Projector TEMP CP-SX1350 LAMP STANDBY/ON VIDEO BNG COMPONENT S-VIDEO LENS SHIFT MENU INTER RGB M1-D INPUT RESET SEARCH KEYSTONE FOCUS ZOOM User's Manual - Operating Guide Thank you for purchasing this projector. WARNING Before using the product, please read the "User's Manual Safety Guide" and related manuals to ensure the proper use of this product. After reading them, store them in a safe place for future reference. NOTE • The information in this manual is subject to change without notice.
Projector Features This multimedia projector is used to project various computer signals as well as NTSC/PAL/SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized. ●Ultra High Brightness Crisp, ultra-bright presentations is achieved by using a UHB (ultra high brightness) lamp and a highly efficient optical system. ●Whisper Mode Equipped Special mode is available for reducing projector noise to achieve quieter operation.
Content Projector Features …………………2 Preparation …………………………2 Part Names …………………………4 Projector ……………………………4 Control Buttons ……………………5 Remote control ……………………5 Setting Up ……………………………6 Arrangement ………………………6 Adjusting The Projector’s Elevator ……………………………7 Using The Lens shift Buttons ……7 Connecting Your Devices…………8 Connecting The Power Supply …11 Remote Control ……………………12 About The Laser Pointer ………12 Loading Batteries ………………12 Operating The Remote Control …………………13 Using The Remote ID Feature…………………………13 Usin
Part Names Projector TEMP LAMP STANDBY/ON VIDEO MENU BNG COMPONENT S-VIDEO INTER RGB LENS SHIFT FOCUS RESET M1-D INPUT ZOOM SEARCH KEYSTONE 6 3 5 1 2 4 1 2 3 4 5 Elevator button Elevator foot Remote sensor Lens cap Lens The picture is projected from here. 6 Filter cover An air filter is inside.
Part Names (continued) Control Buttons 7 8 6 y t r u w q 2 3 1 TEMP 4 9 0 = e 5 LAMP STANDBY/ON VIDEO BNG COMPONENT S-VIDEO LENS SHIFT MENU INTER RGB RESET M1-D INPUT FOCUS ZOOM SEARCH KEYSTONE Control Panel on the Projector 1 STANDBY/ON button and STANDBY/ON indicator 2 TEMP indicator 3 LAMP indicator 4 LENS SHIFT buttons 5 INPUT dial 6 SEARCH button 7 M1-D indicator 8 RGB indicator 9 BNC indicator 0 COMPONENT indicator - S-VIDEO indicator = VIDEO indicator q ZOOM buttons w FOCUS butto
Setting Up Arrangement WARNING • Before installation, make sure that the projector is turned off and the power code is disconnected. • Do not set up and move the projector, while it is hot. • Install the projector in a suitable environment according to instructions of the “User’s Manual – Safety Guide” and this manual. • The power outlet should be close to the projector and easily accessible. Refer to the illustrations and tables below to determine the screen size and projection distance.
Setting Up (continued) Adjusting The Projector's Elevator WARNING • Do not touch about the lens and ventilation openings during use or immediately after use to prevent a burn. CAUTION • Do not incline the projector rightward or leftward. Also do not incline it backward or forward exceeding 9 degrees. Exceeding these range could cause malfunction, and could shorten the lifetime of the consumables.
Setting Up (continued) Connecting Your Devices WARNING • Whenever attempting to connect other devices to the projector, read thoroughly the "User's Manual - Safety Guide", this manual and the manual of each device to be connected. Incorrect connecting could result in fire or electrical shock. CAUTION • TURN OFF ALL DEVICES prior to connecting them to the projector.
Setting Up (continued) Please refer to the following (for example) for connecting your devices. See the rear of the projector. You can see the ports.
