Projector CPX10WN/CPX11WN/ CPWX12WN User's Manual (detailed) Operating Guide Thank you for purchasing this projector. WARNING ►Before using this product, please read all manuals for this product. Be sure to read Safety Guide rst. After reading them, store them in a safe place for future reference. About this manual Various symbols are used in this manual. The meanings of these symbols are described below.
Read this Safety Guide first. Projector User's Manual - Safety Guide Thank you for purchasing this projector. WARNING • Before using, read these user's manuals of this projector to ensure correct usage through understanding. After reading, store them in a safe place for future reference. Incorrect handling of this product could possibly result in personal injury or physical damage.
Safety Precautions WARNING Never use the projector if a problem should occur. Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. can cause a fire or electrical shock. In such case, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer.
Safety Precautions (continued) WARNING Be cautious of High temperatures of the projector. High temperatures are generated when the lamp is lit. It could result in fire or burn. Use special caution in households where children are present. Do not touch about the lens, air fans and ventilation openings during use or immediately after use, to prevent a burn. Take care of ventilation. • Keep a space of 30 cm or more between the sides and other objects such as walls.
Safety Precautions (continued) WARNING Be careful in handling the light source lamp. The projector uses a high-pressure mercury glass lamp made of glass. The lamp can break with a loud bang, or burn out. When the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes. Please carefully read the section “Lamp”. Be careful in handling the power cord and external connection cables.
Safety Precautions (continued) CAUTION Be careful in moving the projector. Neglect could result in an injury or damage. • Do not move the projector during use. Before moving, disconnect the power cord and all external connections, and close the slide lens door or attach the lens cap. • Avoid any impact or shock to the projector. • Do not drag the projector. • For moving the projector, use the enclosed case or bag if provided. Do not put anything on top of the projector.
Safety Precautions (continued) CAUTION Remove the power cord for complete separation. • For safety purposes, disconnect the power cord if the projector is not to be used for prolonged periods of time. • Before cleaning, turn off and unplug the projector. Neglect could result in fire or electrical shock. Disconnect the plug from the power outlet. Ask your dealer to cleaning inside of the projector about every year. Accumulations of dust inside the projector cause result in fire or malfunction.
Safety Precautions (continued) NOTE About consumables. Lamp, LCD panels, polarizors and other optical components, and air filter and cooling fans have a different lifetime in each. These parts may need to be replaced after a long usage time. • This product isn’t designed for continuous use of long time.
Lamp WARNING HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.
Regulatory Notices FCC Statement Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Contents Introduction . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . 3 Checking the contents of package . . . 3 Part names . . . . . . . . . . . . . . . . . . . . 4 Setting up . . . . . . . . . . . . . . . . . 7 Arrangement . . . . . . . . . . . . . . . . . . . 7 Connecting with your devices . . . . . 10 Connecting to a power supply. . . . . 15 Fastening the adapter cover . . . . . . 16 Using the security bar and slot . . . . 16 Remote control . . . . . . . . . . . .
Introduction Introduction Features The projector provides you with the broad use by the following features. 9 This projector has a variety of I/O ports that supposedly cover for any business scene. The HDMI port can support various image equipment which have digital interface to get clearer pictures on a screen. 9 If you insert a USB storage device, such as a USB memory, into the USB TYPE A port and select the port as the input source, you can view images stored in the device.
Introduction Part names (1) Lamp cover ( HOT! (1) 93) (2) (3) (4) (11) The lamp unit is inside. (2) FOCUS ring ( 24) (3) ZOOM ring ( 24) (4) Control panel ( 5) (5) Elevator buttons (x 2) ( 24) (6) Elevator feet (x 2) ( 24) (7) Remote sensor ( 17) (8) Lens ( 97) (9) Intake vents (10) Filter cover ( 95) (9) (15) (10) (5) (6) (8) HOT! (12) (7) (5) The air lter and intake vent are inside.
Introduction Part names (continued) Control panel (1) STANDBY/ON button ( 19) (2) INPUT button ( 22, 29) (3) MENU button ( 29) It consists of four cursor buttons. (4) ECO button ( 56, 57) (5) POWER indicator ( 19, 100) (6) TEMP indicator ( 100) (7) LAMP indicator ( 100) (1) (2) (3) (5) (6) (7) 11 ~ 14) Rear panel ( (1) LAN port (2) USB TYPE A port (3) HDMI port (4) USB TYPE B port (5) VIDEO port (6) S-VIDEO port (7) AUDIO IN1 port (1) (2) (4) (3) HDMI USB TYPE A DC5V 0.
Introduction Part names (continued) Remote control (1) VIDEO button ( 22) (2) COMPUTER button ( 22) (3) SEARCH button ( 23) (4) STANDBY/ON button ( 19) (5) ASPECT button ( 23) (6) AUTO button ( 25) (7) BLANK button ( 28) (8) MAGNIFY - ON button ( 27) (9) MAGNIFY - OFF button ( 27) (10) MY SOURCE/DOC.
Setting up Setting up Install the projector according to the environment and manner the projector will be used in. For the case of installation in a special state such as ceiling mount, the specied mounting accessories ( 6SHFL¿FDWLRQV in the User’s Manual (concise)) and service may be required. Before installing the projector, consult your dealer about your installation.
Setting up Arrangement (continued) WARNING ►Install the projector where you can access the power outlet easily. If an abnormality should occur, unplug the projector urgently. Otherwise it could cause a re or electric shock. ►Do not subject the projector to unstable conditions. If the projector falls or topples over, it could result in injury or damage to the projector and the surrounding things. Using a damaged projector could result in a re and an electric shock.
Setting up Arrangement (continued) CAUTION ►3ODFH WKH SURMHFWRU LQ D FRRO SODFH ZLWK VXI¿FLHQW ventilation. The projector may shutdown automatically or may malfunction if its internal temperature is too high. Using a damaged projector could result in a re and an electric shock. • Do not place the projector in direct sunlight or near hot objects such as heaters. • Do not place the projector where the air from an air conditioner or similar unit will blow on it directly.
Setting up Connecting with your devices Before connecting the projector to a device, consult the manual of the device to conrm that the device is suitable for connecting with this projector and prepare the required accessories, such as a cable in accord with the signal of the device. Consult your dealer when the required accessory did not come with the product or the accessory is damaged.
Setting up Connecting with your devices (continued) Computer HDMI USB TYPE A DC5V 0.5A USB TYPE B COMPUTER IN1 S-VIDEO VIDEO LAN AC IN AUDIO OUT MONITOR OUT COMPUTER IN2 AUDIO IN1 AUDIO IN2 CONTROL NOTE • Before connecting the projector to a computer, consult the computer’s manual and check the compatibility of the signal level, the synchronization methods and the display resolution output to the projector. - Some signal may need an adapter to input this projector.
Setting up Connecting with your devices (continued) Computer External device Access point USB wireless adapter (optional) USB storage device HDMI USB TYPE A DC5V 0.5A USB TYPE B COMPUTER IN1 S-VIDEO VIDEO LAN AC IN AUDIO OUT MONITOR OUT COMPUTER IN2 AUDIO IN1 AUDIO IN2 CONTROL CAUTION ► Before connecting the projector to a network system be sure to obtain the consent of the administrator of the network. ►Do not connect the LAN port to any network that might have the excessive voltage.
Setting up Connecting with your devices (continued) HDMI USB TYPE A DC5V 0.
Setting up Connecting with your devices (continued) Speakers Monitor (with an amplier) RGB IN HDMI USB TYPE A DC5V 0.
Setting up Connecting to a power supply the connector of the power cord into the 1. Put AC IN (AC inlet) of the projector. plug the power cord’s plug into the 2. Firmly outlet. In a couple of seconds after the power supply connection, the POWER indicator will light up in steady orange. Please remember that when the DIRECT POWER ON function activated ( 53), the connection of the power supply make the projector turn on.
Setting up Fastening the adapter cover Use the supplied adapter cover to prevent the USB wireless adapter from coming off easily. 1. Loosen the screw (marked with triangle) on the bottom right of the USB TYPE A port. 1 the tab of the cover into the 2. Insert hole at the upper left of the USB 3 TYPE A port in the direction of the arrow. Align the screw holes on the projector and the cover. Then insert the screw removed from the projector into the hole and tighten the screw. 2 3.
Remote control Remote control Installing the batteries Please insert the batteries into the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a safe place. Holding the hook part of the battery 1 2 3 cover, remove it. Align and insert the two AA batteries (HITACHI MAXELL or HITACHI MAXELL ENERGY, Part No.
Remote control Using as a simple PC mouse & keyboard The accessory remote control works as a simple mouse and keyboard of the computer, when the projector’s USB TYPE B port and the computer’s type A USB port are connected and MOUSE is selected for the USB TYPE B item in the OPTION menu ( 54). USB TYPE B (1) PAGE UP key: Press PAGE UP button. USB TYPE B port (2) PAGE DOWN key: Press PAGE DOWN button. (3) Mouse left button: Press ENTER button. (4) Move pointer: Use the cursor buttons ▲, ▼, ◄ and ►.
Power on/off Power on/off Turning on the power STANDBY/ON button POWER indicator Make sure that the power cord is rmly and 1. correctly connected to the projector and the 2. outlet. Make sure that the POWER indicator is steady orange ( 100). Then remove the lens cover. Press STANDBY/ON button on the projector or the remote control. The projection lamp will light up and POWER indicator will begin blinking in green.
Power on/off Turning off the power the STANDBY/ON button on the projector or the remote control. 1. Press The message “Power off?” will appear on the screen for about 5 seconds. the STANDBY/ON button again while the message appears. 2. Press The projector lamp will go off, and the POWER indicator will begin blinking in 3. orange. Then POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete ( 100).
Operating Operating Adjusting the volume VOLUME +/- button the VOLUME +/VOLUME - buttons to adjust the volume. 1. Use A dialog will appear on the screen to aid you in adjusting the volume. If you do not do anything, the dialog will automatically disappear after a few seconds. VIDEO ASPECT MAGNIFY ON COMPUTER MY SOURCE/ DOC.CAMERA AUTO FREEZE SEARCH PAGE UP BLANK VOLUME 㧗 DOWN OFF MY BUTTON ● When is selected for current picture input port, the volume adjustment is disabled.
Operating Selecting an input signal INPUT button INPUT button on the projector. 1. Press Each time you press the button, the projector switches its input port from the current port as below. COMPUTER IN1 Æ COMPUTER IN2 Æ LAN VIDEO USB TYPE A S-VIDEO USB TYPE B HDMI ● While ON is selected for AUTO SEARCH item in OPTION menu ( 53), the projector will keep checking the ports in above order repeatedly till an input signal is detected.
Operating Searching an input signal SEARCH button on the remote control. 1. Press The projector will start to check its input ports as below in SEARCH button order to nd any input signals. When an input is found, the projector will stop searching and display the image. If no signal is found, the projector will return to the state selected before the operation. VIDEO ASPECT MAGNIFY ON COMPUTER MY SOURCE/ DOC.
Operating Adjusting the projector's elevator When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally. Using the feet can also tilt the projector in order to project at a suitable angle to the screen, elevating the front side of the 12° projector within 12 degrees. This projector has 2 elevator feet and 2 elevator knobs. An elevator foot is adjustable while pulling up the elevator knob on the same side as it. 1.
Operating Using the automatic adjustment feature AUTO button on the remote control. 1. Press Pressing this button performs the following. AUTO button VIDEO COMPUTER MY SOURCE/ DOC.CAMERA For a computer signal The vertical position, the horizontal position and the horizontal phase will be automatically adjusted. Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.
Operating Correcting the keystone distortions KEYSTONE button on the remote 1. Press control. A dialog will appear on the screen to aid you in correcting the distortion. 2. Use the ▲/▼ cursor buttons to select AUTO or MANUAL operation, and press the ► button to perform the following. (1) AUTO executes automatic vertical keystone correction. (2) MANUAL displays a dialog for keystone correction. Use the ◄/► buttons for adjustment.
