ֵ⭞䃠᱄ᴮ INSTRUCTIONS 㒣䦉 * 6:25' ȝ方様⃦ HITACHI G-SWORD ROTARY SHAVER RM-LTX7000DY RM-LTX7000 ਠ֒ᇬቻ⭞䙊 For household use only AC/RECHARGEABLE Made in Japan
1 2 3 4
5 8 6 9 13 7 10 11 14 15 12 16 (2) (1) 17 20 18 21 19 22
23 24 25 (2) (1) (2) (1) (1) 26 27 28 29 32 30 33 31 34
English Safety precautions Items described here are for using the product safely and properly, and to prevent hazards and injury to the user and other persons before they occur. Items are classified as follows. All items are important descriptions related to safety, therefore make sure to observe them. Extent of imminent hazard which has the potential to cause death or serious injury to the user in the case of improper handling.
Do not use the power adaptor and LED light dryer in a place where water is splashed, such as a bathroom, or in a place with high humidity. (Cause of electric shocks and short circuits) Prohibited Unplug Detach the hand-held part from the supply cord before cleaning it in water. Be sure to disconnect the power adaptor from the outlet and main body for maintenance. Never connect or disconnect the power plug to/from the outlet with wet hands. (Cause of electric shocks or injury) Never modify the shaver.
Never use any other power adaptor and LED light dryer than the ones included. Also, do not charge any other product with the included power adaptor. (Cause of fires by short circuits or abnormal heating) Prohibited Do not remove the main body from the LED light dryer during drying. (Cause of burns by the light emitting lens or foil that becomes hot during drying) Do not apply the trimming blade directly to ears and nose.
Mode indicator (Blue) Auto (flashing) Power (lighting), Normal (lighting off) Auto lamp (Green) The auto mode operates to light the lamp. Remaining battery level indicator lamp The capacity of the battery is displayed by three lamps. When the "EMP" lamp flashes during use, this indicates that charging is required. Charging completion lamp During charge: The lamp turns on. (Red) After charging is completed: The lamp turns off. Main body Center trimmer Swivels to securely catch beard.
Caution When the switch is turned "ON," this cannot be charged. When the capacity of the battery is sufficient, the charging completion lamp may be turned off early. Charging by using an LED light dryer (Included in the RM-LTX7000DY) Connect the power adaptor to the LED light dryer and an outlet, and insert the main body socket into the charging connector of the LED light dryer. (Fig.3) Caution If the dry switch is pressed by mistake, the dry switch will flash.
How to use It is recommended to use the shaver at an ambient temperature of 5°C to 35°C. Use or storage at a temperature below the recommended temperature may disable the shaver or cause a reduced number of operating times. For initial use, trim while lightly applying the shaver to skin. How to shave with the foil Check that there is no breakage and deformation of the foil before use. (Cause of damage to skin) Do not shave with the trimming blade down.
Power mode Beard can be shaved strongly and quickly at the time of start or in response to a thick beard. (Fig.11) Mode indicator “lights.” Auto lamp “turns off.” The auto lamp is "turned off." The mode indicator "lights (blue)." Normal Mode Beard can be shaved comfortably and softly in response to normal beard and finishing. (Fig.12) Mode indicator “turns off.” Auto lamp “turns off.” The auto lamp and mode indicator are turned off. When the switch is turned "OFF," the last mode is stored.
3. Turn "OFF" the switch and store the trimming blade after operation. (Fig.16) Caution Never place fingers on the upper side of the trimming knob. (The trimming blade will contact fingers at the time of storing.) If the trimming knob is pushed downward with the trimming blade contacting fingers, storage will be impossible due to the disconnected lever. Recommended If the trimming blade cannot be stored, move the trimming knob upward and downward once or twice to restore it without forcibly pushing it in.
3. After washing with water, wipe off water droplets on the main body and head holder. Lightly wipe off water droplets on the foil surfaces with tissue, etc. If wiping off is insufficient, water droplets may remain. CAUTION Never drain it by shaking. (Cause of the foil-cutter assembly coming off) 4. Press the lower part of the head holder removal button to attach the head holder. (Fig.21) Front (Notched side corresponds to the back side.) Push in the head holder until it clicks.
Do not remove the main body during drying (when the inscription “G-SWORD” on the dry switch lights). (Cause of burns by the light emitting lens or foil that becomes hot during drying) 5. After completion, take out the main body, and disconnect the power adaptor from the outlet. Caution : Never wash the LED light dryer with water. (Cause of failures) 6. After drying, apply the shaver oil, and keep it in a place free from moisture.
1. Turn "OFF" the switch to remove the cap and head holder. (Fig.17) Press the head holder removal button (1) to remove the head holder in the arrow (2) direction. 2. Detach the foil-cutter assembly. (Fig.28) Slide the foil-cutter assembly detaching knob to the right (1),pick up and pull both ends of the foil-cutter assembly straight upward (2) to detach it. Never pull it diagonally, otherwise, it may not be detached. 3.
Symptom - Failure of drying with the LED light dryer Check point Remedy Check for accumulation of dust, etc., inside the LED light dryer. Periodically perform maintenance. Check to see if water drops on the main body and blade surface have been wiped off after washing with water. Wipe off water drops on the main body and blade surface before setting. Check the above, and if the shaver is still in poor condition, do not repair by yourself but consult your distributor.