Model Modèle Modelo Rotary Hammer Marteau rotatif Martillo giratorio DH 25PB SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL WARNING IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury! This manual contains important information about product safety. Please read and understand this manual BEFORE operating the power tool. Please keep this manual available for other users and owners before they use the power tool. This manual should be stored in safe place.
CONTENTS English Page IMPORTANT SAFETY INFORMATION ................ 3 MEANINGS OF SIGNAL WORDS ........................ 3 SAFETY ...................................................................... 4 GENERAL SAFETY RULES ................................... 4 SPECIFIC SAFETY RULES AND SYMBOLS ......... 6 DOUBLE INSULATION FOR SAFER OPERATION ................................................... 8 Page ASSEMBLY AND OPERATION ............................... 10 APPLICATIONS .................................
English IMPORTANT SAFETY INFORMATION Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power tool. Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures.
English SAFETY GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS 1. Work Area (1) Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. (2) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
English (4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. (5) Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. (6) Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. 4.
English SPECIFIC SAFETY RULES AND SYMBOLS 1. Hold tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. 2. ALWAYS wear ear protectors when using the tool for extended periods. Prolonged exposure to high intensity noise can cause hearing loss. 3. NEVER touch the tool bit with bare hands after operation. 4.
English 15. Operate power tools at the rated voltage. Operate the power tool at voltages specified on its nameplate. If using the power tool at a higher voltage than the rated voltage, it will result in abnormally fast motor revolution and may damage the unit and the motor may burn out. 16. NEVER use a tool which is defective or operating abnormally.
English DOUBLE INSULATION FOR SAFER OPERATION To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. “Double insulation “ means that two physically separated insulation systems have been used to insulate the electrically conductive materials connected to the power supply from the outer frame handled by the operator. Therefore, either the symbol “ ” or the words “Double insulation” appear on the power tool or on the nameplate.
English FUNCTIONAL DESCRIPTION NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety instructions contained in this manual. Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own power tool.
English ASSEMBLY AND OPERATION APPLICATIONS Rotation and striking function 䡬 Drilling anchor holes 䡬 Drilling holes in concrete 䡬 Drilling holes in tile Rotation only function 䡬 Drilling in steel or wood (with optional accessories). 䡬 Tightening machine screws, wood screws (with optional accessories). PRIOR TO OPERATION 1. Power source Ensure that the power source to be utilized conforms to the power source requirements specified on the product nameplate. 2.
English 6. Mounting the drill bit (Fig. 2) (1) To attach a drill bit (SDS-plus shank), fully pull the grip in the direction of the arrow as shown in Fig. 2 and insert the drill bit as far as it will go while manually turning. (2) By releasing the grip, the drill bit will be secured. (3) To remove the drill bit, fully pull the grip in the direction of the arrow and pull out the drill bit. Front cap Part of SDS-plus shank Grip Drill bit Fig. 2 7.
English HOW TO USE CAUTION: 䢇 To prevent accidents, make sure to turn the switch off and disconnect the plug from the receptacle when the drill pits and other various parts are installed or removed. The power switch should also be turned off during a work break and after work. Change lever Fig. 5 1. Switch operation The rotation speed of the drill bit can be controlled steplessly by varying the amount that the trigger switch is pulled.
English CAUTION: 䢇 Application of force more than necessary will not only reducing drilling efficiency at all, but will deteriorate the tip edge of the drill bit and reduce the service life of the rotary hammer in addition. 䢇 Drill bit may snap off while disengaging the rotary hammer from the jammed hole. For disengaging, it is important to use a pushing motion or turn the drill bit counterclockwise.
English requiring much power to drive the screw into it, the thread of the wood screw may sometimes be damaged. Mounting hole 6. Using the stopper (Fig. 10) (1) Loosen the knob on the side handle, and insert the stopper into the mounting hole on the side handle. (2) Adjust the stopper position according to the depth of the hole and tighten the knob securely. Stopper Side handle 7. How to use the drill bit (taper shank) and the taper shank adaptor. (1) Mount the taper shank adaptor to the rotary hammer.
English HOW TO USE THE CORE BIT (FOR LIGHT LOAD) When boring penetrating large hole use the core bit (for light load). At that time use with the center pin and the core bit shank provided as optional accessories. 1. Mounting CAUTION: 䢇 Be sure to turn power OFF and disconnect the plug from the receptacle. (1) Mount the core bit to the core bit shank. (Fig. 13) Lubricate the thread of the core bit shank to facilitate disassembly. (2) Mount the core bit shank to the rotary hammer. (Fig.