Setting Up (continued) Examples of connection with a VCR/DVD Player VCR/DVD Player Projector CONTROL NETWORK REMOTE CONTROL AUDIO IN1 R-AUDIO IN-L VIDEO Audio out (R) Audio out (L) Video out R-AUDIO IN AUDIO IN-L VIDEO IN AUDIO OUT AUDIO IN2 H I R/CR/PR RGB OUT RGB G/Y B/CB/PB H CR/PR Ca/Pa Y HI V R-AUDIO IN-L VIDEO S-VIDEO BNC ■ If using a s-video signal J S-video out S-video cable S -VIDEO CONTROL AUDIO OUT AUDIO IN2 RGB OUT RGB CR/PR Ca/Pa R-AUDIO IN AUDIO IN-L Audio
Setting Up (continued) Connecting to a monitor CONTROL L AUDIO IN1 AUDIO IN2 Monitor R/CR/PR G/Y AUDIO OUT RGB OUT RGB Projector B/CB/PB H CR/PR Ca/Pa RGB in RGB cable Y V R-AUDIO IN-L L NETWORK REMOTE CONTROL VIDEO S-VIDEO BNC RGB OUT Connecting to a speaker (with amplifier) CONTROL Speaker Projector RGB G/Y RGB OUT B/CB/PB M Stereo Mini cable M AUDIO OUT AUDIO IN2 R/CR/PR Audio in NETWORK REMOTE CONTROL AUDIO IN1 H CR/PR Ca/Pa Y V R-AUDIO IN-L VIDEO S-VIDEO B
Remote Control About The Laser Pointer WARNING • The laser pointer of the remote control is used in place of a finger or rod. Never look directly into the laser beam outlet or point the laser beam at other people. The laser beam can cause vision problems. CAUTION • Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Remote Control (continued) Operating The Remote Control CAUTION • Do not disassemble the remote control. • Do not place the remote control near the projector’s lens, fan, or vents. • Do not drop or otherwise expose the remote control to physical impact. • Do not get the remote control wet or place it on wet objects on it. Doing so may result in malfunction. • Remove the batteries from the remote control and store them in a safe place if you won't be using the remote control for an extended period.
Remote Control (continued) Using The Mouse/Keyboard Control Function CAUTION • Before connecting, read the manuals of the device you will connect. Mistaken use of the mouse/keyboard control could damage your equipment. • Only connect to a PC or an USB Hub connected PC. • Do not unplug the connector cables while the computer is operating. Using the USB control feature, you can use the remote control as a simplified mouse or keyboard of the computer.
Power ON/OFF WARNING • When the power is ON, a strong light is emitted. Do not look into the lens or vents of the projector. NOTE • Turn the power on/off in right order. Please power on the projector before the connected devices. Power off the projector after the connected devices. Turning On The Power STANDBY/ON 1 Remove the lens cap. 2 Set the power switch to [ | ] (ON). The STANDBY/ON indicator will light to solid orange.
Operating Selecting An Input Signal 1 Select an input signal. ■ Using the INPUT dial Turn the INPUT dial of the projector. Turning the dial cycles through the input ports as shown below. Select the signal you wish to project. M1-D VIDEO RGB SEARCH button BNC S-VIDEO COMPONENT INPUT dial ■ Using SEARCH button Press the SEARCH button of the projector or the remote control. Pressing the button automatically cycles through input ports and displays the picture of retrieved signal.
Operating (continued) Selecting The Aspect Ratio LASER INDICATOR STANDBY/ON VIDEO 1 Press the Aspect button to toggle between the modes for aspect ratio. + LENS SHIFT FOCUS 4:3 – – ASPECT LASER PREVIOUS 16:9 + ZOOM – BLANK ■ For an RGB signal NORMAL RGB + ASPECT button NEXT MOUSE REAL ESC MENU POSITION RESET AUTO MAGNFY PinP VOLUME FREEZE MUTE memo NORMAL keeps the original aspect ratio of the input signal.
Operating (continued) Adjusting The Picture Position memo This function is not available for M1-D signals. 1 Press the POSITION button. As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the position. LASER INDICATOR STANDBY/ON VIDEO + LENS SHIFT FOCUS POSITION RGB + + ZOOM – – – BLANK ASPECT LASER PREVIOUS NEXT Cursor buttons MOUSE 2 Use the cursor buttons / / / to adjust the position.
