Model Modèle Modelo DS 14DSAL • DS 18DSAL Cordless Driver Drill Perceuse-visseuse sans fil Taladro atornillador a batería DS18DSAL SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL WARNING IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury! This manual contains important information about product safety. Please read and understand this manual BEFORE operating the power tool. Please keep this manual available for other users and owners before they use the power tool.
CONTENTS English Page IMPORTANT SAFETY INSTRUCTIONS ............... 3 MEANINGS OF SIGNAL WORDS ........................ 3 SAFETY ...................................................................... 3 GENERAL POWER TOOL SAFETY WARNINGS ... 3 SPECIFIC SAFETY RULES AND SYMBOLS ......... 5 IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGER ...................................... 6 IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE BATTERY AND BATTERY CHARGER ......................................
English IMPORTANT SAFETY INSTRUCTIONS Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power tool. Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures.
English 4) A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, nonskid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool.
English WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known [to the State of California] to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● Lead from lead-based paints, ● Crystalline silica from bricks and cement and other masonry products, and ● Arsenic and chromium from chemically-treated lumber.
English CAUTION: 1 Do not place the tool on a workbench or work area where metal chips are present. The chips may adhere to the tool, resulting in injury or malfunction. 2 If chips have adhered to the tool, do not touch it. Remove the chips with a brush. Failure to do so may result in injury. IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGER WARNING: Death or serious bodily injury could result from improper or unsafe use of battery chargers.
English * If the input rating of a battery charger is given in watts rather than in amperes, the corresponding ampere rating is to be determined by dividing the wattage rating by the voltage rating–for example: 1,250 watts = 10 amperes 125 volts Do not operate battery charger with damaged cord or plug-replace them immediately. 10. Do not operate battery charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. 11.
English 3. Do not use an apparently damaged or deformed battery. 4. Do not use the battery in reverse polarity. 5. Do not connect directly to an electrical outlets or car cigarette lighter sockets. 6. Do not use the battery for a purpose other than those specified. 7. If the battery charging fails to complete even when a specified recharging time has elapsed, immediately stop further recharging. 8.
English FUNCTIONAL DESCRIPTION NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety instructions contained in this manual. Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own power tool. NAME OF PARTS 1.
English 2. Battery Charger (UC18YGSL) Guide rail Pilot lamp Nameplate Fig. 2 SPECIFICATIONS 1. Cordless Driver Drill Model Motor No-load speed Capacity Drilling Screw Driver DS14DSAL DC motor Low High Wood (Thickness 11/16" (18 mm)) Metal (Thickness 1/16" (1.6 mm)) Wood screw Small screw Drill chuck capacity Battery Model Type Voltage Weight (without hook) 2.
English ASSEMBLY AND OPERATION WARNING: Do not charge at voltage higher than indicated on the nameplate. If charged at voltage higher than indicated on the nameplate, the charger will burn up. APPLICATIONS 䡬 䡬 Use as a drill Drilling of soft steel, wood, plastic and aluminum materials. Use as a screwdriver Tightening and loosening of machine screws, wood screws and tapping screws. 1. REMOVAL AND INSTALLATION METHOD OF BATTERY 1. 2. WARNING: Do not use the electrical cord if damaged.
English (1) Pilot lamp indication The indications of the pilot lamp will be as shown in Table 2, according to the condition of the charger or the rechargeable battery. Table 2 Indications of the pilot lamp Pilot lamp (red) Before charging Blinks Lights for 0.5 seconds. Does not light for 0.5 seconds. (off for 0.5 seconds) While charging Lights Lights continuously Charging complete Blinks Lights for 0.5 seconds. Does not light for 0.5 seconds. (off for 0.
English ● Since the built-in micro computer takes about 3 seconds to confirm that the battery being charged with UC18YGSL is taken out, wait for a minimum of 3 seconds before reinserting it to continue charging. If the battery is reinserted within 3 seconds, the battery may not be properly charged. BEFORE USE Check the work area to make sure that it is clear of debris and clutter. Clear the area of unnecessary personnel. Ensure that lighting and ventilation is adequate.