Operating Using the magnify feature the MAGNIFY ON button on the remote control. 1. Press The picture will be magnied, and the MAGNIFY dialog will appear on the screen. When the MAGNIFY ON button is pressed for the rst time after the projector is turned on, the picture will be zoomed by 1.5 times. On the dialog, triangle marks to show each direction will be displayed. MAGNIFY ON/OFF button VIDEO ASPECT MAGNIFY ON COMPUTER MY SOURCE/ DOC.
Operating Temporarily freezing the screen 1. Press the FREEZE button on the remote control. The “FREEZE” indication will appear on the screen (however, the indication will not appear when the OFF is selected for the MESSAGE item in the SCREEN menu ( 49)), and the projector will go into the FREEZE mode, which the picture is frozen. To exit the FREEZE mode and restore the screen to normal, press the FREEZE button again. FREEZE button VIDEO ASPECT MAGNIFY ON COMPUTER MY SOURCE/ DOC.
Operating Using the menu function This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK, SECURITY and EASY MENU. EASY MENU consists of functions often used, and the other menus are classied into each purpose and brought together as the ADVANCED MENU. Each of these menus is operated using the same methods. While the projector is displaying any menu, the MENU button on the projector works as the cursor buttons.
Operating Using the menu function (continued) close the MENU, press the MENU button again or select EXIT and press 3. To the ◄ cursor button or ENTER button. Even if you do not do anything, the dialog will automatically disappear after about 30 seconds. ● If you want to move the menu position, use the cursor buttons after pressing the POSITION button. ● Some functions cannot be performed when a certain input port is selected, or when a certain input signal is displayed.
EASY MENU EASY MENU From the EASY MENU, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons. Then perform it according to the following table. Item ASPECT AUTO KEYSTONE KEYSTONE Description Using the ◄/► buttons switches the mode for aspect ratio. See the ASPECT item in IMAGE menu ( 36). Using the ► button executes the auto keystone function. See the AUTO KEYSTONE item in SETUP menu ( 43). Using the ◄/► buttons corrects the vertical keystone distortion.
EASY MENU Item ECO MODE INSTALLATION Description Using the ◄/► buttons swithes the ECO MODE. See the ECO MODE item in SETUP menu ( 44). Pressing the ► button displays the INSTALLATION dialog. See the INSTALLATION item in SETUP menu ( 44). RESET Performing this item resets all of the EASY MENU items except the FILTER TIME and LANGUAGE. A dialog is displayed for conrmation. Selecting the OK using the ► button performs resetting. FILTER TIME The usage time of the air lter is shown in the menu.
PICTURE menu PICTURE menu From the PICTURE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. Item BRIGHTNESS CONTRAST Description Using the ◄/► buttons adjusts the brightness. Dark Ù Light Using the ◄/► buttons adjusts the contrast. Weak Ù Strong Using the ▲/▼ buttons switches the gamma mode.
PICTURE menu Item Description Using the ▲/▼ buttons switches the color temperature mode. 3 LOW 6 Hi-BRIGHT-3 3 CUSTOM Ù Ù Ù 6 CUSTOM Ù Ù 2 CUSTOM Ù 1 HIGH Ù 1 CUSTOM Ù 2 MID Ù 5 CUSTOM Ù 5 Hi-BRIGHT-2 Ù 4 CUSTOM Ù 4 Hi-BRIGHT-1 To adjust CUSTOM COLOR TEMP Selecting a mode whose name includes CUSTOM and then pressing the ► button or the ENTER button displays a dialog to aid you in adjusting the OFFSET and GAIN of the selected mode.
PICTURE menu Item Description SHARPNESS Using the ◄/► buttons adjusts the sharpness. Weak Ù Strong • There may be some noise and/or the screen may icker for a moment when an adjustment is made. This is not a malfunction. MY MEMORY This projector has 4 memories for adjustment data (for all the items of the PICTURE menu). Selecting a function using the ▲/▼ buttons and pressing the ► or ENTER button performs each function.
IMAGE menu IMAGE menu From the IMAGE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. Item Description Using the ▲/▼ buttons switches the mode for aspect ratio.
IMAGE menu Item Description V POSITION Using the ◄/► buttons adjusts the vertical position. Down Ù Up • Over-adjusting the vertical position may cause noise to appear on the screen. If this occurs, please reset the vertical position to the default setting. Pressing the RESET button when the V POSITION is selected will reset the V POSITION to the default setting. • When this function is performed on a video signal or an s-video signal, the range of this adjustment depends on OVER SCAN ( 36) setting.
IMAGE menu Item Description H PHASE Using the ◄/► buttons adjusts the horizontal phase to eliminate icker. Right Ù Left • This item can be selected only for a computer signal or a component video signal. This function is unavailable for a signal from the LAN, USB TYPE A, USB TYPE B or HDMI port. H SIZE Using the ◄/► buttons adjusts the horizontal size. Small Ù Large • This item can be selected only for a computer signal.
INPUT menu INPUT menu From the INPUT menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. Item Description Using the ▲/▼ buttons switches the progress mode.
INPUT menu Item Description VIDEO FORMAT The video format for S-VIDEO port and VIDEO port can be set. (1) Use the ▲/▼ buttons to select the input port. (2) Using the ◄/► buttons switches the mode for video format. AUTO Ù NTSC Ù PAL Ù SECAM N-PAL Ù M-PAL Ù NTSC4.43 • This item is performed only for a video signal from the VIDEO port or the S-VIDEO port. • The AUTO mode automatically selects the optimum mode. • The AUTO operation may not work well for some signals. If the picture becomes unstable (e.g.
INPUT menu Item Description COMPUTER IN The computer input signal type for COMPUTER IN1 and IN2 ports can be set. (1) Use the ▲/▼ buttons to select the COMPUTER IN port to be set. (2) Use the ◄/► buttons to select the computer input signal type. AUTO Ù SYNC ON G OFF • Selecting the AUTO mode allows you to input a sync on G signal or component video signal from the port ( 11, 13). • In the AUTO mode, the picture may be distorted with certain input signals.
INPUT menu 42 Item Description RESOLUTION The resolution for the COMPUTER IN1 and COMPUTER IN2 input signals can be set on this projector. (1) In the INPUT menu select the RESOLUTION using the ▲/▼ buttons and press the ► button. The RESOLUTION menu will be displayed. (2) In the RESOLUTION menu select the resolution you wish to display using the ▲/▼ buttons. Selecting AUTO will set a resolution appropriate to the input signal.
SETUP menu SETUP menu From the SETUP menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. Item Description Selecting this item performs the Automatic keystone distortion correction. Projector automatically corrects vertical keystone distortion due to the (forward/backward) setup angle by itself.
SETUP menu Item Description Using the ▲/▼ buttons turns on/off the AUTO ECO MODE. ON Ù OFF AUTO ECO MODE • When ON is selected, the projector will always be set to Eco mode at start-up regardless of the ECO MODE ( below) setting. An OSD message “AUTO ECO MODE” will be displayed for a while when the projector starts with this function activated. Using the ◄/► buttons swithes the ECO MODE.
SETUP menu Item Description STANDBY MODE Using ▲/▼ buttons switches the standby mode setting between NORMAL and SAVING. NORMAL Ù SAVING When SAVING is selected, the power consumption in the standby mode is lowered with some functional restriction as below: • When SAVING is selected, the RS-232C communication control except to turn the projector on and the network function are disabled while the projector is in the standby mode.
AUDIO menu AUDIO menu From the AUDIO menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or the ENTER button to execute the item. Then perform it according to the following table. Item Description VOLUME Using the ◄/► buttons adjusts the volume. Low Ù High SPEAKER Using the ▲/▼ buttons turns on/off the built-in speaker. ON Ù OFF When OFF is selected, the built-in speaker does not work.
SCREEN menu SCREEN menu From the SCREEN menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. Item LANGUAGE Description Using the ▲/▼/◄/► buttons switches the OSD (On Screen Display) language. ENGLISH Ù FRANÇAIS Ù DEUTSCH Ù ESPAÑOL (shown in the LANGUAGE dialog) Press the ENTER or INPUT button to save the language setting.
SCREEN menu Item Description MyScreen This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen. Display the image you want to capture before executing the following procedure. 1. Selecting this item displays a dialog titled “MyScreen”. It will ask you if you start capturing an image from the current screen. Please wait for the target image to be displayed, and press the ENTER or INPUT button when the image is displayed.
SCREEN menu Item Description MyScreen Lock Using the ▲/▼ buttons turns on/off the MyScreen lock function. ON Ù OFF When the ON is selected, the item MyScreen is locked. Use this function for protecting the current MyScreen. • This function cannot be selected when the ON is selected to the MyScreen PASSWORD item in SECURITY menu ( 75). MESSAGE Using the ▲/▼ buttons turns on/off the message function. ON Ù OFF When the ON is selected, the following message function works.
SCREEN menu Item SOURCE NAME Description Each input port for this projector can have a name applied to it. (1) Use the ▲/▼ buttons on the SCREEN menu to select SOURCE NAME and press the ► or ENTER button. The SOURCE NAME menu will be displayed. (2) Use the ▲/▼ buttons on the SOURCE NAME menu to select the port to be named and press the ► button. The SOURCE NAME dialog will be displayed. Right side of the menu is blank until a name is specied.
SCREEN menu Item Description SOURCE NAME (continued) (6) The current name will be displayed on the rst line. Use the ▲/▼/◄/► buttons and the ENTER or INPUT button to select and enter characters. To erase 1 character at one time, press the RESET button or press the ◄ and INPUT button at the same time. Also if you move the cursor to DELETE or ALL CLEAR on screen and press the ENTER or INPUT button, 1 character or all characters will be erased. The name can be a maximum of 16 characters.
SCREEN menu Item Description The C.C. is the function that displays a transcript or dialog of the audio portion of a video, les or other presentation or other relevant sounds. It is required to have NTSC format video or 480i@60 format component video source supporting C.C. feature to utilize this function. It may not work properly, depending on equipment or signal source. In this case, please turn off the Closed Caption.
OPTION menu OPTION menu From the OPTION menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item, except for the items LAMP TIME and FILTER TIME. Then perform it according to the following table. Item Description AUTO SEARCH Using the ▲/▼ buttons turns on/off the automatic signal search function.
OPTION menu Item Description Using the ▲/▼ buttons adjusts the time to count down to automatically turn the projector off. Long (max. 99 minutes) Ù Short (min. 0 minute = DISABLE) AUTO POWER OFF USB TYPE B When the time is set to 0, the projector is not turned off automatically. When the time is set to 1 to 99, and when the passed time with no-signal or an unsuitable signal reaches at the set time, the projector lamp will be turned off.
OPTION menu Item Description LAMP TIME The lamp time is the usage time of the lamp, counted after the last resetting. It is shown in the OPTION menu. Pressing the RESET button on the remote control or the ► button of the projector displays a dialog. To reset the lamp time, select the OK using the ► button. CANCEL Ö OK • Please reset the lamp time only when you have replaced the lamp, for a suitable indication about the lamp. • For the lamp replacement, see the section Replacing the lamp ( 93).
OPTION menu Item Description MY BUTTON This item assigns one of the following functions to the ECO button on the control panel ( 5) and MY BUTTON 1/2 on the remote control ( 6). (1) Choose a button to assign a function from ECO, MY BUTTON-1 and MY BUTTON-2. Use the ▲/▼ buttons to select the desired function on the menu and press the ► button. (2) Then using the ▲/▼/◄/► buttons sets one of the following functions to the chosen button. Press the ENTER or INPUT button to save the setting.
OPTION menu Item Description MY BUTTON (continued) • PICTURE MODE: Changes the PICTURE MODE ( 31). • FILTER RESET: Displays the lter time reset conrmation dialogue ( 55). • TEMPLATE: Makes the template pattern selected to the TEMPLATE item ( 51) appear or disappear. • AV MUTE: Turns the picture and audio on/off. • RESOLUTION: Turns on/off the RESOLUTION dialog ( 42). • ECO MODE: Changes the ECO MODE ( 44). • BLANK: Turns on/off the blank function.