Operating (continued) Adjusting The Volume 1 2 3 Press the VOLUME button. As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the volume. Use the cursor buttons adjust the volume. / VOLUME LASER INDICATOR STANDBY/ON VIDEO + RGB + + LENS SHIFT FOCUS to ZOOM – – – BLANK ASPECT LASER PREVIOUS NEXT Cursor buttons MOUSE 16 Press the VOLUME button again to close the dialog and complete this operation.
Operating (continued) Freezing The Screen 1 Press the FREEZE button. As illustrated on the right, a dialog will appear on the screen, and the screen will freeze at the current image. LASER INDICATOR STANDBY/ON VIDEO + FREEZE 2 + ZOOM – – – BLANK ASPECT LASER PREVIOUS Press the FREEZE button again to restore the screen to normal. The icon “||” will change to the icon “ ”. And after a couple of seconds, the dialog will be closed and the screen will be restored to normal.
Operating (continued) Displaying The Child Window memo This feature called "PinP (Picture in Picture)" is available only when a RGB signal is selected to main screen. And this feature does not work when UXGA (1600 x 1200) or higher signal is input. 1 2 Press the PinP button. The child window with a picture of a video signal will appear. Press the PinP button again to change the size of the child window or close the window.
Multifunctional Settings Using The Menu Functions This projector has the following menus: MAIN, PICTURE-1, PICTURE-2, INPUT, AUTO, SCREEN, OPTION and NETWORK. Each of these menus is operated using the same methods. The basic operations of these menus are as follows. 1 Press the MENU button. The menu will appear on the screen. ex. Turning off the built-in speaker LASER INDICATOR STANDBY/ON VIDEO + + LENS SHIFT FOCUS RGB – – BLANK ASPECT LASER PREVIOUS 1) Press the MENU button.
Multifunctional Settings (continued) MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK : SELECT MAIN Menu With the MAIN menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. Item BRIGHT CONTRAST ASPECT WHISPER BRIGHT CONTRAST ASPECT WHISPER MIRROR LANGUAGE [Language] RESET +0 +0 4:3 NORMAL NORMAL ENGLISH Description Adjust the brightness using the Adjust the contrast using the / / buttons. : buttons.
Multifunctional Settings (continued) MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK : SELECT PICTURE-1 Menu With the PICTURE-1 menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. Item GAMMA COLOR BAL R COLOR BAL G COLOR BAL B SHARPNESS COLOR TINT MY MEMORY NORMAL +0 +0 +0 +0 +0 +0 LOAD1 Description Select a gamma mode using the / buttons.
Multifunctional Settings (continued) PICTURE-1 Menu (continued) Item Description Select a command to load or save using the / buttons, and then press the (or the ENTER) button to perform the function.: LOAD1 LOAD2 LOAD3 LOAD4 SAVE1 SAVE2 SAVE3 SAVE4 MY MEMORY RESET This projector has 4 numbered memories for adjustment data. Performing the SAVE1, SAVE2, SAVE3 or SAVE4 puts the current adjustment data on the memory whose number corresponds with the command’s number.
Multifunctional Settings (continued) PICTURE-2 Menu With the PICTURE-2 menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK : SELECT V POSITION H POSITION H PHASE H SIZE OVER SCAN RESET 20 142 31 1344 5 memo This menu cannot be selected at a M1-D signal. Item V POSITION Adjust the vertical position using the / buttons.
Multifunctional Settings (continued) INPUT Menu With the INPUT menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK : SELECT COLOR SPACE COMPONENT VIDEO 3D-YCS VIDEO NR P. INP. INPUT P. INP. POSIT. POWERUP INPUT AUTO COMPONENT AUTO TURN OFF LOW VIDEO RGB Item Description COLOR SPACE Select a color space mode using the / buttons.
Multifunctional Settings (continued) INPUT Menu (continued) Item Description P.IN P. INPUT Select a signal input port for the child window using the / buttons. : VIDEO S-VIDEO memo About the child window, please refer to the section “Displaying the Child Window”. P.IN P. POSIT. Select the display position of the child window using the / buttons. : memo About the child window, please refer to the section “Displaying the Child Window”.