English CAUTION: 䢇 When removing the center pin and the guide plate, turn OFF the switch and disconnect the plug form the receptacle. 3. Dismounting. (Fig. 17) Remove the core bit shank from the rotary hammer and strike the head of the core bit shank strongly two or three times with the manual hammer holding the core bit, then the thread becomes loose and the core bit can be removed. Core bit shank Fig. 17 16 e01_dh25pb(02_24)e.
English MAINTENANCE AND INSPECTION WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle during maintenance and inspection. 1. Inspecting the drill bits Since use of a dull tool will cause motor malfunctioning and degraded efficiency, replace the drill bit with a new one or resharpening without delay when abrasion is noted. 2. Inspecting the screws Regularly inspect all screws and ensure that they are properly tightened.
English 䡬 Replacing carbon brushes: (For parts name, refer to Fig. 1) Loosen the two set screws and remove the tail cover. Remove the brush caps and carbon brushes. After replacing the carbon brushes, tighten the brush caps securely and to install the tail cover with securely tightening two set screws. 5. How to replase grease This machine is full air-tight construction to protect against dust and to prevent lubricant leakage. Therefore, the machine can be used without lubrication for long periods.
e01_dh25pb(02_24)e.
e01_dh25pb(02_24)e.
e01_dh25pb(02_24)e.
e01_dh25pb(02_24)e.
e01_dh25pb(02_24)e.
e01_dh25pb(02_24)e.
Français INFORMATIONS IMPORTANTES DE SÉCURITÉ Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions de fonctionnement dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé. La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé proviennent d’un non respect des règles ou précautions de base de sécurité.
Français SECURITE REGLES GENERALE DE SECURITE AVERTISSEMENT: Lire et coxmprendre toutes les instructions. Un non respect de toutes les instructions ci-dessous peut entraîner une électrocution, un incendie et/ou de sérieuses blessures personnelles. CONSERVER CES INSTRUCTIONS 1. Zone de travail (1) Garder la zone de travail propre et bien éclairée. Les établis mal rangés et les zones sombres invitent aux accidents.
Français (2) S’habiller correctement. Ne pas porter des vêtements larges ou des bijoux. Attacher les cheveux longs. Tenir ses cheveux, vêtements et ses gants éloignés des parties mobiles. Les vêtements larges, les bijoux et les cheveux longs peuvent se prendre dans les parties mobiles. (3) Eviter tout démarrage accidentel. S’assurer que le l’interrupteur d’alimentation est sur la position d’arrêt avant de brancher la machine.
Français (2) Lors de la réparation d’un outil, utiliser uniquement des pièces de rechange identiques. Suivre les instructions de la section d’entretien de ce mode d’emploi. L’utilisation de pièces non autorisées ou un non respect des instructions d’entretien peut créer un risque d’électrocution ou de blessures. REGLES DE SECURITE SPECIFIQUES ET SYMBOLES 1.
Français 11. Maintenir toutes les vis, tous les boulons et les couvercles fermement en place. Maintenir toutes les vis, tous les boulons et les couvercles fermement montés. Vérifier leurs conditions périodiquement. 12. Ne pas utiliser les outils motorisés si le revêtement de plastique ou la poignée est fendu. Des fentes dans le revêtement ou la poignée peuvent entraîner une électrocution. De tels outils ne doivent pas être utilisés avant d’être réparé. 13.
Français 22. Définitions pour les symboles utilisés sur cet outil V ............ volts Hz .......... hertz A ............ ampères no ........... vitesse sans charge W ........... watt ........... Construction de classe II ---/min ... tours par minute .......... Courant alternatif DOUBLE ISOLATION POUR UN FONCTIONNEMENT PLUS SUR Pour assurer un fonctionnement plus sûr de cet outil motorisé, HITACHI a adopté une conception à double insolation.
Français DESCRIPTION FONCTIONNELLE REMARQUE: Les informations contenues dans ce mode d’emploi sont conçues pour assister l’utilisateur dans une utilisation sans danger et un entretien de l’outil motorisé. NE JAMAIS utiliser ni entreprendre une révision de l’outil sans avoir d’abord lu et compris toutes les instructions de sécurité contenues dans ce manuel. Certaines illustrations dans ce mode d’emploi peuvent montrer des détails ou des accessoires différents de ceux de l’outil motorisé utilisé.