OPTION menu Item Description GHOST Adjust the settings using the ▲/▼ buttons to eliminate ghosting. SERVICE (continued) FILTER MESSAGE Use the ▲/▼ button to set the timer for notifying by the message when to replace the lter unit 100h Ù 200h Ù 500h Ù 1000h Ù 2000h Ù 3000h Ù 4000h Ù 5000h Ù OFF After choosing an item except OFF, the message “REMINDER *** HRS PASSED ....” will appear after the timer reaches the interval time set by this feature ( 99). When the OFF is chosen, the message will not appear.
OPTION menu Item Description Selecting this item displays COMMUNICATION menu. In this menu, you can congure the serial communication settings of the projector using the CONTROL port. • Select an item using the cursor buttons ▲/▼. Then pressing the ► button opens the submenu for the setting item you selected. Or, pressing the ◄ button instead of the ► button makes the menu back to the previous one without changing the setup. Each submenu can be operated as described above.
OPTION menu Item Description SERIAL SETTINGS Select the serial communication condition for the CONTROL port. BAUD RATE 4800bps Ù 9600bps Ù 19200bps Ù 38400bps PARITY NONE Ù ODD Ù EVEN • The BAUD RATE is xed to 19200bps and PARITY is xed NONE when the COMMUNICATION TYPE is set to OFF ( SERVICE (continued) (continued on next page) 60 59). TRANSMISSION METHOD COMMUNICATION Select the transmission method for communication (continued) by the NETWORK BRIDGE from the CONTROL port.
OPTION menu Item Description RESPONSE LIMIT TIME Select the time period to wait for receiving response data from other device communicating by the NETWORK BRIDGE and the HALF-DUPLEX through the CONTROL port. OFF Ù 1s Ù 2s Ù 3s SERVICE (continued) OFF: Select this mode if it is not required to check the responses from the device that the projector COMMUNICATION sends data to. In this mode, the projector can send out data from the computer continuously.
OPTION menu Item Description INFORMATION Selecting this item displays a dialog titled “INPUT_INFORMATION”. It shows the information about the current input. SERVICE (continued) • The “FRAME LOCK” message on the dialog means the frame lock function is working. • This item can't be selected for no signal and sync out. • When the MY TEXT DISPLAY is set to ON, the MY TEXT is displayed together with the input information in the INPUT_INFORMATION box ( 79).
NETWORK menu NETWORK menu Remember that incorrect network settings on this projector may cause trouble on the network. Be sure to consult with your network administrator before connecting to an existing access point on your network. Select “NETWORK” from the main menu to access the following functions. Select an item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or ENTER button on the remote control to execute the item.
NETWORK menu Item Description Use the ▲/▼ buttons to turn DHCP on/off. ON Ù OFF Select OFF when the network does not have DHCP enabled. To save the setting, press the ► button. DHCP (Dynamic Host • When the “DHCP” setting changes to “ON”, it &RQ¿JXUDWLRQ takes a little time to obtain IP address from DHCP Protocol) server.
NETWORK menu Item Description DATE AND TIME Use the ▲/▼/◄/► buttons to enter the Year (last two digits), Month, Date, Hour and Minute. • When this item is set, the same item in the WIRED SETUP menu is overwritten with the same setting ( 69). • The projector will override this setting and retrieve DATE AND TIME information from the Time server when SNTP is enabled.
NETWORK menu Item Description Use the ▲/▼ buttons to select the SSID to display the SSID menu. #1 DEFAULT Ù #2 DEFAULT Ù #3 DEFAULT #5 CUSTOM Ù #4 DEFAULT Select one of the DEFAULT (#1~#4) and press ► or ENTER button. WIRELESS SETUP (continued) (continued on next page) 66 SSID To adjust CUSTOM Press the ► or ENTER button when the # 5 CUSTOM is selected. The SSID #5 CUSTOM menu will be appeared. (1) The current SSID will be displayed on the rst line. If not yet written, the line will be blank.
NETWORK menu Item Description "Selecting this item displays the WIRELESS_INFORMATION dialog for viewing the wireless LAN settings." Use the ▲/▼ buttons to switch the page. The rst page shows the wireless LAN settings. The second and subsequent pages display the signal information of wireless LAN connection devices. WIRELESS INFORMATION • For details of PASSCODE, refer to the manual for “LiveViewer”. • Nothing (blank) is shown in the PROJECTOR NAME ( 70) and SSID ( 66) field until you setup those items.
NETWORK menu Item Description Selecting this item displays the WIRED SETUP menu for the wired LAN. Use the ▲/▼ buttons to select an item, and the ► or ENTER button on the remote control to perform the item. Use the ▲/▼ buttons to turn DHCP on/off. ON Ù OFF Select OFF when the network does not have DHCP enabled. To save the setting, press the ► DHCP (Dynamic Host button. &RQ¿JXUDWLRQ • When the “DHCP” setting changes to “ON”, it takes a little time to obtain IP address from DHCP Protocol) server.
NETWORK menu Item Description TIME DIFFERENCE WIRED SETUP (continued) DATE AND TIME Use the ▲/▼ buttons to enter the TIME DIFFERENCE. Set the same TIME DIFFERENCE as the one set on your computer. If unsure, consult your IT manager. Use the ► button to return to the menu after setting the TIME DIFFERENCE. • When this item is set, the same item in the WIRELESS SETUP menu is overwritten with the same setting ( 64). Use the ▲/▼/◄/► buttons to enter the Year (last two digits), Month, Date, Hour and Minute.
NETWORK menu Item Description PROJECTOR NAME (1) Use the ▲/▼ buttons on the NETWORK menu to select the PROJECTOR NAME and press the ► button. The PROJECTOR NAME dialog will be displayed. (2) The current PROJECTOR NAME will be displayed on the rst 3 lines. Particular projector name is pre-assigned by default. Use the ▲/▼/◄/► buttons and the ENTER or INPUT button to select and enter characters. To erase 1 character at one time, press the RESET button or press the ◄ and INPUT button at the same time.
NETWORK menu Item Description Selecting this item displays the MY IMAGE menu. Use the application to transfer the image data. It can be downloaded from the Hitachi web site. Use the ▲/▼ buttons to select an item which is a still image by the MY IMAGE (My Image Function in the Network Guide) and the ► or ENTER button to display the image. • The item without image stored cannot be selected. • The image names are each displayed in 16 characters or less.
NETWORK menu Item Description Selecting this item displays the PRESENTATION menu. Use ▲/▼ buttons to select one of the following items, then press ► or ENTER button to use the function. • To use Network Presentation, an exclusive application, "LiveViewer" is required. It can be installed from the bundled application CD. You can also download the latest version and relevant information from the Hitachi website (http://www.hitachi-america.us/digitalmedia or http://www.hitachidigitalmedia.com).
SECURITY menu Item Description MULTI PC MODE (continued) PRESENTATION (continued) • To change from Single PC mode to Multi PC mode, press ► button to choose OK in the dialog and press the ENTER or INPUT button. The display mode is changed. • For details on how to switch the display mode to Multi PC mode on your computer, refer to the manual for “LiveViwer”. • The Presenter mode setting of the selected computer becomes valid when the display mode is changed to Single PC mode.
SECURITY menu SECURITY menu This projector is equipped with security functions. From the SECURITY menu, items shown in the table below can be performed. To use SECURITY menu: User registration is required before using the security functions. Enter to the SECURITY menu 1. Press the ► button. The ENTER PASSWORD box will be displayed. 2. Use the ▲/▼/◄/► buttons to enter the registered password. The factory default password is as follows.
SECURITY menu Item Description The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten. 1 Turning on the MyScreen PASSWORD MyScreen PASSWORD 1-1 Use the ▲/▼ buttons on the SECURITY menu to select MyScreen PASSWORD and press the ► button to display the MyScreen PASSWORD on/ off menu. 1-2 Use the ▲/▼ buttons on the MyScreen PASSWORD on/off menu to select ON.
SECURITY menu Item Description PIN LOCK is a function which prevents the projector from being used unless a registered Code is input. 1 Turning on the PIN LOCK PIN LOCK 1-1 Use the ▲/▼ buttons on the SECURITY menu to select PIN LOCK and press the ► button or the ENTER button to display the PIN LOCK on/off menu. 1-2 Use the ▲/▼ buttons on the PIN LOCK on/ off menu to select ON and the Enter PIN Code box will be displayed. 1-3 Input a 4 part PIN code using the ▲/▼/◄/►, COMPUTER or INPUT button.
SECURITY menu Item Description If this function is set to ON and the vertical angle of the projector or the INSTALLATION setting is different from the previous recorded setting, the TRANSITION DETECTOR ON alarm will be displayed and the input signal will not be displayed. • To display the signal again, set this function OFF. • After about 5 minutes of displaying the TRANSITION DETECTOR ON alarm, the lamp will turn off.
SECURITY menu Item Description The MY TEXT PASSWORD function can prevent the MY TEXT from being overwritten. When the password is set for the MY TEXT; • The MY TEXT DISPLAY menu will be unavailable, which can prohibit changing the DISPLAY setting. • The MY TEXT WRITING menu will be unavailable, which can prevent the MY TEXT from being overwritten.
SECURITY menu Item Description MY TEXT DISPLAY (1) Use the ▲/▼ buttons on the SECURITY menu to select the MY TEXT DISPLAY and press the ► or ENTER button to display the MY TEXT DISPLAY on/off menu. (2) Use the ▲/▼ buttons on the MY TEXT DISPLAY on/off menu to select on or off. ON Ù OFF When it is set ON, the MY TEXT will be displayed on the START UP screen and the INPUT_ INFORMATION when the INFORMATION on the SERVICE menu is chosen.
Presentation tools Presentation tools The projector has the following two convenient tools that enable on-screen presentations easily and quickly: - PC-LESS Presentation ( below) - USB Display ( 89) PC-LESS Presentation The PC-LESS Presentation reads image and audio data from the storage media inserted into the USB TYPE A port and displays the image in the following modes. The PC-LESS Presentation can be started by selecting the USB TYPE A port as the input source.
Presentation tools PC-LESS Presentation (continued) >6XSSRUWHG ¿OH IRUPDW DQG LWV H[WHQVLRQ@ • JPEG (.jpeg, .jpg) * Progressive is not supported. • Bitmap (.bmp) * 16bit mode and compressed bitmap is not supported. • PNG (.png) * Interlace PNG is not supported. • GIF (.gif) NOTE • Files with a resolution larger than the following are not supported. CPX10WN, CPX11WN: 1024 x 768 CPWX12WN: 1280 x 800 (* Some computers may not support 1280 x 800.) • Files with a resolution smaller than 36x36 are not supported.
Presentation tools PC-LESS Presentation (continued) Operating by buttons or keys You can control the images on the Thumbnail screen with the remote control, control panel or Web Remote Control. The following functions can be supported while the Thumbnail is displayed. Button operation Functions The remote control Control panel Web Remote Control ▲/▼/◄/► ▲/▼/◄/► [▲]/[▼]/[◄]/[►] Moves cursor. PAGE UP PAGE DOWN - [PAGE UP] [PAGE DOWN] Switches pages.
Presentation tools PC-LESS Presentation (continued) Operating by the menu on the Thumbnail screen You can also control the images by using the menu on the Thumbnail screen. Item Functions Moves to an upper folder. SORT RETURN Allows you to sort les and folders as following. Press the ► cursor button or ENTER to return to the Thumbnail screen. NAME UP Sorts in ascending order by le name. NAME DOWN Sorts in descending order by le name. DATE UP Sorts in ascending order by le date.
Presentation tools PC-LESS Presentation (continued) NOTE • These operations are not accessible while the projector OSD is displayed. • The Thumbnail mode is able to display up to 20 les in one page. • It is not possible to change the input port by using the INPUT button when the Thumbnail screen, Slideshow, or Full Screen is displayed. • Some error icons will be displayed in the Thumbnail. This le seems to be broken or not supported format.
