Color Plasma Display Monitor Model CMP5000WXU CMP5000WXJ USER'S MANUAL MANUEL UTILISATEUR READ THE INSTRUCTIONS INSIDE CAREFULLY. KEEP THIS USER MANUAL FOR FUTURE REFERENCE. For future reference, record the serial number of your monitor. SERIAL NO. The serial number is located on the rear of the monitor. Contents related to system specifications, power requirements, accessories, and other information differ with respect to the country where this unit is purchased. For customers living in the U.S.A.
English This unit has been designed for use as a computer display monitor. The optional video card is required if you wish to view other video signals on the monitor. For details consult your local retail dealer. Français Cet appareil est conçu pour une utilisation comme moniteur d’affichage d’ordinateur. La carte vidéo optionnelle est nécessaire si vous souhaitez regarder d’autres signaux sur ce moniteur. Pour plus de renseignements, consultez votre revendeur.
SAFETY GUIDELINES English This monitor is designed to be safe to use. However, fire or serious injury may occur unless you use this monitor in the proper way. Please follow the instructions shown below in order to avoid injury.
English SAFETY GUIDELINES(continued) WARNING Fire or electric shock may cause death or serious injury unless you follow the instruction. • The enclosed power cord must be used! Failure to do so may cause electric shock hazard or fire hazard. In USA/Canada, use a UL LISTED/CSA LABELLED or CERTIFIED power cord set meeting the following specifications : Rating: min. 125V, 6A , Length: max. 3.
English PRECAUTIONS • Installation environment Do not obstruct a ventilation hole. Do not put the monitor on carpet or blanket, or near a curtain which has a possibility of obstructing a ventilation hole of the monitor. Do not put the monitor in the following places. • Hot places such as near heater, place exposed to the direct rays of the sun. • A place where the temperature is widely changing. • Places with soot, dust or high humidity. • Poor air ventilation place. • Place near fire.
English SAFETY GUIDELINES(continued) • FCC (Federal Communications Commission) STATEMENT WARNING For model CMP5000WXU (Plasma Display) CMPAV05 (Video Card) WARNING : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
English USER’S MANUAL Thank you very much for purchasing the HITACHI Plasma Display Monitor. Before using your monitor, please carefully read the “SAFETY GUIDELINES” and this “USER’S MANUAL” so you will know how to operate the monitor properly. Keep this manual in a safe place. You will find it useful in the future. Notes on Installation Work: This product is marketed assuming that it is installed by qualified personnel with enough skill and competence.
English Features ¶ Introduces newly developed 50" XGA Wide Plasma Panel The new high-precision XGA 50" wide plasma panel pushes the envelope of previous high-luminance panels, producing brighter, clearer images with higher contrast. ¶ Newly developed full screen filter produces clear, high-contrast images even in a lighted room. The new full screen filter suppresses surface reflections to a minimum, producing clear, high-contrast images even in lighted locations.
English Contents SAFETY GUIDELINES .................................................. I Before Proceeding ...................................................... 2 How to Use This Manual .............................................................. 2 Checking Supplied Accessories ................................................... 3 Part Names and Functions ........................................ 4 Main Unit .......................................................................................
English Before Proceeding How to Use This Manual 1 Press MENU to display the menu screen. MAIN MENU INPUT1 PICTURE SCREEN : CO NT RA S T 0 : BR I GHT . 0 : +60 R. L E V E L : +60 G. L E V E L : +60 B. L E V E L : 0 H . E NH AN CE : V . E NH AN CE 0 This manual is set up to follow the course of actions and operations in the order that would seem most logical for someone setting up this unit.
English Before Proceeding Checking Supplied Accessories Check that the following accessories were supplied.
English Part Names and Functions Main Unit Operation panel on the main unit 3 Main unit 4 5 6 7 2 8 9 1 Note Part Names and Functions When optional speakers have been connected, the operation panel on the main unit will not be operable. Main unit 1 Remote control sensor Point the remote control toward the remote sensor to operate the unit (page 6). 2 STANDBY/ON indicator This indicator is red during standby mode, and turns to green when the unit is in the operation mode (page 16).