English 6. Tightening torque adjustment (1) Tightening torque Tightening torque should correspond in its intensity to the screw diameter. When too strong torque is used, the screw head may be broken or be injured. Be sure to adjust the clutch dial position according to the screw diameter. (2) Tightening torque indication (See Fig. 6) The tightening torque differs depending on the type of screw and the material being tightened. The unit indicates the tightening torque with the numbers “1, 3, 5 ...
English 䢇 䢇 When carrying the power tool with hooked to your waist belt, do not fit any bit to the tip of power tool. If the sharp bit such as drill is fitted to the power tool when carrying it with hooked to your waist belt, you will be injured. Install securely the hook. Unless the hook is securely installed, it may cause an injury while using. 11. Using the light Pull the trigger switch to light up the light. The light keeps on lighting while the trigger switch is being pulled.
English 13. How to select tightening torque and rotational speed 䢇 CAUTION The selection examples shown in Table 6 should be considered as general standard. As different types of tightening screws and different materials to be tightened are used in actual works proper adjustments are naturally necessary.
English MAINTENANCE AND INSPECTION 䢇 1. 䢇 2. 䢇 3. 4. Nail of carbon brush Protrusion of carbon brush CAUTION Pull out battery before doing any inspection or maintenance. Checking the condition of the bit The bits should be checked regularly. If worn or broken bits can slip or decrease the efficiency of the motor and burn it out. Replace worn bits with new ones. CAUTION If you use a driver bit of which point is worn or broken, it will be dangerous since it slips. So replace it with a new one. Fig.
English 6. 7. Check for Dust Dust may be removed with a soft cloth or a cloth dampened with soapy water. Do not use bleach, chlorine, gasoline or thinner, for they may damage the plastics. Disposal of the exhausted battery WARNING: Do not dispose of the exhausted battery. The battery must explode if it is incinerated. The product that you have purchased contains a rechargeable battery. The battery is recyclable.
English ACCESSORIES WARNING: ALWAYS use Only authorized HITACHI replacement parts and accessories. NEVER use replacement parts or accessories which are not intended for use with this tool. Contact HITACHI if you are not sure whether it is safe to use a particular replacement part or accessory with your tool. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage. NOTE: Accessories are subject to change without any obligation on the part of the HITACHI.
English OPTIONAL ACCESSORIES.....sold separately 1. Battery BSL1415X (Code No. 330140) BSL1815X (Code No.
Français CONSIGNES DE SÉCURITÉ IMPORTANTES Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions de fonctionnement dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé. La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé proviennent d’un non respect des règles ou précautions de base de sécurité.
Français e) 3) En cas d'utilisation d'un outil électrique à l'extérieur, utiliser un cordon de rallonge adapté à un usage extérieur. L'utilisation d'un cordon adapté à l'usage extérieur réduit les risques de choc électrique. f) Si vous devez utiliser un outil électrique dans un endroit humide, utilisez une alimentation protégée contre les courants résiduels. L'utilisation d'un dispositif de protection contre les courants résiduels réduit le risque de choc électrique.
Français c) 6) Lorsque la batterie est inutilisée, la garder à l’écart d’objets métalliques comme des trombones, des pièces de monnaie, des clés, des clous, des vis ou autres petits objets métalliques pouvant raccorder les bornes. La connexion des bornes peut entraîner des blessures ou un incendie. d) En cas d’utilisation dans des conditions extrêmes, du liquide peut être émis de la batterie. Éviter tout contact. en cas de contact accidentel, rincer à l’eau.
Français 14. Les lames et les accessoires doivent être fermement montés sur l’outil. Eviter les blessures potentielles personnelles et aux autres. Les lames, les instruments de coupe et les accessoires qui ont été montés sur l’outil doivent être fixés et serrés fermement. 15. NE JAMAIS utiliser un outil défectueux ou qui fonctionne anormalement.