Presentation tools PC-LESS Presentation (continued) Full Screen Mode The Full Screen mode shows a full display image. To display in Full Screen mode, select an image in the Thumbnail screen. Then press the ENTER button on the remote control, the INPUT button on the control panel or click [ENTER] on the Web Remote Control. Full screen display Operations for still images The following operations are enabled in the Full Screen mode while a still image is displayed.
Presentation tools PC-LESS Presentation (continued) Slideshow Mode The Slideshow mode displays images in full screen and switches the images at intervals set in INTERVAL on the Thumbnail screen menu ( 83). You can start this function from the Slideshow menu. To display the Slideshow menu, select the SLIDESHOW button in the Thumbnail mode and press the ENTER button on the remote control, INPUT button on the control panel, or click [ENTER] on the Web Remote Control.
Presentation tools PC-LESS Presentation (continued) You can play the Slideshow at your desired conguration. Congure the Slideshow items in the Thumbnail. 1) RETURN : Returns to the thumbnail mode. 2) PLAY : Play the Slideshow. 3) START : Set the beginning number of the Slideshow. 4) STOP : Set the end number of the Slideshow. 5) INTERVAL : Sets the interval time for displaying still images during the Slideshow.
Presentation tools PC-LESS Presentation (continued) Playlist The Playlist is a DOS format text le, which decides the order of displayed still image les in the Thumbnail or Slideshow. The playlist le name is “playlist.txt” and it can be edited on a computer. It is created in the folder that contains the selected image les when the PC-LESS Presentation is started or the Slideshow is congured. [Example of “playlist.txt” ¿OHV@ START setting : STOP setting : INTERVAL setting : PLAY MODE setting : img001.
Presentation tools USB Display The projector can display images transferred from a computer via an USB cable ( 11). Hardware and software requirement for computer • OS: One of the following. (32 bit version only) Windows ® XP Home Edition /Professional Edition Windows Vista ® Home Basic /Home Premium /Business /Ultimate /Enterprise Windows ® 7 Starter /Home Basic /Home Premium /Professional / Ultimate / Enterprise • CPU: Pentium 4 (2.
Presentation tools USB Display (continued) This application will appear in the Windows notication area once it starts. You can quit the application from your computer by selecting “Quit” on the menu. NOTE • The “LiveViewer” (refer to the Network Guide) and this application cannot be used at the same time. If you connect your computer to the projector by using a USB cable while the “LiveViewer” is running, the following message will be displayed.
Presentation tools USB Display (continued) Right-Click menu The menu shown in the right will be displayed when you right-click the application icon in the Windows notication area. Display : The Floating menu is displayed, and the icon disappears from the Windows notication area. Quit : The application is closed, and the icon disappears from the Windows notication area. NOTE • If you wish to restart the application, you need to unplug the USB cable and plug it again.
Presentation tools USB Display (continued) Options window If you select the Option button on the Floating menu, the Options window is displayed. Optimize Performance The “LiveViewer Lite for USB” captures screenshots in JPEG data and sends them to the projector. The “LiveViewer Lite for USB” has two options that have different compression rate of JPEG data. Transmission speed Speed takes priority over Image quality. It makes JPEG compression rate higher.
Maintenance Maintenance Replacing the lamp A lamp has nite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended. To prepare a new lamp, make contact with your dealer and tell the lamp type number.
Maintenance Replacing the lamp (continued) Lamp warning HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE WARNING ►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
Maintenance Cleaning and replacing the air filter The air lter unit of this projector consists of a lter cover, two kinds of lters, and a lter frame. The new double large lters system is expected to function longer. However, please check and clean it periodically to keep ventilation needed for normal operation of the projector. When the indicators or a message prompts you to clean the air lter, comply with it as soon as possible. Replace the lters when they are damaged or too soiled.
Maintenance Cleaning and replacing the air lter (continued) Turn the projector on and reset the lter time using the FILTER TIME item in 9. the EASY MENU. (1) Press the MENU button to display a menu. (2) Point at the FILTER TIME using the ▼/▲ button, then press the ► button. A dialog will appear. (3) Press the ► button to select “OK” on the dialog. It performs resetting the lter time.
Maintenance Other care Inside of the projector In order to ensure the safe use of your projector, please have it cleaned and inspected by your dealer about once every year. Caring for the lens If the lens is awed, soiled or fogged, it could cause deterioration of display quality. Please take care of the lens, being cautious of handling. the projector off, and unplug the power cord. Allow the projector to cool 1. Turn sufciently. making sure that the projector is cool adequately, lightly wipe the lens 2.
Troubleshooting Troubleshooting If an abnormal operation should occur, stop using the projector immediately. WARNING ►Never use the projector if abnormal operations such as smoke, Troubleshooting strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact to your dealer or service company.
Troubleshooting Related messages (continued) Message Description The internal temperature is rising. Please turn the power off, and allow the projector to cool down at least 20 minutes. After having conrmed the following items, please turn the power ON again.
Troubleshooting Regarding the indicator lamps When operation of the LAMP, TEMP and POWER indicators differs from usual, check and cope with it according to the following table. POWER LAMP TEMP Description indicator indicator indicator Turned Turned The projector is in a standby state. Lighting Please refer to the section “Power on/off”. off off In Orange Blinking In Green Turned off Turned off The projector is warming up. Lighting In Green Turned off Turned off The projector is in an on state.
Troubleshooting Regarding the indicator lamps (continued) POWER LAMP TEMP indicator indicator indicator Description There is a possibility that the interior portion has become heated. Blinking In Red or Lighting In Red Turned off Lighting In Red Please turn the power off, and allow the projector to cool down at least 20 minutes. After the projector has sufciently cooled down, please make conrmation of the following items, and then turn the power on again.
Troubleshooting Resetting all settings When it is hard to correct some wrong settings, the FACTORY RESET function of SERVICE item in OPTION menu ( 62) can reset all settings (except settings such as LANGUAGE, LAMP TIME, FILTER TIME, FILTER MESSAGE, SECURITY and NETWORK) to the factory default. Be sure to set ALTITUDE after resetting all the settings ( 57).
Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Phenomenon Cases not involving a machine defect The signal cables are not correctly connected. Correctly connect the audio cables. 10 ~ 14 The MUTE function is working. Restore the sound pressing MUTE or VOLUME +/button on the remote control. 21 The volume is adjusted to an extremely low level. Adjust the volume to a higher level using the menu function or the remote control. Sound does not come out.
Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Phenomenon Cases not involving a machine defect The projector does not recognize the USB storage device inserted into USB TYPE A port. Use the REMOVE USB function rst, remove the USB No pictures are storage device, and then insert it into the port again. displayed.
Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Phenomenon Some kind of image degradation such as ickering or stripes appear on screen. The sound or image is unstable or is output intermittently. The computer connected to the USB TYPE B port of the projector does not start up. Cases not involving a machine defect When the projector is operating in Eco mode, ÀLFNHULQJ PD\ DSSHDU RQ VFUHHQ Set ECO MODE to NORMAL, and set AUTO ECO MODE to OFF, in the SETUP menu.
Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Phenomenon Schedule function does not work When the projector is connected to wired LAN, it powers off and on as described below. Powers off POWER indicator blinks in orange a few times Goes into standby mode Cases not involving a machine defect Reference page The SAVING function is working. Select NORMAL for STANDBY MODE item in the SETUP menu. 45 The internal clock has been reset.
Specifications Specications Please see the 6SHFL¿FDWLRQV in the User’s Manual (concise) which is a book. End User License Agreement for the Projector Software • Software in the projector consists of the plural number of independent software modules and there exist our copyright or/and third party copyrights for each of such software modules. • Be sure to read “End User License Agreement for the Projector Software” which is separated document.
Projector CPX10WN/CPX11WN/ CPWX12WN User's Manual (detailed) Network Guide Thank you for purchasing this product. This manual is intended to explain only the network function. For proper use of this product, please refer to this manual and the other manuals for this product. WARNING ►Before using this product, be sure to read all manuals for this product. After reading them, store them in a safe place for future reference.
Contents Contents Caution .......................................................................................... 4 1. Connection to the network ...................................................... 5 1.1 System requirements ................................................................................. 5 1.1.1 Required equipment preparation ..................................................................................... 5 1.1.2 Hardware and software requirement for computer ....................
Contents 6. Network Bridge Function ....................................................... 52 6.1 Connecting devices .................................................................................. 6.2 Communication setup ............................................................................... 6.3 Communication port ................................................................................. 6.4 Transmission method .............................................................................
Caution Caution To use the wireless network function of this projector, the designated USB wireless adapter that is sold as an option is required. For precautions according to the standards and laws, refer to the documents that come with the adapter. [Restriction on plugging and unplugging the USB wireless adapter] Before you insert or pull out the USB wireless adapter from the projector, turn off the power of the projector and pull out the power cord’s plug from the outlet.
1. Connection to the network 1. Connection to the network 1.1 System requirements 1.1.1 Required equipment preparation The following equipments are required to connect the projector to your computer through the network. Ŷ &RPPRQ The projector: 1 unit, Computer : minimum 1 set Ŷ 'HSHQGLQJ RQ KRZ \RX ZDQW WR FRQQHFW 1) For the wired connection *1 LAN cable (CAT-5 or greater): 1 piece 2) For the wireless connection *2 - Projector side IEEE802.
1. Connection to the network 1.1 System requirements (continued) NOTE • The network communication control is disabled while the projector is in standby mode if the STANDBY MODE item is set to SAVING. Please connect the network communication to the projector after setting the STANDBY MODE to NORMAL. ( SETUP menu in the Operating Guide) • You can get the latest version of the applications for the network functions of the projector and the latest information for this product from the Hitachi website.
1. Connection to the network 1.3 Manual network connection setting - Wired LAN This section explains how to set it up manually. 1.3.1 Equipments connection Connect the projector and a computer with a LAN cable. * Before connecting with an existing network, contact the network administrator. Next, check the following computer settings. 1.3.2 Network settings This is the explanation of network connection settings for Windows® 7 and Internet Explorer. 1) Log on to Windows® 7 as administrator authority.
1. Connection to the network 1.3 Manual network connection setting - Wired LAN - (continued) 5) Right-click "Local Area Connection" to open the menu, and select "Properties". 6) Select "Internet Protocol Version 4 (TCP/IPv4)" and click [Properties]. 7) Select "Use the following IP address" and congure the IP address, Subnet mask and Default gateway for the computer accordingly.
1. Connection to the network 1.3 Manual network connection setting - Wired LAN - (continued) [About IP address] Ŷ 6HWWLQJ PDQXDOO\ The Network address portion of the IP address setting on your computer must be the same as the setting on the projector.Also, the entire IP address on the computer must not overlap with that of the other devices on the same network, including the projector. For example The projector’s settings are as follows. IP address: 192.168.1.254 Subnet mask: 255.255.255.
1. Connection to the network 1.3 Manual network connection setting - Wired LAN - (continued) 1.3.3 “Internet Option” setting 1) Click “Internet Options” in “Network and Sharing Center” window to open “Internet Properties” window. 2) Click “Connections” tab and then click [LAN settings] button to open “Local Area Network (LAN) Settings”. 3) Uncheck all boxes in “Local Area Network (LAN) Settings” window. After setting is complete, click [OK] to close the window.
1. Connection to the network 1.4 Manual network connection setting - Wireless LAN Using the designated USB wireless adapter (option) on the projector enables the projector and computer to communicate in both the Ad-Hoc and Infrastructure modes. This section is intended to explain how to set up wireless LAN connection manually. 1.4.1 Preparation for wireless LAN connection Fig. 1.4.1.a Without an access point communication (Ad-Hoc) Fig. 1.4.1.