English Part Names and Functions Remote Control Unit 1 SCREEN SIZE button Press to select the screen size (page 18). 1 2 INPUT buttons 7 Use to select the input (page 16). 8 2 3 MENU button 9 Press to open and close the on-screen menu (pages 14 to 26). 4 ADJUST (5/∞/3/2) buttons 3 Use to navigate menu screens and to adjust various settings on the unit. Usage of cursor buttons within operations is clearly indicated at the bottom the on-screen menu display (pages 14 to 26).
English Part Names and Functions Operating range of the remote control unit Connection Panel When operating the remote control unit, point it at the remote sensor located on the front panel of the main unit. The remote control unit is operable up to 23 feet (7 m) from the unit and within a 30 angle on each side of the sensor. The connection panel is provided with two video input jacks and one video output jack. Audio input and speaker output jacks are also provided.
English Part Names and Functions AC INLET 8Ω ~16Ω SPEAKER + - 8Ω ~16Ω SPEAKER + – 1 CONTROL IN OUT 2 COMBINATION IN 3 INPUT1 RS-232C OUT 4 8 Synchronizing signal impedance selector switch Depending on the connections made at INPUT2, it may be necessary to set this switch to match the output impedance of the connected component’s synchronization signal. When the output impedance of the component’s synchronization signal is below 75 Ω, set this switch to the 75 Ω position (pages 9, 11).
English Installation and Connections Installation of the Unit Installation using the optional HITACHI stand or installation bracket Wall-mount installation of the unit This unit has been designed with bolt holes for wall-mount installation, etc.. The installation holes that can be used are shown in the diagram below. ÷ Please be sure to request installation or mounting of this unit or the installation bracket by an installation specialist or the dealer where purchased.
Connection to INPUT1 and INPUT2 The INPUT 1 and INPUT 2 jacks are used to connect the display to a computer. After making the connections, adjust the screen settings in accordance with the computer’s signal output. See pages 14-15 for information regarding settings. Output source INPUT2 jack Personal computer (PC) with RGB output [ON SYNC] G B R [H/V SYNC] HD VD English Installation and Connections Connection to a personal computer Connection method differs depending on the computer type.
English Installation and Connections When connecting to INPUT1 Connection of G ON SYNC analog RGB source Make G ON SYNC connections for a personal computer with output that has the synchronization signal layered on top of the green signal. INPUT1 ANALOG RGB OUTPUT (ANALOG RGB) When connecting to INPUT1 INPUT1 OUTPUT (ANALOG RGB) ANALOG RGB Connect the cable corresponding to the shape of the input terminal on this unit and the personal computer’s output terminal.
Connection of composite SYNC analog RGB source English Installation and Connections Audio Connections Make composite SYNC connections for a personal computer with output that has the vertical synchronization signal layered on top of the horizontal synchronization signal. Before making connections, be sure to check that the audio component’s power and the unit’s main power is off.
English Installation and Connections Power Cord Connection Connect the power cord after all component connections have been completed. 1 2 1 Connect the power cord to this unit. 2 Plug the power cord into a power outlet. CAUTION ÷ Use only the power cord provided. Installation and Connections ÷ Do not use a power supply voltage other than that indicated (AC 100 - 120 V, 50/60 Hz) as this may cause fire or electric shock.
English Installation and Connections How to Route Cables Speed clamps and bead bands are included with this unit for bunching cables together. Once components are connected, follow the following steps to route cables. * As viewed from the rear of the display. 1 2 Organize cables together using the provided speed clamps. Insert 1 into an appropriate hole on the rear of the unit, then snap 2 into the back of 1 to fix the clamp.
English Setting Up the System Setup after Connection 6 Press 5/∞ to select SETTING, then press SET. MAIN MENU PICTURE After components have been connected to INPUT1 or INPUT2, on-screen setup is necessary. Follow the procedure described below and make settings as they apply to the type of components connected.