Français a. b. Les broches de la rallonge ont les mêmes numéro, taille et forme que celles de la fiche du chargeur ; Le cordon de rallonge est correctement raccordé et en bon état électrique ; c. Le calibre du fil doit être au moins suffisant pour l’intensité nominale CA (ampères) du chargeur de batterie spécifiées dans le tableau ci-dessous.
Français 12. TOUJOURS alimenter le chargeur sur une prise secteur domestique standard (120 volts). L’utilisation du chargeur à une autre tension peut entraîner une surchauffe et endommager le chargeur. 13. TOUJOURS attendre au moins 15 minutes entre deux recharges pour éviter toute surchauffe du chargeur. 14. TOUJOURS débrancher le cordon d’alimentation de la prise secteur lorsqu’on ne se sert pas du chargeur.
Français 䡬 Soit ranger le bloc de pile avec l’outil électrique ou de manière sécuritaire en l’enfonçant dans le couvercle jusqu’à ce que les orifices de ventilation soient dissimulés afin d’éviter les courts-circuits. (Voir la Fig.
Français DESCRIPTION FONCTIONNELLE REMARQUE: Les informations contenues dans ce mode d’emploi sont conçues pour assister l’utilisateur dans une utilisation sans danger et un entretien de l’outil motorisé. NE JAMAIS utiliser ni entreprendre une révision de l’outil sans avoir d’abord lu et compris toutes les instructions de sécurité contenues dans ce manuel. Certaines illustrations dans ce mode d’emploi peuvent montrer des détails ou des accessoires différents de ceux de l’outil motorisé utilisé.
Français 2. Chargeur de batterie (UC18YGSL) Rail guide Lampe témoin Plaque signalétique Fig. 2 SPECIFICATIONS 1. Perceuse-visseuse à batterie Modèle Moteur Vitesse à vide Capacité DS14DSAL Perçage Vissage Faible Elevée Bois (Epaisseur 11/16" (18 mm)) Métal (Epaisseur 1/16" (1.6 mm)) Vis en bois Petite vis Capacité de mandrin Batterie Modèle Type Tension Poids (sans crochet) 2.
Français ASSEMBLAGE ET FONCTIONNEMENT AVERTISSEMENT: Ne pas effectuer de recharge à une tension supérieure à la tension indiquée sur la plaque signalétique. Cela brûlerait le chargeur. UTILISATIONS 䡬 䡬 Utilisation comme mèche Perçage d’acier doux, de bois, de plastique et d’aluminium. Utilisation comme tournevis Serrage et desserrage de vis à métaux, vis en bois et vis auto-taraudeuses. 1. MÉTHODE DE RETRAIT ET D’INSTALLATION DE LA BATTERIE 1. 2.
Français 3. Recharge Quand la batterie est raccordée au chargeur de batterie, la recharge commence et la lampe témoin s’allume en rouge. (Voir le Tableau 2) REMARQUE: Si la lampe témoin clignote en rouge, débrancher la fiche de la prise et vérifier si la batterie est insérée correctement. Quand la batterie est rechargée à fond, la lampe témoin clignote lentement en rouge.
Français (2) Eviter d’effectuer la recharge sous des températures élevées. Une batterie est toujours chaude immédiatement après son utilisation. Si la batterie est rechargée immédiatement après utilisation, les substances chimiques internes risquent de se détériorer et la durée de vie de la batterie se raccourcira. Laisser la batterie refroidir un moment avant de l’utiliser. ● ● ● ATTENTION : Si le chargeur a fonctionné pendant longtemps de suite, il sera chaud, ce qui risque de provoquer des pannes.
Français (1) En mode visseuse, alignez l’un des chiffres du sélecteur “1, 3, 5, ... 22” ou le point avec le repère triangulaire sur le corps. (2) En mode perceuse, alignez le symbole du foret “ ” sur le sélecteur de débrayage avec le repère triangulaire sur le corps. ● ATTENTION : Il est impossible de positionner le sélecteur de débrayage entre les nombres “1, 3, 5, ... 22” ou le point.
