs within the first 30 days after purchase AND IF CONSISTENT WITH YOUR DEALER’S RETURN POLICY, you can return the monitor to the dealer from whom you bought it.
CML190SXW CML190SXWB USER MANUAL Congratulations on your selection of the HITACHI Colour Monitor. Read the instructions inside carefully, and keep this user manual for future reference. NOTE: * The information in this manual is subject to change without notice. The manufacturer assumes no responsibility for any errors that may appear in this manual. * The reproduction, transmission or use of this documents or contents is not permitted without express written authority.
Chapter 2 Display Controls.................................................................. 16 User Controls ................................................................................................ 16 Adjusting the Monitor's Display ..................................................................... 16 ENGLISH Function Descriptions.................................................................................... 17 Chapter 3 Technical Information ..............................................
ENGLISH Using this Display Safely Common Safety Precautions Please read carefully and make sure you fully understand the following safety precautions: - Operations should be done according to instructions and procedures described in this manual. - Make sure to heed all warnings displayed on the device and manual. Neglecting to do so may result in fire or damage the device. Symbols Safety notifications are presented as shown below.
Warning Abnormal heat, smoke, sounds or smells. ENGLISH If anything abnormal should happen, turn OFF the power and unplug the power cord. Continued use in this condition may lead to electrical shock or fire. The area around the cord should be clear to allow the cord to be easily unplugged. Repair, Modification, Disassembly DO NOT attempt to repair, modify or disassemble the product. This may result in fire or electrical shock. Air vents - The air vents are to prevent the internal temperature from rising.
Handling of the power cord ENGLISH Use the power cord supplied with the product and be careful of the following during use. If handled improperly, the cord may be damaged resulting in electrical shock or fire. Never place objects on it. - DO NOT pull - DO NOT apply pressure - DO NOT fold - DO NOT wrap DO NOT use next to heating device Plugging and Unplugging - When plugging or unplugging the power cord in the socket, make sure to hold the plug.
Handling the AC adapter - DO NOT wet or handle with wet hands. This may result in electrical shock. - DO NOT use with devices other than this display. This may result in shock, fire, or ENGLISH damage to the device. - DO NOT use or place in areas where heat accumulates. This may result in fire. Multi-Tap Usage TO not attach multiple extension plugs into one outlet. This may result in fire and overloading lines will activate the circuit breakers causing data loss or damage to the product.
Contact with Metal and Other Edges When moving the computer be careful when coming in contact with the plastic and metal edges. It is possible to be injured. Use in Unstable Places DO NOT place on sloping or narrow areas that are unstable. The device may drop or fall and cause injury. Display Cable - Arrange the cables so that they are out of the way. If a cable is tripped on, it may cause injury and damage to the connected devices. - DO NOT place heavy objects on the cable.
Electronic Interference ENGLISH If used in the vicinity of other electronic devices, they may interfere with each other’s performances. Especially for devices such as radios and televisions, noise may enter their sound reception. If this should happen, try the following: - Place in a location as far away from radios and televisions as possible. - Change the facing of the antenna on the radio or television. - Use a different electrical socket.
FCC Statement Warning digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
For the Customers in the UK THIS PRODUCT IS SUPPLIED WITH A TWO-PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE UK PLEASE REFER TO THE NOTES ON THIS PAGE. ENGLISH IMPORTANT FOR UNITED KINGDOM WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA or BSI approved BS 1362 fuse must be used of the same rating.
Chapter 1 Installation Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that the LCD Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses very little power, some ventilation is needed to ensure that the Monitor does not become too hot. After you unpack the LCD Monitor, make sure that the following items were included in the box: * LCD Monitor * 1.
Cable Installation Please follow these instructions to install the cables. ENGLISH 1. Remove the back panel n from the rear of the monitor.(See Fig. 1.2,1-3) 2. Place the signal cable, the DC power cable into their correct respective grooves. Figure 1-2 Figure 1-3 Connecting the Display to your Computer 1. Power off your computer. 2. Connect one end of the signal cable to the LCD Monitor's VGA port or DVI port. (See Fig. 1-4) 3.
Connecting the AC Power 1. Connect the power cord to the AC adapter. (See Fig. 1-5) ENGLISH 2. Connect the AC adapter's DC output connector to the DC Power Jack of the monitor. 3. Connect the power cord to an AC power source. Figure 1-5 WARNING Please install a "Surge Protector" device between the AC Adapter and the electrical wall outlet for added protection against power surges to prevent the effects of sudden voltage variations from reaching the LCD Monitor.