4 CLAMP POSITION setup English Setting Up the System Press SET to select LOCKED. MAIN MENU PICTURE Depending on the signal, analog RGB signals may result in the screen image appearing with a whitish or greenish cast. In such cases, set “CLAMP POSITION” to LOCKED. ÷ Normally, leave this setting at AUTO.
English Operations 3 Selecting an Input Source This section explains the basic operation of this unit. Outlined on the following pages is how to turn the main power on and off, put this unit in the operation or standby mode and how to select connected components. Press INPUT on the remote control unit or the main unit to select the input. Input changes each time the main unit’s INPUT is pressed as follows.
To adjust the volume English Operations To confirm display settings DISPLAY VOLUME +/– Press VOLUME on the remote control unit. Use VOLUME + or VOLUME – to adjust the volume of the connected speakers. Press DISPLAY on the remote control unit. The currently selected input, screen size and refresh rates will be displayed for about 3 seconds. I NPUT 1 : 5 fH: fV: To mute the sound Operations V O L U ME 3 1. 5 kH z 60.
English Operations Screen Size Selection This unit incorporates screen modes of various height and width ratios. For optimal viewing, we recommend that you select the screen mode that best matches the video source that you are viewing. Although these modes are designed for full display of a picture on a wide screen, it is our hope that you make use of them with a full understanding of the manufacturer’s intentions.
3 Partial Image Enlargement (POINT ZOOM) This display allows any one of nine screen areas (AREA 1 to AREA 9) to be selected and enlarged to x1.5, x2, x3, or x4. When performing point zoom enlargement, the direction buttons (5/∞/2/3) can be used to move the enlarged portion up-down and right-left. 1 4 P.ZOOM SET Press SET to select the zoom ratio. Pressing SET repeatedly changes the zoom ratio in the following order: 3 x 1.5 3 x 2.0 x 4.0 2 x 3.
English Operations 3 Automatic Power OFF This display is equipped with automatic powermanagement and auto-power-off functions, which allow the unit to automatically switch to power-saving mode when no sync signal is detected. (A warning message appears onscreen before these functions operate.) Press 5/∞ to select either the POWER MANAGEMENT or AUTO POWER OFF mode.
Adjusting the Picture Quality Press MENU to display the menu screen. MAIN MENU INPUT1 PICTURE SCREEN : CO NT RA S T 0 : BR I GHT . 0 : + R. L E V E L 60 : + G. L E V E L 60 : +60 B. L E V E L : 0 H . E NH AN CE : V . E NH AN CE 0 SET UP OPTION RE S E T SELECT 2 SET ENTER MENU EXIT Press 5/∞ to select the adjustment item, then press SET. MAIN MENU INPUT1 PICTURE SCREEN : CO NT RAS T 0 : B R I GHT . 0 : +60 R. L E V E L : +60 G. L E V E L : +60 B. L E V E L : 0 H . E NH AN CE : V .
English Display Panel Adjustments Adjusting the Image Position and Clock (Automatic Adjustment) Pressing AUTO SET UP on either the main unit or the remote control unit will adjust the screen position and clock to optimum values. Note Perform this adjustment individually for each input function (INPUT 1, INPUT 2), and each signal type. Display Panel Adjustments AUTO SET UP AUTO SET UP Main Unit Operating Panel Remote Control Unit Press AUTO SET UP on either the main unit or remote control unit.
1 Press MENU to display the menu screen. MAIN MENU INPUT1 PICTURE SCREEN : CO NT RA S T 0 : BR I GHT . 0 : +60 R. L E V E L : +60 G. L E V E L : +60 B. L E V E L : 0 H . E NH AN CE : V . E NH AN CE 0 SET UP OPTION RE S E T SELECT 2 SET ENTER EXIT MENU Press 2/3 to select SCREEN. MAIN MENU PICTURE INPUT1 SCREEN : POS I T I ON CL OC K / P HA S E : SET UP 0 / 0 / OPTION 0 0 RE S E T SELECT 3 SET ENTER EXIT MENU Press 5/∞ to select the adjustment item, then press SET.