Français Vitesse élevée Bouton de décalage Vitesse ralentie (2) Remplacer le crochet et serrer les vis. Installez le crochet à fond dans la gorge de l’outil électrique et serrez les vis pour le maintenir fermement. (Fig. 11) Bouton de décalage Fig. 9 9. 䡬 䡬 Fonctionnement de l’interrupteur Quand on tire sur la gâchette de l’interrupteur, l’outil tourne. Quand on relâche la gâchette, l’outil s’arrête.
Français Tableau 5 Travail Position du sélecteur de débrayage Suggestions Bois Perçage Acier Utilisation à des fins de perçage. Aluminium Petite vis 1 – 22 Utiliser la mèche et la douille correspondant au diamètre de la vis. Vis en bois 1– Utiliser après avoir percé un trou d’amorce. Vissage 13.
Français ENTRETIEN ET INSPECTION ● 1. ATTENTION: Sortir la batterie avant toute opération d’inspection ou d’entretien. Clou de balai en carbone Saillie de balai en carbone Vérifier l’état de la mèche Les mèches doivent être vérifiées régulièrement. Si elles sont usées ou cassées, elles risquent de glisser ou de réduire le rendement du moteur et de le brûler. Remplacer les mèches usées par des neuves. Fig. 14 ● 2. ● 3. 4.
Français 6. 7. Vérifier s’il y a de la poussière Enlever la poussière avec un chiffon doux ou un chiffon humecté d’eau savonneuse. Ne pas utiliser de décolorant, chlorure, essence ou diluant, car ces produits pourraient endommager le plastique. Mise au rebut d’une batterie usée AVERTISSEMENT: Ne pas jeter la batterie usée aux ordures ménagères. La batterie risque d’exploser si elle est incinérée. L’appareil que vous avez acheté renferme une batterie rechargeable. La batterie est recyclable.
Français ACCESSOIRES AVERTISSEMENT: TOUJOURS utiliser UNIQUEMENT des pièces de rechange et des accessoires HITACHI. NE JAMAIS utiliser de pièce de rechange ou d’accessoires qui ne sont pas prévus pour être utilisé avec cet outil. En cas de doute, contacter HITACHI pour savoir si une pièce de rechange ou un accessoire particulier peuvent être utilisés en toute sécurité avec votre outil.
Français ACCESSOIRES EN OPTION.....vendus séparément 1.
Español INSTRUCCIONES IMPORTANTES SOBRE SEGURIDAD Antes de utilizar o de realizar cualquier trabajo de mantenimiento de esta herramienta eléctrica, lea y comprenda todas las precauciones de seguridad, advertencias e instrucciones de funcionamiento de este Manual de instrucciones. La mayoría de los accidentes producidos en la operación y el mantenimiento de una herramienta eléctrica se deben a la falta de observación de las normas o precauciones de seguridad.
Español 3) Mantenga el cable alejado del calor, del aceite, de bordes afilados o piezas móviles. Los cables dañados o enredados aumentan el riesgo de descarga eléctrica. e) Cuando utilice una herramienta eléctrica al aire libre, utilice un cable prolongador adecuado para utilizarse al aire libre. La utilización de un cable adecuado para usarse al aire libre reduce el riesgo de descarga eléctrica.
Español b) 6) Utilice herramientas eléctricas sólo con paquetes de pilas específicamente diseñados. La utilización de otros paquetes de pilas podría crear riesgo de daños e incendio. c) Cuando no se utilice el paquete de pilas, manténgalo alejado de otros objetos metálicos como clips, monedas, llaves, clavos, tornillos u otros objetos metálicos pequeños que puedan hacer una conexión de un terminal a otro. Si se acortan los terminales de las pilas podrían producirse quemaduras o incendios.
Español 11. Maneje correctamente la herramienta. Maneje la herramienta de acuerdo con las instrucciones ofrecidas aquí. No deje caer ni tire la herramienta. NO permita NUNCA que los niños ni otras personas no autorizadas ni familiarizadas con la operación de la herramienta utilicen ésta. 12. Mantenga todos los tornillos, pernos, y cubiertas firmemente fijados en su lugar. Mantenga todos los tornillos, pernos, y cubiertas firmemente montados. Compruebe periódicamente su condición. 13.