1. Connection to the network 1.4 Manual network connection setting - Wireless LAN - (continued) 1.4.2 Wireless LAN connection set up Using wireless LAN utility for Windows® 7 standard. Wireless LAN initial settings for the projector is as follows. Connection Control : Ad-Hoc SSID : wireless Channel :1 Encryption rating : None IP address : 192.168.10.254 * You can change these settings via a web browser on your computer or from the menu of the projector. Refer to the item 3.1.
1. Connection to the network 1.4 Manual network connection setting - Wireless LAN - (continued) 4) Select "Use the following IP address" and congure the IP address, Subnet mask and Default gateway for the computer accordingly. After setting is complete, click [OK] to close the window. [About IP address] The Network address portion of the IP address setting on your computer must be the same as the setting on the projector.
1. Connection to the network 1.4 Manual network connection setting - Wireless LAN - (continued) 5) Right-click "Wireless Network Connection" to open the menu, and select "Connect / Disconnect". 6) From the connectable wireless networks, select the SSID of the projector (set to "wireless" by default), and click [Connect]. If you have enabled encryption, a window asking for input of the encryption key will be displayed. Input the preset key.
2. Network Presentation 2. Network Presentation The projector can display or play back the computer screen images and audio data that are transmitted through the network. This Network Presentation feature helps you to smoothly make your presentations and conduct conferences. Wireless LAN Wired LAN To use Network Presentation, an exclusive application, "LiveViewer" is required. It can be installed from the bundled application CD.
3. Web Control 3. Web Control You can adjust or control the projector via a network from a web browser on a computer that is connected to the same network. NOTE • Internet Explorer® 6.0 or later is required. • If JavaScript® is disabled in your web browser conguration, you must enable JavaScript® in order to use the projector web pages properly. See the Help les for your web browser for details on how to enable JavaScript®. • It is recommended that all web browser updates are installed.
3. Web Control 3.1 Projector Web Control 3.1.1 Logon To use the Projector Web Control function, you need to logon with your user name and password. Below are the factory default settings for user name and password. User name Password Administrator Logon window Enter your user name and password, and then click the [OK]. If you logon successfully, the screen below will be displayed. Main menu Click the desired operation or conguration item on the main menu.
3. Web Control 3.1 Projector Web Control (continued) 3.1.2 Network Information Displays the projector’s current network conguration settings. 'HVFULSWLRQ Item Common Information Projector Name Wireless Information Displays the projector name settings. Displays the current settings of wireless LAN. Mode Displays the mode of wireless LAN communication. '+&3 Displays the DHCP setting. IP Address Displays the IP address. Subnet Mask Displays the subnet mask.
3. Web Control 3.1 Projector Web Control (continued) 3.1.3 Network Settings Displays and congures network settings. Item Common Setup 'HVFULSWLRQ Displays information common to both wireless and wired LAN. Projector Name Congures the name of the projector. The length of the Projector Name can be up to 64 alphanumeric characters. Only alphabets, numbers and following symbols can be used. !"#$%&'()*+,-./:;<=>?@[\]^_`{|}~ and space. Particular projector name is pre-assigned by default.
3. Web Control 3.1 Projector Web Control - Network Settings (continued) 'HVFULSWLRQ Item Wireless Setup Congures the wireless LAN settings. Mode Select "AD-HOC" or "Infrastructure". ,3 &RQ¿JXUDWLRQ Congures network settings. '+&3 21 Enables DHCP. '+&3 2)) Disables DHCP. IP Address Congures the IP address when DHCP is disabled. Subnet Mask Congures the subnet mask when DHCP is disabled. 'HIDXOW Gateway Congures the default gateway when DHCP is disabled.
3. Web Control 3.1 Projector Web Control - Network Settings (continued) 'HVFULSWLRQ Item Wired Setup ,3 &RQ¿JXUDWLRQ Congures the wired LAN settings. Congures network settings. '+&3 21 Enables DHCP. '+&3 2)) Disables DHCP. IP Address Congures the IP address when DHCP is disabled. Subnet Mask Congures the subnet mask when DHCP is disabled. 'HIDXOW Gateway Congures the default gateway when DHCP is disabled.
3. Web Control 3.1 Projector Web Control (continued) 3.1.4 Port Settings Displays and congures communication port settings. Item Network Control Port1 (Port:23) Congures command control port 1 (Port:23). Port open Click the [Enable] check box to use port 23. Authentication Click the [Enable] check box when authentication is required for this port. Network Control Port2 (Port:9715) Congures command control port 2 (Port:9715). Port open Click the [Enable] check box to use port 9715.
3. Web Control 3.1 Projector Web Control - Port Settings (continued) 'HVFULSWLRQ Item SNMP Port Congures the SNMP port. Port open Click the [Enable] check box to use SNMP. Trap address Congures the destination of the SNMP Trap in IP format. • The address allows not only IP address but also domain name if the valid DNS server is setup in the Network Settings. The maximum length of host or domain name is up to 255 characters. 'RZQORDG 0,% ¿OH Downloads a MIB le from the projector.
3. Web Control 3.1 Projector Web Control (continued) 3.1.5 Mail Settings Displays and congures e-mail addressing settings. 'HVFULSWLRQ Item Send Mail Click the [Enable] check box to use the e-mail function. Congure the conditions for sending e-mail under the Alert Settings. SMTP Server Address Congures the address of the mail server in IP format. • The address allows not only IP address but also domain name if the valid DNS server is setup in the Network Settings.
3. Web Control 3.1 Projector Web Control (continued) 3.1.6 Alert Settings Displays and congures failure & alert settings. 'HVFULSWLRQ Item Cover Error The lamp cover has not been properly xed. Fan Error The cooling fan is not operating. Lamp Error The lamp does not light, and there is a possibility that interior portion has become heated. Temp Error There is a possibility that the interior portion has become heated. Air Flow Error The internal temperature is rising.
3. Web Control 3.1 Projector Web Control - Alert Settings (continued) The Alert Items are shown below. 'HVFULSWLRQ Item Alarm Time Congures the time to alert. (Only Lamp Time Alarm and Filter Time Alarm.) SNMP Trap Click the [Enable] check box to enable SNMP Trap alerts. Send Mail Click the [Enable] check box to enable e-mail alerts. (Except Cold Start and Authentication Failure.) Mail Subject Congures the subject line of the e-mail to be sent.
3. Web Control 3.1 Projector Web Control (continued) 3.1.7 Schedule Settings Displays and congures schedule settings. Item 'HVFULSWLRQ 'DLO\ Congures the daily schedule. Sunday Congures the Sunday schedule. Monday Congures the Monday schedule. Tuesday Congures the Tuesday schedule. Wednesday Congures the Wednesday schedule. Thursday Congures the Thursday schedule. Friday Congures the Friday schedule. Saturday Congures the Saturday schedule.
3. Web Control 3.1 Projector Web Control - Schedule Settings (continued) The schedule settings are shown below. 'HVFULSWLRQ Item Schedule Click the [Enable] check box to enable the schedule. 'DWH 0RQWK 'D\ Congures the month and date. This item appears only when Specic date (No. 1-5) is selected. Click the [Apply] button to save the settings. The current event settings are displayed on the schedule list. To add additional functions and events, set the following items.
3. Web Control 3.1 Projector Web Control - Schedule Settings (continued) NOTE • After the projector is moved, check the date and time set for the projector before conguring the schedules. • The internal clock’s time may not remain accurate. Using SNTP is recommended to maintain accurate time.
3. Web Control 3.1 Projector Web Control (continued) 3.1.8 Date/Time Settings Displays and congures the date and time settings. 'HVFULSWLRQ Item &XUUHQW 'DWH Congures the current date in year/month/day format. Current Time Congures the current time in hour:minute:second format. 'D\OLJKW 6DYLQJV 7LPH Click the [ON] check box to enable daylight savings time and set the following items. Congures the date and time daylight savings time begins.
3. Web Control 3.1 Projector Web Control - Date/Time Settings (continued) 'HVFULSWLRQ Item Time difference Congures the time difference. Set the same time difference as the one set on your computer. If unsure, consult your IT manager. SNTP Click the [ON] check box to retrieve Date and Time information from the SNTP server and set the following items. Congures the SNTP server address in IP format.
3. Web Control 3.1 Projector Web Control (continued) 3.1.9 Security Settings Displays and congures passwords and other security settings. 'HVFULSWLRQ Item User Account Congures the user name and password. User name Congures the user name. The length of the text can be up to 32 alphanumeric characters. Password Congures the password. The length of the text can be up to 255 alphanumeric characters. Re-enter Password Reenter the above password for verication.
3. Web Control 3.1 Projector Web Control (continued) 3.1.10 Projector Control The items shown in the table below can be performed using the Projector Control menu. Select an item with the mouse. Most of the items have a submenu. Refer to the table below for details. Controls the projector. NOTE • The setting value may not match with the actual value if the user changes the value manually. In that case, please refresh the page by clicking the [Refresh] button.
3. Web Control 3.1 Projector Web Control - Projector Control (continued) Item PICTURE BRIGHTNESS CONTRAST GAMMA COLOR TEMP COLOR TINT SHARPNESS MYMEMORY SAVE MYMEMORY RECALL IMAGE ASPECT OVER SCAN V POSITION H POSITION H PHASE H SIZE $872 $'-867 EXECUTE INPUT PROGRESSIVE 9,'(2 15 COLOR SPACE 9,'(2 )250$7 6 9,'(2 9,'(2 )250$7 9,'(2 +'0, )250$7 +'0, 5$1*( COMPUTER IN COMPUTER IN1 COMPUTER IN COMPUTER IN2 FRAME LOCK COMPUTER IN1 FRAME LOCK COMPUTER IN2 )5$0( /2&.
3. Web Control 3.1 Projector Web Control - Projector Control (continued) Item SETUP AUTO KEYSTONE EXECUTE KEYSTONE V $872 (&2 02'( (&2 02'( INSTALLATION 67$1'%< 02'( MONITOR OUT COMPUTER IN1 MONITOR OUT COMPUTER IN2 'HVFULSWLRQ Performs the automatic keystone distortion setting. Adjusts the vertical keystone distortion setting. Turns on/off the automatic eco mode function. Selects the eco mode. Selects the installation status. Selects the standby mode.
3. Web Control 3.1 Projector Web Control - Projector Control (continued) Item $8',2 VOLUME SPEAKER $8',2 6285&( COMPUTER IN1 $8',2 6285&( COMPUTER IN2 $8',2 6285&( /$1 $8',2 6285&( 86% TYPE A $8',2 6285&( 86% TYPE B $8',2 6285&( +'0, $8',2 6285&( 6 9,'(2 $8',2 6285&( 9,'(2 $8',2 6285&( $8',2 287 67$1'%< +'0, $8',2 SCREEN LANGUAGE MENU POSITION V MENU POSITION H BLANK START UP MyScreen Lock MESSAGE TEMPLATE & & ',63/$< & & 02'( C.C.
3. Web Control 3.1 Projector Web Control - Projector Control (continued) Item OPTION AUTO SEARCH AUTO KEYSTONE ',5(&7 32:(5 21 AUTO POWER OFF USB TYPE B MY BUTTON-1 MY BUTTON-2 ECO (CONTROL PANEL) MY SOURCE 'HVFULSWLRQ Turns the automatic signal search function on/off. Turns the automatic keystone distortion correction function on/off. Turns the direct power on function on/off. Congures the timer to shut off the projector when no signal is detected. Selects the USB TYPE B setting.
3. Web Control 3.1 Projector Web Control - Projector Control (continued) The items shown in the table below can be performed using the Projector Control menu. Click the [Quit Presenter Mode]. Item 'HVFULSWLRQ SERVICE Quit Presenter Mode 38 Quit compulsorily from the Presenter mode.
3. Web Control 3.1 Projector Web Control (continued) 3.1.11 Remote Control You can use your Web browser to control the projector. The functions on the bundled remote control are assigned to the Web Remote Control screen. • Do not attempt to control the projector with the projector’s remote control and via your Web browser at the same time. It may cause some operational errors in the projector. 'HVFULSWLRQ Item POWER Assigned the same operation as 67$1'%< 21 button.