English Other Operations 5 Rewriting the Input Display (INPUT LABEL) MAIN MENU This function allows rewriting of the screen contents displayed with differing inputs. For example, the default “INPUT 1” can be changed to “COMPUTER” or other name describing the connected component (up to maximum of 8 characters). 2 INPUT1 I N P UT L ABE L BACK SPACE C I N P UT 1 B O 1 " A N 0 ' Example: To rewrite the default “INPUT 1” message to display “COMPUTER” instead.
English Other Operations Power Control Function AUTO FUNCTION The power control function allows screen brightness to be suppressed as a means of lowering power consumption and reducing display deterioration. This display is equipped with an optional AUTO FUNCTION selector. When enabled, the selector automatically switches the display’s input source to INPUT 1 when an image signal is detected at the INPUT 1 jack. 1 Press MENU to display the menu screen. The menu will be displayed.
English Other Operations 4 Press SET to select INPUT 1. The factory default setting is OFF. Each time SET is pressed the selector function switches alternately as shown: 2 Press 2/3 to select OPTION. MAIN MENU PICTURE INPUT1 SCREEN SET UP OPTION POWE R C O N T R O L : S T A ND A RD A U T O F U N C T I O N : OF F : F I X ED A UD I O O U T 3 OFF INPUT1 2 5 ÷ When OFF is selected, AUTO FUNCTION is disabled.
Cleaning Troubleshooting What may at first seem to be an malfunction, may be remedied with a quick check. Please check to see if a warning is displayed on the screen. If displayed, refer to the table below and check the mode. If there is no display check to see if the problem is listed on page 28. The problem may also be caused by something other than this unit so please also check the other components being used such as a video deck.
English Additional Information General problems Problem • No power • Unit cannot be operated. • Remote control does not operate. • INPUT is not changed. • Picture is cut off. • Strange color, light color, or dark, or color misalignment • Power is suddenly turned off. • No picture Possible Solution • Is the power cord disconnected? (page 12) • Has the MAIN POWER switch been switched on? (page 7) • External influences such as lightning, static electricity, etc., may cause improper operation.
Note In order to protect the panel and internal circuitry, this display is provided with a cooling fan designed to turn on/off and change speed automatically in accordance with ambient temperature conditions (the fan sound will change in accordance with its speed). Additional cautions • If the power is automatically turned off during operation of this unit, the following reasons may be the cause. 1 Is the POWER MANAGEMENT or AUTO POWER OFF function set to ON? (page 20).
English Additional Information Specifications General Light emission panel ............ 50 inch plasma display panel Number of pixels .............................................. 1280 x 768 Power supply ............................. AC 100 - 120 V, 50/60 Hz Rated current .................................................. 3.8 A - 3.1A Standby power consumption ...................................... 1 W External dimensions ........ 1218 (W) x 714 (H) x 98 (D) mm .............................
English Additional Information Supplement 1 PC signal compatibilty table (INPUT1, INPUT2) Refresh rate Resolution (Dot x Line) Vertical Horizontal 640x400 56.4Hz 24.8kHz Remarks 70.1Hz 60Hz 31.5kHz 31.5kHz 800 x600 66.7Hz 72Hz 75Hz 85Hz 56Hz 35.0kHz 37.9kHz 37.5kHz 43.3kHz 35.2kHz 832x624 60Hz 72Hz 75Hz 85Hz 74.6Hz 37.9kHz 48.1kHz 46.9kHz 53.7kHz 49.7kHz 852x480 60Hz 31.7kHz 1024x768 60Hz 48.4kHz 1152x864 70Hz 75Hz (74.9Hz) 85Hz 60Hz 56.5kHz 60.0kHz (60.2kHz) 68.7kHz 53.
English Additional Information Supplement 2 Explanation of Terms Signal assignment of INPUT 1 (Mini D-sub 15 pin socket connector) Aspect ratio 5 1 The TV screen’s width to height ratio is referred to as its aspect ratio. The aspect ratio on standard TVs is 4:3 and on wide TVs or High Definition TVs it is 16:9. G ON SYNC This indicates a video signal in the form of a synchronization signal added to the G (GREEN) signal of the R.G.B signal. 6 10 VGA 15 11 Additional Information Pin No.