Español 5. 6. 7. La utilización de un accesorio no recomendado o vendido por el fabricante del cargador de baterías puede resultar en el riesgo de incendios, en descargas eléctricas, o en lesiones. Para reducir el riesgo de dañar el cable y el enchufe, para desconectar el cable del cargador de baterías, tire del enchufe. Cerciórese de que el cable quede situado donde no pueda pisarse, donde nadie pueda tropezar con él, y donde no pueda recibir daños. 8.
Español 9. 10. 11. 12. 13. 14. NUNCA utilice un transformador elevador para cargar. NUNCA utilice un motogenerador ni tensión de CC para cargar. NUNCA guarde la batería ni el cargador de baterías en lugares en los que la temperatura pueda alcanzar o sobrepasar 104°F (40°C). SIEMPRE utilice el cargador con un tomacorriente (120 voltios). La utilización de un cargador con cualquier otra tensión podría hacer que éste se recalentase y dañase.
Español ¡GUARDE ESTAS INSTRUCCIONES Y PÓNGALAS A DISPOSICIÓN DE OTROS USUARIOS Y PROPIETARIOS DE ESTA HERRAMIENTA! 46 03Spa_DS14DSAL_US 46 10/7/08, 16:18
Español DESCRIPCIÓN FUNCIONAL NOTA: La información contenida en este Manual de instrucciones ha sido diseñada para ayudarle a utilizar con seguridad y mantener esta herramienta eléctrica. NUNCA haga funcionar ni efectúe el mantenimiento de la herramienta antes de leer y comprender todas las instrucciones de seguridad contenidas en este manual. Algunas ilustraciones de este Manual de Instrucciones pueden mostrar detalles o accesorios diferentes a los de la propia herramienta eléctrica. NOMENCLATURA 1.
Español 2. Cargador de baterías (UC18YGSL) Riel de guía Lámpara piloto Placa de características Fig. 2 ESPECIFICACIONES 1. Taladro atornillador a batería Modelo Motor DS14DSAL Motor de CC Velocidad sin carga Capacidad Taladro Destornillador Baja Alta Madera (Grosor 11/16" (18 mm)) Metal (Grosor 1/16" (1.6 mm)) Tornillo para madera Tornillo pequeño Capacidad del portabrocas Battería Modelo Tipo Tensión Peso (sin gancho) 2.
Español MONTAJE Y OPERACIÓN ADVERTENCIA: No utilice el cargador si su cable está dañado. Haga que se lo reparen inmediatamente. APLICACIONES 䡬 䡬 Utilización como taladro Taladrado de materiales de acero dulce, madera, plástico, y aluminio. Utilización como atornillador Apriete y aflojado de tornillos para metal, tornillos para madera, y tornillos autorroscantes. 2. MÉTODO DE EXTRACCIÓN E INSTALACIÓN DE LA BATERÍA 1. Inserte la batería en la cargador.
Español Tabla 2 Indicaciones de la lámpara indicadora Lámpara piloto (rojo) Antes de la carga Parpadeo Se encenderá durante 0.5 segundos. No se encenderá durante 0.5 segundos. (Apagada durante 0.5 segundos) Durante la carga Carga completa Illuminación Iluminación permanente Parpadeo Se encenderá durante 0.5 segundos. No se encenderá durante 0.5 segundos. (Apagada durante 0.5 segundos) Parpadeo Espera por recalentamiento Batería recalentada. Se encenderá durante 1 segundo.
Español ● ● Si carga la batería mientras esté caliente por haber estado mucho tiempo en un lugar sometido a la luz solar directa, o por haber acabado de utilizarla, la lámpara de piloto del cargador parpadea durante 1 segundo y no se enciende durante 0.5 segundos (apagada durante 0.5 segundos). En tales casos, deje primero que se enfríe la batería e inicie luego la carga.