Français ASSEMBLAGE ET FONCTIONNEMENT APPLICATIONS Par action combinée de rotation et de frappe 䡬 Perçage de trous d’ancrage 䡬 Perçage de trous dans béton 䡬 Perçage de trous dans une tuile Par action de rotation uniquement 䡬 Perçage de l’acier ou du bois (avec accessoires en option) 䡬 Serreage de vis mécaniques et de vis à bois. (avec accessoires en option) AVANT L’UTILISATION 1.
Français 6. Montage (Fig. 2) du foret de perçage Capuchon Elément de la avant (1) Pour fixer un foret de perçage (tige SDS plus), tige SDS plus tirer complètement l’attache coulissante dans le sens de la flèche, comme indiqué sur la Fig. 2, puis insérer le foret tout en le faisant tourner Attache jusqu’à ce qu’il atteigne le fond. coulissante Foret de (2) Lorsque l’attache coulissante est relâchée, le perçage foret est fixé. Fig.
Français 6-19/64" (160 mm) ou 4-21/64" (110 mm) de longueur totale. 䢇 Vider les particules dans le collecteur à poussière (B) chaque deux ou trois trous percés. 䢇 Remettre en place le foret après avoir enlevé le collecteur à poussière (B). 8. Sélection de la mèche pour visseuse Les têtes de vis ou les mèches seront endommagées si une mèche inappropriée au diamètre de la vis n’est pas employée pour enfoncer la vis.
Français 3. Rotation seulement Cette perceuse à percussion peut être mise sur le mode de rotation uniquement en tournant le sélecteur à fond dans le sens des aiguilles d’une montre vers le repère . (Fig. 7) Pour percer du bois ou du métal en utilisant le mandrin porte-foret et le raccord de mandrin (accessoire en option), procéder de la manière suivante. Mise en place de mandrin porte-foret et du raccord de mandrin: (Fig. 8) (1) Fixer le mandrin porte-foret sur le raccord.
Français PRECAUTION: 䢇 Faites attention de ne pas prolonger la durée d’enfoncement plus qu’il n’est nécessaire, sinon les vis pourraient être endommagées suite à la force excessive utilisée. 䢇 Appliquez le marteau rotatif perpendiculairement par rapport à la tête de la vis lors de l’enfoncement de la vis; sinon la tête de la vis ou la mèche seront endommagées, ou la force d’entraînement ne sera pas entièrement transférée à la vis.
Français (4) Pour retirer la mèche (queue conique), introduire la clavette dans la fente du raccord de queue conique et frapper la tête de la clavette avec un marteau alors que le perceuse est placée sur le support. (Fig. 12) Clavette Raccord de queue conique 8. Utilisation de la poignée latérale Si l’on désire modifier la position de la poignée latérale, tourner le manche de la poignée latérale dans le sens inverse des aiguilles d’une montre pour desserrer la poignée, puis la fixer solidement.
Français (4) Engager la plaque de guidage dans la couronne et tourner la plaque de guidage à gauche ou à droite de manière à ce qu’elle à ce qu’elle ne puisse pas tomber, même si elle orientée vers le bas. (Fig. 15) Plaque de guidage Goujon central Bout de couronne Couronne 2. Perçage (Fig. 16) (1) Brancher la perceuse. (2) Un ressort est placé dans le goujon central. Appuyer légèrement l’outil perpendiculairement contre le mur ou le plancher.
Français ENTRETIEN ET INSPECTION AVERTISSEMENT: S’assurer de mettre l’interrupteur d’alimentation sur la position OFF et de déconnecter la fiche de la prise secteur avant l’entretien et l’inspection de la meuleuse. 1. Contrôle du foret de perçage Etant donné que l’utilisation d’une mèche usée entraînera un mauvais fonctionnement du moteur et une diminution de l’efficacité, remplacez la mèche usée par une neuve ou aiguisez-la immédiatement et dès que vous notez une certaine usure. 2.
Français 䡬 Remplacement du balais en carbone Desserrer la vis de fixation et enlever le couvercle de la queue. Enlever la chapeau de balai et la balai en carbone. Après avoir remplacé le balai en carbone, serrer fermement le chapeau du balai et installer le couvercle avec deux vis de fixation. 5. Comment remplacer la graisse Cette machine est de contruction entièrement hermétique pour la protéger contre la poussière et pour éviter les fuites de lubrifiant.
f02_dh25pb(25_46)e.
f02_dh25pb(25_46)e.
f02_dh25pb(25_46)e.
f02_dh25pb(25_46)e.
f02_dh25pb(25_46)e.
f02_dh25pb(25_46)e.