Chapter 2 Display Controls ENGLISH User Controls A brief description and the location of all LCD Monitor function controls and indicators: Figure 2-1 1 Soft Power Switch 2 DC Power-On Indicator 3 Function Select Buttons 4 Adjustment Control Buttons Press the soft power switch to switch the monitor ON/OFF. LED displays Green color --- Power is ON. LED displays Dark color --- Power is OFF. LED displays Yellow color --- Monitor is in "Power Saving Mode".
Icon Function Brightness Contrast Function Description 101 scales of brightness are available to choose from (0 to 100). 101 scales of contrast are available to choose from (0 to 100). H. Position This function let's you adjust the display's horizontal position V. Position This function let's you adjust the display's vertical position. This function let's you select the images sharpness. Five selections are available.
Icon 9300 ENGLISH 7500 6500 User 18 Function CIE coordinate Color Temperature of 9300K CIE coordinated Color Temperature of 7500°K CIE coordinated Color Temperature of 6500K Description Sets the CIE coordinate color temperature to 9300K Sets the CIE coordinate color temperature to 7500°K Sets the CIE coordinate color temperature to 6500K Three colors (Red, Green, Blue) can be adjusted from the OSD menu Sets the settings to a by user defined CIE Temperature.
Chapter 3 Technical Information ENGLISH Specifications LCD Panel Size Display Type Resolution Display Dot Display Area (mm) Display Color Brightness Contrast Ratio Response Time Lamp Voltage Lamp Current Viewing Angle 19" (48 cm) Active matrix color TFT LCD 1280 x 1024 1280 x (RGB) x 1024 376.32 x 301.056 (H x V) 16.7M 2 250 cd/m (typical) 500:1 (typical) Ta=25°C Tr=15ms Tf=10ms 700 Vrms (typical) 7.0 mA rms.
Power Management Mode ENGLISH Power Consumption* AC Input LED Color ON 56W maximum 240 VAC Green OFF 4W maximum 240 VAC Yellow Soft switch off 4W maximum 240 VAC Dark Disconnected 4W maximum 240 VAC Yellow: Standby, Suspend, OFF Off: DC Power OFF Hard switch off 1W maximum 2W maximum 120 VAC 240 VAC Dark * Meeting VESA DPMS requirements measured from AC Input end of AC adapter.
Pin Assignment 6 1 11 5 15 PIN 1 2 3 4 Signal Description Red Green Blue Digital GND PIN 6 7 8 9 Signal Description Red Rtn Green Rtn Blue Rtn +5V PIN 11 12 13 14 Signal Description NC SDA H. Sync. V. Sync.
Standard Timing Table If the selected timing is NOT included in table below, this LCD monitor will use the most suitable available timing. ENGLISH Resolution H – Freq. (KHz) V. Freq. (Hz) Pixel Freq. (MHz) H/V Sync. Polarity Mode 640 x 350 31.469 70.087 25.175 +/- VGA-350 640 x 400 24.83 56.42 21.05 -/- NEC PC 9801 640 x 400 31.469 70.087 25.175 -/+, -/- 640 x 480 31.469 59.940 25.175 -/- VGA 480 640 x 480 35.000 66.670 30.240 -/- APPLE MAC – 480 640 x 480 37.861 72.
This LCD Monitor has pre-adjusted using factory to standard VGA timings. Due to the output timing differences among various VGA cards in the market, users may initially experience an unstable or unclear display whenever a new display mode or new VGA card is selected. ATTENTION This LCD Monitor Supports Multiple VGA Modes. Refer to the Standard Timing Table for a listing of modes supported by this LCD Monitor.
Hitachi, Ltd. Tokyo, Japan International Sales Division THE HITACHI ATAGO BUILDING, No. 15 –12 Nishi Shinbashi, 2 – Chome, Minato – Ku, Tokyo 105-8430, Japan. Tel: 03 35022111 HITACHI EUROPE LTD, Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA UNITED KINGDOM Tel: 01628 643000 Fax: 01628 643400 Email: consumer -service@hitachi-eu.com HITACHI EUROPE S.A. 364 Kifissias Ave. & 1, Delfon Str. 152 33 Chalandri Athens GREECE Tel: 1-6837200 Fax: 1-6835964 Email: service.hellas@hitachi-eu.