3. Web Control 3.1 Projector Web Control (continued) 3.1.12 Projector Status Displays the settings and status of the projector. Item 'HVFULSWLRQ Error Status Displays the current error status Lamp Time Displays the usage time for the current lamp. Filter Time Displays the usage time for the current lter. Power Status Displays the current power status. Input Status Displays the current input signal source. Blank On/Off Displays the current Blank on/off status.
3. Web Control 3.1 Projector Web Control (continued) 3.1.13 Network Restart Restarts the projector’s network connection. Item Restart 'HVFULSWLRQ Restarts the projector’s network connection in order to activate new conguration settings. NOTE • Restarting requires you to re-log on in order to further control or congure the projector via a web browser. Wait 30 seconds or more after clicking the [Restart] button to log on again.
3. Web Control 3.2 Crestron e-Control® Tab The Main window as shown above is displayed at rst. However, if you have enabled User Password on the Tools window ( 46), a dialog prompting you to enter the password as shown on the right will be displayed, and no operation is enabled until you have entered the password. After entering the preset password, the dialog disappears and the Main window will be displayed.
3. Web Control 3.2 Crestron e-Control® (continued) 3.2.1 Main window 1 4 2 3 You can operate the basic controls of the projector on this screen. NOTE • If the projector is in the standby mode, only the Power button can be operated. 1 Click a button and operate as follows. Button Power Vol -/ Vol + Mute 'HVFULSWLRQ Turns the power on/off. Adjusts the volume setting. Turns Mute on/off. 2 Sources List You can click a button to switch the input channel.
3. Web Control 3.2 Crestron e-Control® - Main window (continued) 3 Click a button and operate as follows. To show the hidden buttons, click the ◄ / ► icons at the left and right ends. Button Freeze Contrast Brightness Color Sharpness Magnify Auto Blank 'HVFULSWLRQ Turns Freeze on/off. Adjusts the contrast setting. Adjusts the brightness setting. Adjusts the color setting. Adjusts the sharpness setting. Controls the magnication setting using the [+] / [-] buttons.
3. Web Control 3.2 Crestron e-Control® (continued) 3.2.2 Tools window 2 1 4 5 3 Congures the settings between the projector and Crestron® control system. Click the [Exit] button to return to the Main window. NOTE • If two-byte characters are used, the input text or numbers cannot be set correctly. • All items on this window cannot be left blank. 1 Crestron Control Congures the settings of Crestron® control system devices.
3. Web Control 3.2 Crestron e-Control® - Tools window (continued) 3 Projector (continued) Congures the network settings of the projector. Item '+&3 IP Address 'HVFULSWLRQ Enables DHCP. Congures the IP address when DHCP is disabled. Subnet Mask Congures the subnet mask when DHCP is disabled. 'HIDXOW *DWHZD\ '16 6HUYHU Congures the default gateway when DHCP is disabled. Congures the DNS server address. To apply the settings, click the [Send] button. 4 User Password Congures the User Password.
3. Web Control 3.2 Crestron e-Control® (continued) 3.2.3 Info window 1 2 Displays the settings and status of the projector. Click the [Exit] button to return to the Main window. 1 Projector Information Item Projector Name Location MAC Address Resolution Lamp Hours Assigned To: 'HVFULSWLRQ Displays the projector name settings. Displays the location name of the projector. Displays the wired LAN MAC address of the projector.
3. Web Control 3.2 Crestron e-Control® (continued) 3.2.4 Help Desk window Sends/receives messages to/from the administrator for Crestron RoomView® Express. Button Send 48 'HVFULSWLRQ Sends a message. Check the received message.
3. Web Control 3.2 Crestron e-Control® (continued) 3.2.5 Emergency Alert When the administrator for Crestron RoomView® Express sends out an alert message, it will be displayed on the screen. You can reply to the alert message via a chat format. Input a message in the box below the alert message, and click the [Send] button. NOTE • For details of Emergency Alert, refer to the manual of Crestron RoomView® Express.
4. My Image Function 4. My Image Function The projector can display still images that are transferred via the network. Transfer image data 1 2 3 4 Display image data (ex. ) MY IMAGE transmission requires an exclusive application for your computer. Use the application to transfer the image data. It can be downloaded from the Hitachi web site (http://www.hitachi-america.us/ digitalmedia or http://www.hitachidigitalmedia.com).
5. Messenger Function 5. Messenger Function The projector can display text data transferred via the network on the screen and play back audio data inside the projector. The text data can be displayed on the screen in two ways that displays the text transferred from the computer on real time, and the other chooses and displays the text data from the ones once stored in the projector. Transfer text data 1 2 3 4 12 Display text data (ex.
6. Network Bridge Function 6. Network Bridge Function This projector is equipped with the NETWORK BRIDGE function to perform mutual conversion of a network protocol and a serial interface. By making use of the NETWORK BRIDGE function, a computer that is connected to the projector via wireless or wired LAN is able to control an external device via RS-232C communication using the projector as a network terminal.
6. Network Bridge Function 6.2 Communication setup To congure the setup of the communication using NETWORK BRIDGE for the projector, use items in the COMMUNICATION menu. Open the menu of the projector and select the OPTION - SERVICE - COMMUNICATION menu. ( OPTION menu > SERVICE > COMMUNICATION in the Operating Guide) 1) In the COMMUNICATION TYPE menu, select NETWORK BRIDGE (WIRELESS or WIRED depending on the type of connection you use) for the CONTROL port.
6. Network Bridge Function 6.4 Transmission method The transmission method can be selected from the menus, only when the NETWORK BRIDGE is selected for the COMMUNICATION TYPE. ( OPTION menu > SERVICE > COMMUNICATION in the Operating Guide) HALF-DUPLEX FULL-DUPLEX 6.4.1 HALF-DUPLEX This method lets the projector make two way communication, but only one direction, either transmitting or receiving data, is allowed at a time.
6. Network Bridge Function 6.4 Transmission method (continued) NOTE • With using the HALF-DUPLEX method, the projector can send out 254 byte data as maximum at once. • If it is not required to monitor the response data from an external device and the RESPONSE LIMIT TIME is set to OFF, the projector can receive the data from the computer and send it out to an external device continuously. The OFF is selected as the default setting. 6.4.
7. Other Functions 7. Other Functions 7.1 E-mail Alerts The projector can automatically send an alert message to the specied e-mail addresses when the projector detects a certain condition that is requiring maintenance or detected an error. NOTE • Up to ve e-mail addresses can be specied. • The projector may be not able to send e-mail if the projector suddenly loses power. Mail Settings ( 24) To use the projector’s e-mail alert function, please congure the following items through a web browser.
7. Other Functions 7.1 E-mail Alerts (continued) 5) Click the [Alert Settings] on the main menu to congure the E-mail Alerts settings. 6) Select and congure each alert item. Refer to item 3.1.6 Alert Settings ( 31) for further information. 7) Click the [Apply] button to save the settings.
7. Other Functions 7.2 Projector Management using SNMP The SNMP (Simple Network Management Protocol) enables to manage the projector information, which is a failure or warning status, from the computer on the network. The SNMP management software will be required on the computer to use this function. NOTE • It is recommended that SNMP functions be carried out by a network administrator. • SNMP management software must be installed on the computer to monitor the projector via SNMP.
7. Other Functions 7.3 Event Scheduling The scheduling function enables to setup scheduled events including power on / power off. It enables to be “self-management” projector. NOTE • You can schedule the following control events: Power, Input Source, My Image, Messenger, Slideshow. ( 28) • The power on / off event has the lowest priority among the all events that are dened at the same time. • There are 3 types of Scheduling, 1) daily 2) weekly 3) specic date.
7. Other Functions 7.3 Event Scheduling(continued) Schedule Settings ( 27) Schedule settings can be congured from a web browser. Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter “http://192.168.1.10/” into the address bar of the web browser, and select Projector Web Control from the selection window. 2) Enter your user name and password, and then click the [OK]. 3) Click the [Schedule Settings] on the main menu and select the required schedule item.
7. Other Functions 7.3 Event Scheduling(continued) Date/Time Settings ( 30) The Date/Time setting can be adjusted via a web browser. Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter “http://192.168.1.10/” into the address bar of the web browser, and select Projector Web Control from the selection window. 2) Enter your user name and password, and then click the [OK]. 3) Click the >'DWH 7LPH 6HWWLQJV@ on the main menu and congure each item.
7. Other Functions 7.4 Command Control via the Network You can congure and control the projector via the network using RS-232C commands. Communication Port The following two ports are assigned for the command control. TCP #23 (Network Control Port1 (Port: 23)) TCP #9715 (Network Control Port2 (Port: 9715)) NOTE • Command control is available only via the specied port above. Command Control Settings ( 22) Congure the following items from a web browser when command control is used.
7. Other Functions 7.4 Command Control via the Network (continued) When the authentication setting is enabled, the following settings are required. ( 32) 7) Click the [Security Settings] on the main menu. 8) Click the [Network Control] and enter the desired authentication password. * See NOTE. 9) Click the [Apply] button to save the settings.
7. Other Functions 7.4 Command Control via the Network (continued) Command Format Command formats differ among the different communication ports. ● TCP #23 You can use the RS-232C commands without any changes. The reply data format is the same as the RS-232C commands. ( RS-232C Communication in the Operating Guide - Technical) However, the following reply will be sent back in the event of authentication failure when authentication is enabled.
7. Other Functions 7.4 Command Control via the Network (continued) Reply Data format The connection ID (the data is same as the connection ID data on the sending data format) is attached to the RS-232C commands reply data.
7. Other Functions 7.4 Command Control via the Network (continued) Automatic Connection Break The TCP connection will be automatically disconnected after there is no communication for 30 seconds after being established. Authentication The projector does not accept commands without authentication success when authentication is enabled. The projector uses a challenge response type authentication with an MD5 (Message Digest 5) algorithm.
7. Other Functions 7.5 Crestron RoomView® Crestron RoomView® is a multi-user resource management program provided by Crestron Electronics, Inc. It is an application for managing and controlling the projector and other AV devices collectively. For details of Crestron RoomView®, refer to the Crestron® website. URL: http://www.crestron.com The following communication interfaces can be used to manage the entire facility.
8. Troubleshooting 8. Troubleshooting Problem Can't communicate Others - Information from the projector to computer is not correct or completed - The projector does not respond 68 Likely Cause Things to Check Reference Page Number Weak radio signal • Bring the computer and projector closer together. • Radio waves won’t go through concrete and metal (steel doors, etc.) – Cannot communicate due to congure wireless / encryption settings.
9. Specifications 9. Specications Item Specifications Control software Dedicated computer application and Web browser Corresponding protocol TCP/IP, DHCP client and HTTP server Network Wireless LAN (IEEE802.
10. Warranty and after-sales service 10. Warranty and after-sales service If a problem occurs with the equipment, please read 8. Troubleshooting ( 68) section rst and review all suggested check points. After that, please contact your dealer or service company, if you still have the problem. They will tell you what warranty condition is applied.
Projector CPX10WN/CPX11WN/CPWX12WN User's Manual (detailed) Operating Guide – Technical Example of PC signal Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode 37.9 85.0 VESA TEXT 720 x 400 640 x 480 31.5 59.9 VESA VGA (60Hz) 640 x 480 37.9 72.8 VESA VGA (72Hz) 640 x 480 37.5 75.0 VESA VGA (75Hz) 640 x 480 43.3 85.0 VESA VGA (85Hz) 800 x 600 35.2 56.3 VESA SVGA (56Hz) 800 x 600 37.9 60.3 VESA SVGA (60Hz) 800 x 600 48.1 72.2 VESA SVGA (72Hz) 800 x 600 46.9 75.
Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some PC models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Active video (C) Data H. Sync. Sync (A) Back porch (b) Front porch (d) Active video (c) Data V. Sync. Sync (a) Resolution Horizontal signal timing (μs) Vertical signal timing (lines) Signal mode (H x V) (A) (B) (C) (D) (a) (b) (c) (d) 2.0 3.