Español INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD Antes de utilizar o de realizar cualquier trabajo de mantenimiento de esta herramienta eléctrica, lea y comprenda todas las precauciones de seguridad, advertencias e instrucciones de funcionamiento de este Manual de instrucciones. La mayoría de los accidentes producidos en la operación y el mantenimiento de una herramienta eléctrica se deben a la falta de observación de las normas o precauciones de seguridad.
Español SEGURIDAD NORMAS GENERALES DE SEGURIDAD ADVERTENCIA: Lea y entienda todas las instrucciones. Si no sigue las instrucciones indicadas a continuación, pueden producirse descargas eléctricas, incendios, y/o lesiones serias. GUARDE ESTAS INSTRUCCIONES. 1. Área de trabajo (1) Mantenga el área de trabajo limpia y bien iluminada. Los bancos de trabajo desordenados y las áreas obscuras pueden conducir a accidentes.
Español ni de alcohol. Un descuido al utilizar la herramienta eléctrica puede resultar en una lesión seria. (2) Vístase adecuadamente. No utilice ropa floja ni joyas. Si tiene pelo largo, recójaselo. Mantenga su pelo, ropa, y guantes alejados de las partes móviles. La ropa floja, las joyas, o el pelo largo pueden engancharse en las partes móviles. (3) Evite la puesta en marcha accidental.
Español (2) Para el servicio de mantenimiento o reparación de una herramienta, utilice solamente piezas de repuesto idénticas. Siga las instrucciones de la sección de mantenimiento de este manual. La utilización de piezas no autorizadas, o el no seguir las indicaciones del Manual de instrucciones puede crear el riesgo de descargas eléctricas u otras lesiones. NORMAS Y SÍMBOLOS ESPECÍFICOS DE SEGURIDAD 1.
Español 10. Maneje correctamente la herramienta. Maneje la herramienta de acuerdo con las instrucciones ofrecidas aquí. No deje caer ni tire la herramienta. NO permita NUNCA que los niños ni otras personas no autorizadas ni familiarizadas con la operación de la herramienta utilicen ésta. 11. Mantenga todos los tornillos, pernos, y cubiertas firmemente fijados en su lugar. Mantenga todos los tornillos, pernos, y cubiertas firmemente montados. Compruebe periódicamente su condición. 12.
Español 21. Tenga cuidado SIEMPRE con los objetos que puedan estar enterrados o emparedados, tales como cables eléctricos. Si tocase un cable activo con esta herramienta, podría recibir una descarga eléctrica. Confirme que no haya ningún objeto enterrado o emparedado, como cables electricos, en el suelo, el techo, o en las paredes en los que vaya a trabajar. 22. Definiciones para los símbolos utilizados en esta herramienta V ................. voltios Hz ............... hertzios A .................
Español ¡GUARDE ESTAS INSTRUCCIONES Y PÓNGALAS A DISPOSICIÓN DE OTROS USUARIOS Y PROPIETARIOS DE ESTA HERRAMIENTA! 53 sp03_dh25pb(47_71)e.
Español DESCRIPCIÓN FUNCIONAL NOTA: La información contenida en este Manual de instrucciones ha sido diseñada para ayudarle a utilizar con seguridad y mantener esta herramienta eléctrica. NUNCA haga funcionar ni efectúe el mantenimiento de la herramienta antes de leer y comprender todas las instrucciones de seguridad contenidas en este manual. Algunas ilustraciones de este Manual de Instrucciones pueden mostrar detalles o accesorios diferentes a los de la propia herramienta eléctrica.
Español MONTAJE Y OPERACIÓN APLICACIONES Acción combinada de rotación y golpeteo 䡬 Perforación de orificios de anclaje 䡬 Perforación de orificios de hormigón 䡬 Perforación de orificios de baldosa Rotación solamente 䡬 Perforación de orificios en hormigón o madera (con accesorios facultativos) 䡬 Apretar tornillos en metal o madera. (con accesorios facultativos) ANTES DE LA OPERACIÓN 1.