Multifunctional Settings (continued) AUTO Menu With the AUTO menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. Item MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK : SELECT ADJUST POWER OFF SEARCH RESET 0 min TURN ON Description Pressing the (or the ENTER) button performs the automatic adjustment.
Multifunctional Settings (continued) AUTO Menu (continued) Item Description Select the TURN ON or the TURN OFF using the / buttons. : TURN ON TURN OFF When the TURN ON is selected, detecting no signal cycles through input ports and displays the picture of retrieved signal. M1-D RGB VIDEO S-VIDEO SEARCH BNC COMPONENT memo When the TURN ON is selected, pressing the RGB button selects the M1-D ports, and pressing the VIDEO button selects the COMPONENT port.
Multifunctional Settings (continued) SCREEN Menu With the SCREEN menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK : SELECT BLANK START UP MyScreen MyScreen LOCK MENU POSITION MESSAGE RESET BLACK ORIGINAL TURN OFF TURN ON Item Description BLANK Select a type of the BLANK screen using the / buttons.
Multifunctional Settings (continued) SCREEN Menu (continued) Item Description MESSAGE Select the TURN ON or the TURN OFF using the / buttons. : TURN ON TURN OFF When the TURN ON is selected, the following message function works. The message of the “AUTO IN PROGRESS” for the auto adjustment. The message of the “NO INPUT IS DETECTED” The message of the “SYNC IS OUT OF RANGE” The message of the “Searching …” The message of the “Detecting …” The indication of the input signal by input change.
Multifunctional Settings (continued) OPTION Menu With the OPTION menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. Item MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK : SELECT VOLUME SPEAKER IR REMOTE IR REMOTE ID LAMP TIME FILTER TIME SERVICE RESET Description VOLUME Adjust the volume using the High Low SPEAKER Select the TURN ON or the TURN OFF using the / buttons.
Multifunctional Settings (continued) OPTION Menu (continued) Item Description Pressing the (or the ENTER) button calls the SERVICE menu. SERVICE Menu Select an item using the / buttons, and press the (or the ENTER) button to per form each function. : FANSPEED AUTO ADJUST LENS TYPE LENS LOCK GHOST FILTER MESSAGE SERVICE 34 NORMAL ENABLE AUTO TURN OFF 100 FANSPEED Select the fan speed level using the / buttons. : HIGH NORMAL The HIGH ups rotation speeds of fans, though.
Multifunctional Settings (continued) MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK : SELECT NETWORK Menu This projector provides the NETWORK function. If you use this function, please set up the projector according to the Network environment in which you use it. SETUP DHCP INFORMATION RESET TURN OFF memo If DHCP function on your Network is activated, the following operation is not normally required, because DHCP function on this projector is active as initial settings.
Network Setting Up This projector provides the NETWORK function. When you start to use this function, please consult your dealer for further information. To start, connect the NETWORK port to a gateway device via a CAT-5 cable, then set up the projector according to the Network environment in which you use it. When your Network enables the DHCP function You can set automatically, if you set the DHCP function to "TURN ON" using the NETWORK menu. Please refer to the section "NETWORK Menu".
Lamp WARNING HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.
Lamp (continued) Replacing The Lamp If the indicators or a message prompts you to replace the lamp, replace the lamp as soon as possible. 1 Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at least 45 minutes. 2 Contact your dealer to prepare a new lamp. Tell the dealer your lamp type number. If the projector is mounted on the ceiling, or if the lamp has broken, also ask the dealer to replace the lamp.
Air Filter WARNING • Please carefully read the “User’s Manual - Safety Guide. • Before caring, make sure the power switch is off and the power cable is not plugged in, then wait at least 45 minutes for the lamp to cool sufficiently. • Use only the air filter of the specified type NJ08081. • Do not use the projector with the air filter and filter cover removed. The use without the air filter could result in damage.