Español Marca de taladro Marca de Línea triángulo Botón pulsador Conmutador de gatillo Fig. 7 Marca R 6. Ajuste del par de apriete (1) Par de apriete La intensidad del par de apriete deberá correspond er con el diámetro del tornillo. Cuando se utiliza un par excesivo el tornillo se romperá o se dañará su cabeza. Asegúrese de ajustar la posición del dial del embrague de acuerdo con el diámetro del tornillo. (2) Indicación del par de apriete (Consulte la Fig. 6).
Español 䡬 La velocidad de rotación podrá controlarse variando la presión con la que tire del interruptor del gatillo. La velocidad será baja cuando se tire ligeramente del gatillo, y aumentará a medida que se tire más de él. (2) Colocación del gancho y ajuste de los tornillos. Instale el gancho en la ranura de la herramienta de alimentación eléctrica de forma segura y apriete los tornillos de manera que el gancho quede firmemente sujeto. (Fig.
Español Tabla 5 Trabajo Posición de la dial del embrague Sugerencias Madera Taladrado Acero Utilización para fines de taladrado. Aluminium Apriete de tornillos Tornillo pequeño 1 – 22 Utilice la broca y el cubo adecuados al diámetro del tornillo. Tornillos para madera 1– Utilice después de haber taladrado un orificio piloto. 13.
Español MANTENIMIENTO E INSPECCIÓN ● 1. PRECAUCIÓN: Extraiga la batería antes de realizar cualquier trabajo de inspección o de mantenimiento. Límite de uso Comprobación de las condiciones de la broca Las brocas deberán comprobarse regularmente. Si una broca está desgastada o rota, puede patinar o reducir la eficacia del motor, o hacer que se queme. Reemplace las brocas gastadas por otras nuevas. 0.12" (3 mm) 0.45" (11.5 mm) Fig. 13 ● 2. ● 3. 4.
Español 10. Lista de repuestos ● Fig. 15 Tubo exterior de la parte de contacto de la escobilla de carbón Fig. 16 6. 7. PRECAUCIÓN: La reparación, modificación e inspección de las herramientas eléctricas Hitachi deben ser realizadas por un Centro de Servicio Autorizado de Hitachi. Esta lista de repuestos será de utilidad si es presentada junto con la heramienta al Centro de Servicio Autorizado de Hitachi para solicitar la reparación o cualquier otro tipo de mantenimiento.
Español ACCESORIOS ADVERTENCIA: SIEMPRE utilice ÚNICAMENTE repuestos y accesorios autorizados por HITACHI. No utilice NUNCA repuestos o accesorios no previstos para usar con esta herramienta. Si tiene dudas en cuanto a la seguridad de usar determinado repuesto o accesorio junto con su herramienta, póngase en contacto con HITACHI. La utilización de otros repuestos o accesorios puede resultar peligrosa y causar lesiones o daños mecánios.
Español ACCESORIOS OPCIONALES.....de venta por separado 1.
03Spa_DS14DSAL_US 59 10/7/08, 16:18 Item No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 SPECIAL SCREW (LEFT HAND) M6 × 27 DRILL CHUCK GEAR BOX ASS’Y CLUTCH DIAL NUT SPRING THRUST PLATE FRONT CASE CLICK SPRING STEEL BALL D5 LOCK RING NEEDLE ROLLER RING GEAR CARRIER PLANET GEAR (C) SET PLATE (B) REAR CASE TAPPING SCREW (W/FLANGE) D2 × 3.
Please contact HITACHI KOKI U.S.A. LTD. at 1-800-59-TOOLS (toll free), or HITACHI AUTHORIZED POWER TOOL SERVICE CENTER regarding COLLECTION. Pour le RAMASSAGE, contacter HITACHI KOKI U.S.A. LTD. au 1-800-59-TOOLS (appel gratuit), ou UN SERVICE APRÈS-VENTE D’OUTILS ÉLECTRIQUE AGRÉÉ PAR HITACHI. Con respecto a la RECOLECCIÓN de baterías, póngase en contacto con HITACHI KOKI U.S.A. LTD. número 1-800-59-TOOLS (llamada gratis), o con HITACHI AUTORIZED POWER TOOL SERVICE CENTER. Issued by Hitachi Koki Co.