Español 6. Montaje de la broca (Fig. 2) Cubierta (1) Para colocar una broca (SDS más vástago), Parte del SDS frontal más vástago tire completamente de la empuñadura en el sentido de la flecha como se muestra en la Fig. 2 en inserte profundamente la froca girándola. Sujetador (2) Al soltar la empuñadura, la broca quadará Broca asegurada. (3) Para extraer la broca, tire completamente de Fig. 2 la empuñadura en el sentido de la flecha y tire hacia afuera de la broca. 7.
Español 8. Selección de la broca destornillador Las cabezas de tornillos y las brocas de atornillar se dañarán menos que se emplee la broca apropiada según sea el diámetro del tornillo. COMO SE USA PRECAUCIÓN: 䢇 Para evitar accidentes, cerciórese de poner este interruptor en OFF y de desconectar el enchufe del tomacorriente cuando instale o extraiga brocas y otras piezas.
Español 3. Rotación solamente Este martillo roto-percutor puede ajustarse al modo de rotación solamente girando completamente la palanca selectora en sentido contrario a las agujas del reloj, hasta la marca (Fig.7). Para perforar madera o metal empleando el portabrocas y el adaptador del portabrocas (accesorio facultativo), proceder como sigue. Instalación del portabrocas y adaptador del portabrocas: (Fig. 8) (1) Instale la broca en el adaptador del portabrocas.
Español PRECAUCIÓN: 䢇 Tener cuidado en no prolongar excesivamente el accionamiento de la herramienta, ya que de lo contrario, pueden dañarse los tornillos por el exceso de fuerza. 䢇 Colocar el martillo giratorio en forma perpendicular sobre la cabeza del tornillo al atornillarlo, ya que en caso contrario, puede dañarse la cabeza del tornillo o la broca, e incluso, la fuerza de accionamiento puede que no se transfiera por completo al tornillo.
Español 7. Modo de usar la broca (espiga ahusada) y el adaptador de la espiga ahusada Cubierta frontal (1) Montar el adaptador de la espiga ahusada en Broca el martillo giratorio (Fig. 11). (2) Montar la broca (espiga ahusada) en el adaptador de la espiga ahusada (Fig. 11) Adaptador de la (3) Poner el interruptor en la posición de espiga ahusada encendido (ON), y taladrar un agujero de la profundidad especificada.
Español (1) Montar la barrena tubular en su espiga. (Fig. 13) Lubricar la rosca de la espiga de la barrena tubular para facilitar el desmontaje. (2) Montar la espiga de la barrena tubular en el martillo giratorío. (Fig. 14) Barrena tubular Rosca Espiga de la barrena tubular Fig. 13 Fig. 14 (3) Insertar el pasador central en la placa guía hasta que se pare.
Español 3. Desmontaje (Fig. 17) Como otro método, quitar la espiga de la barrena tubular del martillo giratorio y golpear fuertemente la cabeza de la espiga de la barrena tubular dos o tres veces con un martillo sujetanto la punta de la barrena. La parte roscada se aflojará y la barrena tubular podrá quitarse. Espiga de la barrena tubular Fig. 17 62 sp03_dh25pb(47_71)e.
Español MANTENIMIENTO E INSPECCIÓN ADVERTENCIA: Antes de realizar el mantenimiento o la inspección de la amoladora, cerciórese de desconectar la alimentación y de desenchufar el cable de alimentación del tomacorriente. 1. Inspeccionar la broca de taladro Debido a que el uso de brocs desafiladas pueden causar mal funcionamiento del motor y desmejorar la eficacia del taladro, hay que reemplazar las brocas en malas condiciones por nuevas o afilarlas de inmediato al advertir abrasión. 2.
Español 䡬 Cambio de escobillas de carbón: Quitar la cubierta de cola y luego aflojar el tornillo de fijación. Aflojando la tapa de escobilla, pueden quitarse las escobillas de carbón, al colocar las escobillas, apretar firmemente la tapa de escobillas y recolocar la cubierta de con dos tornillos. 5. Cambio de grasa Esta máquina es de construcción completamente cerrada, para evitar que entre polvo y haya fugas de lubricante. Por ello, la herramienta puede usarse sin lubricarse por largos periodos.
sp03_dh25pb(47_71)e.
sp03_dh25pb(47_71)e.
sp03_dh25pb(47_71)e.
sp03_dh25pb(47_71)e.
sp03_dh25pb(47_71)e.
sp03_dh25pb(47_71)e.
sp03_dh25pb(47_71)e.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● Lead from lead-based paints, ● Crystalline silica from bricks and cement and other masonry products, and ● Arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.