Other Care WARNING • Please carefully read the “User’s Manual - Safety Guide”. • Before caring, make sure the power switch is off and the power cable is not plugged in. • Be cautious of high temperature. Do not touch about the lens and ventilation openings during use or immediately after use prevent a burn. • Never try to care for the inside of the unit yourself. Doing so is dangerous. CAUTION • Incorrect care could have adverse influence such as discoloration, peeling paint, etc.
Troubleshooting Related Messages When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below. If the same message is displayed after the treatment, or if a message other than the following appears, please contact your dealer or service company. memo Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on.
Troubleshooting (continued) Related Messages (continued) Message REMINDER *** HRS PASSED AFTER THE LAST FILTER CHECK. FILTER MAINTENANCE IS ESSENTIAL TO REMOVE WARNING MESSAGE, RESET FILTER TIMER. SEE MANUAL FURTHER INFO. PLEASE CHECK THAT THE FILTER HAS BEEN CLEANED. FAILURE TO CLEAN MAY RESULT IN DAMAGE TO THE PROJECTOR. SEE MANUAL FURTHER INFO.
Troubleshooting (continued) Regarding The Indicator Lamps Lighting and flashing of the STANDBY/ON indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the table below. Please respond in accordance with the instructions within the table. If the same indication is displayed after the treatment, or if an indication other than the following is displayed, please contact your dealer or service company.
Troubleshooting (continued) Regarding The Indicator Lamps (continued) STANDBY/ON LAMP indicator indicator TEMP indicator Description Either there is no lamp and/or lamp cover, or either of these has not been properly fixed. Lighting in Red Blinking in Red Turned off Please turn the power off, and allow the unit to cool down at least 45 minutes.
Troubleshooting (continued) Phenomena That May Easily Be Mistaken For Machine Defects WARNING • Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet After making sure that the smoke or odor has stopped, contact your dealer or service company.
Troubleshooting (continued) Phenomena That May Easily Be Mistaken For Machine Defects (continued) Phenomenon Cases not involving a machine defect The signal cables are not correctly connected. Correctly connect the connection cables. Pictures are displayed, but no sounds are heard. The volume is adjusted to an extremely low level. Adjust the VOLUME to a higher level. 8, 9 19, 33 The sound is muted. Press the MUTE button to restore the sound.
Warranty And After-Service If a problem occurs with the equipment, first refer to the “Troubleshooting” and run through the suggested checks. If this does not resolve the problem, please contact your dealer or service company. They will tell you what warranty condition is applied. Specifications NOTE • This specifications are subject to change without notice. Item Product name Liquid crystal panel Specification Liquid crystal projector Panel size 2.5 cm (0.
Projector TEMP CP-SX1350 LAMP STANDBY/ON VIDEO BNG COMPONENT S-VIDEO LENS SHIFT MENU INTER RGB M1-D INPUT RESET FOCUS User's Manual - Operating Guide ZOOM SEARCH KEYSTONE TECHNICAL Dimensions 320 [unit: mm] 210 420 160 150 73 85.5 (at the bottom of lens position) to 92.
Example Of Computer Signal Resolution H×V fH (kHz) fV (Hz) Rating Signal mode Display mode 720 × 400 37.9 85.0 VESA TEXT Zoom in 640 × 480 31.5 59.9 VESA 630 × 480 35.0 66.7 640 × 480 37.9 72.8 640 × 480 37.5 75.0 640 × 480 43.3 800 × 600 800 × 600 VGA (60Hz) Zoom in Mac13"mode Zoom in VESA VGA (72Hz) Zoom in VESA VGA (75Hz) Zoom in 85.0 VESA VGA (85Hz) Zoom in 35.2 56.3 VESA SVGA (56Hz) Zoom in 37.9 60.3 VESA SVGA (60Hz) Zoom in 800 × 600 48.1 72.
Initial Set Signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the PICTURE-2 menu. Back porch b Front porch d Display interval c Back porch b Front porch d Display interval c DATA DATA H. Sync. V. Sync. Sync. a Computer / Signal Sync. a Horizontal signal timing (µs) TEXT a 2.0 b 3.0 c 20.3 d 1.