Connection to the ports Connection to the ports NOTICE ►Use the cables with straight plugs, not L-shaped ones, as the input ports of the projector are recessed. HDMI USB TYPE A DC5V 0.5A USB TYPE B A B COMPUTER IN1 COMPUTER IN2 C S-VIDEO VIDEO LAN AC IN AUDIO OUT MONITOR OUT AUDIO IN1 AUDIO IN2 CONTROL A COMPUTER IN1, B COMPUTER IN2, C MONITOR OUT D-sub 15pin mini shrink jack • Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) • H/V. sync.
Connection to the ports (continued) D F HDMI USB TYPE A DC5V 0.5A USB TYPE B COMPUTER IN1 LAN AC IN AUDIO IN1 S-VIDEO VIDEO E AUDIO OUT MONITOR OUT COMPUTER IN2 AUDIO IN2 CONTROL D S-VIDEO Mini DIN 4pin jack 4 2 3 1 • System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL (60Hz) Pin Signal 1 Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator Color signal 0.300Vp-p (PAL/SECAM, burst) 75Ω terminator 2 Brightness signal, 1.
Connection to the ports (continued) G HDMI USB TYPE A DC5V 0.5A LAN AC IN USB TYPE B COMPUTER IN1 I H AUDIO OUT MONITOR OUT S-VIDEO VIDEO COMPUTER IN2 AUDIO IN1 AUDIO IN2 CONTROL G AUDIO IN1, H AUDIO IN2 Ø3.5 stereo mini jack • 200 mVrms 47kΩ terminator I AUDIO OUT Ø3.
Connection to the ports (continued) L K HDMI USB TYPE A DC5V 0.5A M USB TYPE B COMPUTER IN1 J AUDIO IN1 S-VIDEO VIDEO LAN AC IN AUDIO OUT MONITOR OUT COMPUTER IN2 AUDIO IN2 CONTROL J CONTROL D-sub 9pin plug • About the details of RS-232C communication, please refer to the next chapter.
Connection to the ports (continued) To input component video signal to COMPUTER IN ports ex. D-sub plug RCA plugs HDMI USB TYPE A DC5V 0.5A USB TYPE B COMPUTER IN1 S-VIDEO VIDEO LAN AC IN AUDIO OUT MONITOR OUT RCA connectors COMPUTER IN2 AUDIO IN1 AUDIO IN2 Y CB/PB CR/PR COMPONENT VIDEO OUT CONTROL VCR/DVD/Blu-ray Disc player To input component video signal to the COMPUTER IN1 or COMPUTER IN2 port of the projector, use a RCA to D-sub cable or adapter.
RS-232C Communication RS-232C Communication When the projector connects to the computer by RS-232C communication, the projector can be controlled with RS-232C commands from the computer. For details of RS-232C commands, refer to RS-232C Communication / Network command table ( 17). Connection 1. Turn off the projector and the computer. the projector's CONTROL port and the computer's RS-232C port 2. Connect with a RS-232C cable (cross). Use the cable that fullls the specication 3. 4. shown in gure.
RS-232C Communication (continued) Communication settings 1. Protocol 19200bps,8N1 2. Command format ("h" shows hexadecimal) Byte Number 0 1 Command Action 2 3 4 5 6 7 8 9 Header code Packet L H 10 11 12 Data Header Data size CRC ag Action Type Setting code L L L L L H H H H H Change setting to desired value [(bL)(bH)] by [(eL)(eH)]. (aL) (aH) 01h 00h (bL) (bH) (cL) (cH) Read projector internal setup value [(bL) (bH)] .
RS-232C Communication (continued) 3. Response code / Error code ("h" shows hexadecimal) (1) ACK reply : 06h When the projector receives the Set, Increment, Decrement or Execute command correctly, the projector changes the setting data for the specied item by [Type], and it returns the code. (2) NAK reply : 15h When the projector cannot understand the received command, the projector returns the error code. In such a case, check the sending code and send the same command again.
Command Control via the Network Command Control via the Network When the projector connects network, the projector can be controlled with RS232C commands from the computer with web browser. For details of RS-232C commands, refer to RS-232C Communication / Network command table ( 17). NOTE • If data is transferred via wireless and wired LAN at the same time, the projector may not be able to process the data correctly. Connection 1. Turn off the projector and the computer.
Command Control via the Network (continued) Communication Port The following two ports are assigned for the command control. TCP #23 TCP #9715 Congure the following items form a web browser when command control is used. Port Settings Port open Click the [Enable] check box to open [Network Control Port1 (Port: 23)] to use TCP #23. Default setting is “Enable”. Authentication Click the [Enable] check box for the [Authentication] setting when authentication is required. Default setting is “Disable”.
Command Control via the Network (continued) Command control settings [TCP #23] 1. Command format Same as RS-232C communication, refer to RS-232C Communicaton command format. 2. Response code / Error code ("h" shows hexadecimal) Four of the response / error code used for TCP#23 are the same as RS-232C Communication (1)~(4). One authentication error reply (5) is added. (1) ACK reply : 06h Refer to RS-232C communication ( 10). (2) NAK reply : 15h Refer to RS-232C communication ( 10).
Command Control via the Network (continued) 2. Response code / Error code ("h" shows hexadecimal) The connection ID is attached for the TCP#23's response / error codes are used. The connection ID is same as the sending command format.
Network Bridge Communication Network Bridge Communication This projector is equipped with NETWORK BRIDGE function. When the projector connects to the computer by wired or wireles LAN communicaton, an external device that is connected with this projector by RS232C communication can be controlled from the computer as a network terminal. For details, see the 6. Network Bridge function in the Network Guide.
Network Bridge Communication (continued) Communication settings For communication setting, use the OPTION - SERVICE - COMMUNICATION menu.
RS-232C Communication / Network command table RS-232C Communication / Network command table Names Operation Type Set Turn off Turn on Power Get Set Input Source Error Status Get MAGNIFY FREEZE COMPUTER IN1 COMPUTER IN2 HDMI S-VIDEO VIDEO LAN USB TYPE A USB TYPE B Get Set Set PICTURE MODE Get Increment Decrement NORMAL FREEZE Get NORMAL CINEMA DYNAMIC BOARD(BLACK) BOARD(GREEN) WHITEBOARD DAYTIME Get BRIGHTNESS BRIGHTNESS Reset CONTRAST CONTRAST Reset Get Increment Decrement Execute Get Incr
RS-232C Communication / Network command table (continued) Names GAMMA User Gamma Pattern User Gamma Point 1 User Gamma Point 1 Reset User Gamma Point 2 User Gamma Point 2 Reset User Gamma Point 3 User Gamma Point 3 Reset User Gamma Point 4 User Gamma Point 4 Reset User Gamma Point 5 User Gamma Point 5 Reset User Gamma Point 6 User Gamma Point 6 Reset User Gamma Point 7 User Gamma Point 7 Reset Operation Type Set Set DEFAULT-1 CUSTOM-1 DEFAULT-2 CUSTOM-2 DEFAULT-3 CUSTOM-3 DEFAULT-4 CUSTOM-4 DEFAULT-5
RS-232C Communication / Network command table (continued) Names Operation Type User Gamma Point 8 User Gamma Point 8 Reset COLOR TEMP Set COLOR TEMP GAIN R Get Increment Decrement Execute 1 HIGH 1 CUSTOM 2 MID 2 CUSTOM 3 LOW 3 CUSTOM 4 Hi-BRIGHT-1 4 CUSTOM 5 Hi-BRIGHT-2 5 CUSTOM 6 Hi-BRIGHT-3 6 CUSTOM Get Get Increment Decrement Header BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE CRC EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF 03 03 03 03 03 03 03 03 03 03 03 03 03 0
RS-232C Communication / Network command table (continued) Names Operation Type COLOR COLOR Reset TINT TINT Reset SHARPNESS SHARPNESS Reset MY MEMORY Load Set MY MEMORY Save Set ASPECT Set OVER SCAN OVER SCAN Reset V POSITION V POSITION Reset H POSITION H POSITION Reset H PHASE (*) only for CPWX12WN (continued on next page) 20 Get Increment Decrement Execute Get Increment Decrement Execute Get Increment Decrement Execute 1 2 3 4 1 2 3 4 4:3 16:9 14:9 16:10 (*) NATIVE NORMAL Get Get Increment Decr
RS-232C Communication / Network command table (continued) Names Operation Type Get Increment Decrement Execute H SIZE H SIZE Reset AUTO ADJUST EXECUTE PROGRESSIVE VIDEO NR COLOR SPACE S-VIDEO FORMAT C-VIDEO FORMAT HDMI FORMAT HDMI RANGE COMPUTER IN1 Execute Set Set Set Set Set Set Set Set OFF TV FILM Get LOW MID HIGH Get AUTO RGB SMPTE240 REC709 REC601 Get AUTO NTSC PAL SECAM NTSC4.43 M-PAL N-PAL Get AUTO NTSC PAL SECAM NTSC4.
RS-232C Communication / Network command table (continued) Names COMPUTER IN2 Operation Type Set FRAME LOCK – COMPUTER IN1 Set FRAME LOCK – COMPUTER IN2 Set FRAME LOCK – HDMI Set AUTO SYNC ON G OFF Get OFF ON Get OFF ON Get OFF ON Get AUTO KEYSTONE EXECUTE Execute KEYSTONE V KEYSTONE V Reset AUTO ECO MODE ECO MODE INSTALLATION STANDBY MODE Set Set Set Set MONITOR OUT COMPUTER IN1 Set MONITOR OUT COMPUTER IN2 Set MONITOR OUT S-VIDEO Set MONITOR OUT VIDEO Set Get Increment Decremen
RS-232C Communication / Network command table (continued) Names Operation Type MONITOR OUT HDMI Set MONITOR OUT - LAN Set MONITOR OUT - USB TYPE A Set MONITOR OUT - USB TYPE B Set MONITOR OUT STANDBY Set VOLUME COMPUTER IN1 VOLUME COMPUTER IN2 VOLUME - S-VIDEO VOLUME - VIDEO VOLUME - HDMI VOLUME - LAN VOLUME - USB TYPE A VOLUME - USB TYPE B VOLUME AUDIO OUT STANDBY COMPUTER IN1 COMPUTER IN2 OFF Get COMPUTER IN1 COMPUTER IN2 OFF Get COMPUTER IN1 COMPUTER IN2 OFF Get COMPUTER IN1 COMPUTER IN
RS-232C Communication / Network command table (continued) Names MUTE SPEAKER Operation Type Set Set AUDIO SOURCE COMPUTER IN1 Set AUDIO SOURCE COMPUTER IN2 Set AUDIO SOURCE HDMI Set AUDIO SOURCE S-VIDEO Set AUDIO SOURCE VIDEO Set AUDIO SOURCE LAN Set AUDIO SOURCE USB TYPE A Set AUDIO SOURCE USB TYPE B Set Set AUDIO SOURCE AUDIO OUT STANDBY LAN SOUND ENABLE Set OFF ON Get ON OFF Get AUDIO IN1 AUDIO IN2 OFF Get AUDIO IN1 AUDIO IN2 OFF Get OFF AUDIO IN1 AUDIO IN2 AUDIO_HDMI Get AUDIO I
RS-232C Communication / Network command table (continued) Names USB TYPE B SOUND ENABLE HDMI AUDIO LANGUAGE * MENU POSITION H Operation Type Disable Enable Get 1 2 Get ENGLISH FRANÇAIS DEUTSCH ESPAÑOL ITALIANO NORSK NEDERLANDS PORTUGUÊS Set Set Set SVENSKA 3ɍ&&.ɂɃ SUOMI POLSKI TÜRKÇE DANSK ý(6.
