Gigabit Router Configuration Guide

Configuration Error Messages
GR2K-GA-0014 5-43
Ver. 07-02
ospf6: invalid hello-interval value at ’<Value>’
not in range 1 to 255
The hello-interval of OSPFv3 interface parameter is invalid. Specify
within the range of 1 to 255.
<Value>: Specified hello-interval value
ospf6: invalid instance value at ’<Value>’ not
inrange0to255
The OSPFv3 interface parameter instance is invalid. Specify within
the range of 0 to 255.
<Value>: Specified instance value
ospf6: invalid octet value at ’<Value>’ not in
range 0 to 255
More than 255 values are defined in dot notation. Specify value
within the range of 0 to 255.
<Value>: Specified value
ospf6: invalid OSPF6 cost value at ’<Cost>’
not in range 0 to 65535
The OSPFv3 cost in configuration information is invalid. Specify
within the range of 0 to 65535.
<Cost>: Specified cost value
ospf6: invalid OSPF6 interface cost value at
<Cost> not in range 1 to 65535
The OSPFv3 interface cost in configuration information is invalid.
Specify within the range of 1to 65535.
<Cost>: Specified interface cost value
ospf6: invalid preference value at <Value> not
inrange2to255
The preference value is invalid. Specify within the range of 2 to 255.
<Value>: Specified preference value
ospf6: invalid priority value at ’<Value>’ not in
range 0 to 255
The OSPFv3 interface parameter priority is invalid.
Specify within the range of 0 to 255.
<Value>: Specified priority value
ospf6: invalid range <Prefix>/ <Prefixlen> Incorrect (::/0) value was specified in the network range in the area
definition of the OSPFv3. Specify the value in other than ::/0.
<Prefix>: Specified prefix
<Prefixlen>: Specified prefix length
ospf6: invalid retransmit-interval value at
’<Value>’ not in range 1 to 65535
The interface parameter retransmit-interval in OSPFv3 area
definition is invalid. Specify within the range of 1 to 65535.
<Value>: Specified retransmit-interval value
ospf6: invalid router-dead-interval value at
’<Value>’ not in range 1 to 65535
OSPFv3 interface parameter router-dead-interval is invalid.
Specify within the range of 1 to 65535.
<Value>: Specified router-dead-interval value
ospf6: invalid transit-delay value at ’<Value>’
not in range 1 to 65535
OSPFv3 interface parameter transit-delay is invalid.
Specify within the range of 1 to 65535.
<Value>: Specified transit-delay value
ospf6: neighbor-id must be an IP address The IP address defined in the neighborhood is incorrect.
Specify it in the IP address form.
ospf6: net range already specified In the area definition of OSPFv3, the interface cost of an networks
parameter is double-defined. Do not double-define an networks
parameter.
ospf6: out of range The parameter-specified range is exceeded in the input command
syntax. Numeric values of more than 4294967296 are contained.
Reconfirm a parameter.
ospf6: Router ID not defined Router ID is not defined. Specify the Router ID.
ospf6: stub option not valid for backbone Stub parameter is defined in the OSPVv3 definition. Does not specify
stub parameter in backbone area.
ospf6: syntax error Syntax error
ospf6: this Router ID and Neighbor ID must be
different
The local router ID must be different from the adjacent router ID of a
virtual link.
ospf6: transit-area can not be the ’backbone’
area
The passage area of a virtual link is defined in a backbone area.
Define the passage area in areas other than the backbone area.
ospf6: virtual links only allowed in ’backbone’
area
The hypothetical link is defined in an area other than the backbone
area. Define it in the backbone area.
rip: duplicate interface address in list at
<Address>
Interface address definition is duplicated in rip.
Use a unique interface address.
<Address>: Specified interface address
Table 5-5 Routing Protocol Error Messages (continued)