Connection To The Ports B D M AUDIO IN2 E CONTROL NETWORK REMOTE CONTROL AUDIO IN1 RGB R/CR/PR G/Y B/CB/PB A AUDIO OUT RGB OUT H CR/PR Ca/Pa R-AUDIO IN-L C BNC Y V VIDEO S-VIDEO H A RGB • Video signal: RGB separate, Analog, 0.7 Vp-p, 75 Ω terminator (positive) • H./V. sync. Signal: TTL level (positive/negative) • Composite sync.
Connection To The Ports (continued) O L N CONTROL NETWORK REMOTE CONTROL AUDIO IN1 AUDIO OUT AUDIO IN2 RGB R/CR/PR G/Y B/CB/PB RGB OUT H CR/PR Ca/Pa K Y V R-AUDIO IN-L BNC VIDEO I J S-VIDEO I VIDEO IN • RCA jack • System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL60 • 1.0 ± 0.1 Vp-p at 75 Ω terminator J S-VIDEO Pin Signal Color signal: 0.286 Vp-p (NTSC, burst), 75 Ω terminator Color signal: 0.300 Vp-p (PAL/SECAM, burst), 75 Ω terminator Brightness signal: 1.
Connection To The Ports (continued) F G CONTROL REMOTE CONTROL AUDIO IN1 AUDIO OUT AUDIO IN2 R/CR/PR NETWORK RGB G/Y RGB OUT B/CB/PB H CR/PR Ca/Pa Y V R-AUDIO IN-L VIDEO S-VIDEO BNC F CONTROL Computer side CONTROL port 1 2 3 4 5 6 7 8 9 D-Sub 9 pin plug - 5 4 3 2 1 9 8 7 6 D-Sub 9 pin jack RD TD GND RTS CTS - 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 CD RD TD DTR GND DSR RTS DTS RI RS-232C port 5 4 3 2 1 9 8 7 6 D-Sub 9 pin jack 1 2 3 4 5 6 7 8 9 D-Sub 9 pin plug memo About
RS-232C Communication Connecting The Cable 1 Turn off the projector and the computer power supplies. 2 Connect the CONTROL port of the projector with a RS-232C port of the computer by a RS-232C cable. Use the cable that fulfills the specification shown in the previous page. 3 Turn on the computer power supply and after the computer has started up, turn on the projector power supply. Communications Setting 19200bps, 8N1 1. Protocol Consist of header (7 bytes) + command data (6 bytes). 2.
RS-232C Communication (continued) Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)+‘00H’+‘00H’) from the computer to the projector. (2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer. Changing the projector settings (Set command) (1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) + setting code (2 bytes)) from the computer to the projector.
RS-232C Communication (continued) Command Data Chart Names Operation type Command data Header Type Setting code Get BE EF 03 06 00 B9 D3 02 00 07 20 00 00 Keystone V Increment Decrement BE EF BE EF 03 03 06 00 06 00 DF D3 0E D2 04 00 05 00 07 20 07 20 00 00 00 00 Keystone V Reset Execute BE EF 03 06 00 08 D0 06 00 0C 70 00 00 Get BE EF 03 06 00 E9 D0 02 00 0B 20 00 00 Increment BE EF 03 06 00 8F D0 04 00 0B 20 00 00 Decrement BE EF 03 06 00 5E D1 05 00 0
RS-232C Communication (continued) Command Data Chart (continued) Names Language Operation type Set Type Setting code ENGLISH BE EF 03 06 00 F7 D3 01 00 05 30 00 00 FRANÇAIS BE EF 03 06 00 67 D2 01 00 05 30 01 00 DEUTSCH BE EF 03 06 00 97 D2 01 00 05 30 02 00 ESPAÑOL BE EF 03 06 00 07 D3 01 00 05 30 03 00 ITALIANO BE EF 03 06 00 37 D1 01 00 05 30 04 00 NORSK BE EF 03 06 00 A7 D0 01 00 05 30 05 00 NEDERLANDS PORTUGUÊS 日本語 BE EF 03 06 00 57 D0 01 00 0
RS-232C Communication (continued) Command Data Chart (continued) Names Operation type Command data Header Type Setting code 50 BE EF 03 06 00 EF F6 01 00 B3 30 05 00 60 BE EF 03 06 00 7F F7 01 00 B3 30 04 00 70 BE EF 03 06 00 4F F5 01 00 B3 30 03 00 80 BE EF 03 06 00 DF F4 01 00 B3 30 02 00 90 BE EF 03 06 00 2F F4 01 00 B3 30 01 00 100 BE EF 03 06 00 BF F5 01 00 B3 30 00 00 Get BE EF 03 06 00 8C F5 02 00 B3 30 00 00 Get BE EF 03 06 00 01 D2
RS-232C Communication (continued) Command Data Chart (continued) Names Operation type Get V Position Increment Decrement V Position Reset Execute Get H Position Increment Decrement H Position Reset Execute Get H Phase Increment Decrement Get H Size Increment Decrement H Size Reset Execute Get Over Scan Increment Decrement Over Scan Reset Execute AUTO RGB Set SMPTE240 Color Space REC709 REC601 Get COMPONENT Set Component SCART RGB Get AUTO NTSC PAL SECAM Set Video Format NTSC 4.