RS-232C Communication / Network command table (continued) Names Operation Type MENU POSITION V Get Increment Decrement MENU POSITION V Reset Execute BLANK BLANK On/Off START UP MyScreen Lock MESSAGE TEMPLATE TEMPLATE On/Off C. C. - DISPLAY C. C. - MODE C. C.
RS-232C Communication / Network command table (continued) Names AUTO SEARCH AUTO KEYSTONE DIRECT POWER ON Operation Type Set Set Set AUTO POWER OFF USB TYPE B Set LAMP TIME LAMP TIME Reset FILTER TIME FILTER TIME Reset MY BUTTON-1 Set OFF ON Get OFF ON Get OFF ON Get Get Increment Decrement MOUSE USB DISPLAY Get Get Execute Get Execute COMPUTER IN1 COMPUTER IN2 HDMI S-VIDEO VIDEO LAN USB TYPE A USB TYPE B INFORMATION AUTO KEYSTONE MY MEMORY PICTURE MODE FILTER RESET AV MUTE TEMPLATE RESOLUTION
RS-232C Communication / Network command table (continued) Names MY BUTTON-2 MY BUTTON-ECO Operation Type Set Set COMPUTER IN1 COMPUTER IN2 HDMI S-VIDEO VIDEO LAN USB TYPE A USB TYPE B INFORMATION AUTO KEYSTONE MY MEMORY PICTURE MODE FILTER RESET AV MUTE TEMPLATE RESOLUTION ECO MODE MY IMAGE SLIDESHOW MESSENGER Get COMPUTER IN1 COMPUTER IN2 HDMI S-VIDEO VIDEO LAN USB TYPE A USB TYPE B INFORMATION AUTO KEYSTONE MY MEMORY PICTURE MODE FILTER RESET AV MUTE TEMPLATE RESOLUTION ECO MODE MY IMAGE SLIDESHOW M
RS-232C Communication / Network command table (continued) Names MY SOURCE Operation Type Set Magnify Position H Magnify Position V MY IMAGE MY IMAGE IMAGE-1 Delete MY IMAGE IMAGE-2 Delete MY IMAGE IMAGE-3 Delete MY IMAGE IMAGE-4 Delete VOLUME - ALL Set COMPUTER IN1 COMPUTER IN2 HDMI S-VIDEO VIDEO LAN USB TYPE A USB TYPE B Get Get Increment Decrement Get Increment Decrement OFF IMAGE-1 IMAGE-2 IMAGE-3 IMAGE-4 Get Header CRC Action Command Data Type Setting Code BE EF BE EF BE EF BE EF BE EF BE
PJLink command PJLink command Commands Control Description POWR Power Contorol POWR ? Power Status inquiry INPT Input Source selection INPT ? Input Source inquiry AVMT AV Mute AVMT ? AV Mute inquiry (continued on next page) 30 Parameter or Response 0 = Standby 1 = Power On 0 = Standby 1 = Power On 2 = Cool Down 11 = COMPUTER IN 1 12 = COMPUTER IN 2 22 = S-VIDEO 23 = VIDEO 31 = HDMI 41 = USB TYPE A 51 = LAN 52 = USB TYPE B 11 = COMPUTER IN 1 12 = COMPUTER IN 2 22 = S-VIDEO 23 = VIDEO 31 = HD
PJLink command (continued) Commands ERST ? Control Description Error Status inquiry LAMP ? Lamp Status inquiry INST ? Input Source List inquiry NAME ? Projector Name inquiry INF1 ? Manufucturer's Name inquiry INF2 ? INFO ? CLSS ? Parameter or Response 1st byte: Refers to Fan error; one of 0 to 2 2nd byte: Refers to Lamp error; one of 0 to 2 3rd byte: Refers to Temptrature error; one of 0 to 2 4th byte: Refers to Cover error; one of 0 to 2 5th byte: Refers to Filter error; one of 0 to 2 6th byt
Projector User's Manual (concise) Thank you for purchasing this projector. Please read through this manual before using this product, in order to use safely and utilize well the product. WARNING ►Before using this product, be sure to read all manuals for this product. After reading them, store them in a safe place for future reference. ►Heed all the warnings and cautions in the manuals or on the product. ►Follow all the instructions in the manuals or on the product.
First of all Entries and graphical symbols explanation The following entries and graphical symbols are used for the manuals and the product as follows, for safety purpose. Please know their meanings beforehand, and heed them. WARNING This entry warns of a risk of serious personal injury or even death. CAUTION This entry warns of a risk of personal injury or physical damage. NOTICE This entry notices of fear of causing trouble.
Regulatory notices In the US, and other places where the FCC regulations are applicable Declaration of Conformity Trade name HITACHI Model Number CPX10WN, CPX11WN, CPWX12WN Responsible Party Hitachi America, Ltd. Address 900 Hitachi way, Chula Vista, CA 91914-3556 U.S.A. Telephone Number +1 -800-225-1741 This device complies with part 15 of the FCC Rules.
Regulatory notices (continued) About Waste Electrical and Electronic Equipment The mark is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE). The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries or accumulators as unsorted municipal waste, but use the return and collection systems available.
Please insert the batteries into the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a safe place. 1 2 3 Holding the hook part of the battery 1. cover, remove it. and insert the two AA batteries 2. Align (HITACHI MAXELL or HITACHI MAXELL 3. ENERGY, Part No.
Arrangement Refer to table T-1 or T-2 and gures F-1 and F-2 at the end of this manual to determine the screen size and projection distance (from the projector’s end). The values shown in the table are calculated for a full size screen. a Screen size (diagonal) b Projection distance (±10%, from the projector's end) c1 , c2 Screen height (±10%) • If the projector is used at an altitude of about 1600 m (5250 feet) or higher, set ALTITUDE of the SERVICE item in the OPTION menu to HIGH.
Before connecting the projector to a device, consult the manual of the device to conrm that the device is suitable for connecting with this projector and prepare the required accessories, such as a cable in accord with the signal of the device. Consult your dealer when the required accessory did not come with the product or the accessory is damaged. After making sure that the projector and the devices are turned off, perform the connection, according to the following instructions.
Fastening the adapter cover Use the supplied adapter cover to prevent the USB wireless adapter from coming off easily. the screw (marked with triangle) 1. Loosen on the bottom right of the USB TYPE A 1 port. the tab of the cover into the hole 2. Insert at the upper left of the USB TYPE A port in the direction of the arrow. Align the screw holes on the projector and the cover. Then insert the screw removed from the projector into the hole and tighten the screw. 3 2 3.
Turning on the power cover. Press the STANDBY/ON button on the projector or the remote control. The projection lamp will light up and the POWER indicator will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in steady green. ENGLISH Make sure that the power cord is rmly and correctly connected to the 1. projector and the outlet. STANDBY/ON button sure that the POWER indicator is 2. Make POWER indicator steady orange. Then remove the lens 3.
Adjusting the projector's elevator When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally. 12° Using the feet can also tilt the projector in order to project at a suitable angle to the screen, elevating the front side of the projector within 12 degrees. This projector has 2 elevator feet and 2 elevator knobs. An elevator foot is adjustable while pulling up the elevator knob on the same side as it.
Displaying the picture Activate your signal source. Turn the signal source on, and make it send the signal to the projector. Press the INPUT button on the projector. Each time you press the button, the projector switches its input port in turn. You can also use the remote control to select an input signal.
Turning off the power the STANDBY/ON button on the 1. Press projector or the remote control. STANDBY/ON button POWER indicator The message “Power off?” will appear on the screen for about 5 seconds. Press the STANDBY/ON button again while the message appears. The projector lamp will go off, and the POWER indicator will begin blinking in orange. Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete.
A lamp has nite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended. To prepare a new lamp, make contact with your dealer and tell the lamp type number. Type number : DT01191 Lamp cover the projector off, and unplug the power cord. 1.
Replacing the lamp (continued) HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE WARNING ►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
Please check and clean the air lter periodically. When the indicators or a message prompts you to clean the air lter, comply with it as soon as possible. The air lter has two kinds of lters inside. Replace the lters when they are damaged or too soiled. To prepare the new lters, make contact with your dealer and tell the following type number. Type number : UX36761 (Filter set) 2 When you replace the lamp, please replace the air lter.
Using the CD manual The other manuals for this product are written into the included CD-ROM titled “User’s Manual (detailed)”. Before using the CD-ROM, please read the following to ensure the proper use. System requirements The system for using the CD-ROM requires the following. OS:Microsoft® Windows®: Windows® XP, Windows Vista®, Windows®7 or later ® OS:Mac OS® 10.2 or later Macintosh : CD-ROM/DVD-ROM drive: Applications: Microsoft® Internet Explorer®6.0 or later Adobe® Acrobat® Reader® 8.
Lamp 6SHFL¿FDWLRQ Liquid crystal projector CPX10WN, CPX11WN: 786,432 pixels (1024 horizontal x 768 vertical) CPWX12WN: 1,024,000 pixels (1280 horizontal x 800 vertical) 215 W UHP Speaker 1W Power supply/ Rated current AC 100-120 V: 3.3 A, AC 220-240 V: 1.6 A Item Product name Liquid Crystal Panel Power consumption Temperature range Size Weight (mass) ENGLISH Specifications AC 100-120 V: 320 W, AC 220-240 V: 310 W 5 ~ 35 °C (Operating) 306 (W) x 77 (H) x 221 (D) mm * Not including protruding parts.
Troubleshooting - Warranty and after-service If an abnormal operation (such as smoke, strange odor or excessive sound) should occur, stop using the projector immediately. Otherwise if a problem occurs with the projector, rst refer to “Troubleshooting” of User’s Manual - Operating Guide and Network Guide, and run through the suggested checks. If this does not resolve the problem, please consult your dealer or service company. They will tell you what warranty condition is applied.
CPX10WN, CPX11WN a Screen size (diagonal) (1024 x 768) (±10%) 4 : 3 screen b c1 Projection distance Screen height min. max. c2 Screen height 16 : 9 screen b c1 Projection distance Screen height min. max. type (inch) m m inch m inch cm inch cm inch m 30 40 50 60 70 80 90 100 120 150 200 250 300 0.8 1.0 1.3 1.5 1.8 2.0 2.3 2.5 3.0 3.8 5.1 6.4 7.6 0.7 1.0 1.3 1.5 1.8 2.0 2.3 2.6 3.1 3.9 5.2 6.5 7.8 29 39 49 60 70 80 90 101 121 152 203 254 305 0.9 1.2 1.5 1.8 2.1 2.5 2.8 3.1 3.7 4.6 6.2 7.
F-1 F-2 ・On a horizontal surface ・Suspended from the ceiling F-3 Computer HDMI USB TYPE A DC5V 0.
F-4 ENGLISH External device Computer Access point USB wireless adapter (optional) HDMI USB TYPE A DC5V 0.5A USB storage device USB TYPE B COMPUTER IN1 COMPUTER IN2 AUDIO IN1 S-VIDEO VIDEO LAN AC IN AUDIO OUT MONITOR OUT AUDIO IN2 CONTROL F-5 HDMI USB TYPE A DC5V 0.
F-6 Speakers (with an amplier) Monitor RGB IN HDMI USB TYPE A DC5V 0.
ENGLISH F-7 221 AC IN 77 83 306 [unit: mm] 23
NOTE • The information in this manual is subject to change without notice. • The manufacturer assumes no responsibility for any errors that may appear in this manual. • The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent. REMARQUE • Les informations contenues dans ce manuel peuvent faire l'objet dechangements sans avertissement préalable.
Hitachi America, Ltd. Hitachi Europe AB Digital Media Division 900 Hitachi way, Chula Vista CA 91914-3556 USA CANADA Tel: +1 -800-225-1741 ► http://www.hitachi-america.us/digitalmedia Frösundaviks Alle 15 169 29 Solna SWEDEN Sweden Tel: +46 8 562 711 00 Finland Tel: +358 10 8503 085 Norway Tel: +47 9847 3898 Denmark Tel: +46 8 562 711 00 ► http://www.hitachidigitalmedia.com Hitachi Europe Ltd.