RS-232C Communication (continued) Command Data Chart (continued) Names Video NR Auto Adjust Auto off Auto Search Blank Color Blank on/off Startup Operation type Command data Header Type Setting code LOW Set MIDDLE HIGH Get Execute Get Increment Decrement TURN OFF Set TURN ON Get My Screen Original BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF 03 03 03 03 03 03 03 03 03 03 03 03 03 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 26
RS-232C Communication (continued) Command Data Chart (continued) Names Operation type Get Volume Increment Decrement TURN OFF Set Mute TURN ON Get Lamp Time Get Lamp Time Reset Execute Filter Time Get Filter Time Reset Execute Get Magnify Increment Decrement Normal Set Freeze Freeze Get TURN OFF Set TURN ON Command data Header BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 06 00
RS-232C Communication (continued) Command Data Chart (continued) Names Operation type Type Setting code BE EF 03 06 00 FE 22 01 00 00 23 00 00 Large Small Get BE EF BE EF BE EF 03 03 03 06 00 06 00 06 00 6E 23 9E 23 CD 22 01 00 01 00 02 00 00 23 00 23 00 23 01 00 02 00 00 00 Upper Left BE EF 03 06 00 02 23 01 00 01 23 00 00 Upper Right BE EF 03 06 00 92 22 01 00 01 23 01 00 Bottom Left BE EF 03 06 00 62 22 01 00 01 23 02 00 Bottom Right BE EF 03 06 00 F2 23 01
RS-232C Communication (continued) Command Data Chart (continued) Names Operation type Type Setting code BE EF 03 06 00 9E D9 01 00 18 20 10 00 BE BE BE BE EF EF EF EF 03 03 03 03 06 06 06 06 AE 5E 9E 0E 01 01 01 01 18 18 18 18 03 00 04 05 S-Video BE EF 03 06 00 3E D5 01 00 18 20 02 00 Video BE EF 03 06 00 CE D5 01 00 18 20 01 00 Get BE EF 03 06 00 6D D4 02 00 18 20 00 00 DISABLE BE EF 03 06 00 A2 D5 01 00 19 20 00 00 ENABLE BE EF 03 06 00 32 D4 01 00
Hitachi, Ltd. Tokyo, Japan International Sales Division THE HITACHI ATAGO BUILDING, No. 15 –12 Nishi Shinbashi, 2 – Chome, Minato – Ku, Tokyo 105-8430, Japan. Tel: 03 35022111 HITACHI EUROPE LTD, Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA UNITED KINGDOM Tel: 01628 643000 Fax: 01628 643400 Email: consumer -service@hitachi-eu.com HITACHI EUROPE S.A. 364 Kifissias Ave. & 1, Delfon Str. 152 33 Chalandri Athens GREECE Tel: 1-6837200 Fax: 1-6835964 Email: service.hellas@hitachi-eu.