Gigabit Router Configuration Guide

Configuration Error Messages
GR2K-GA-0014 5-47
Ver. 07-02
route-filter: invalid domain-number value at
<Domain Number> not in range 1 to 65535.
OSPF or OSPFv3 domain number is out of valid range. Specify a
value within the range of 1 to 65535.
<Domain Number>: Specified domain number
route-filter: invalid high end of range value at
<Value> not in range 0 to {32|128}
In the between specification, upper limit value of mask range is
invalid. Specify a value within the range of 0 to 32/128.
<Value>: Upper limit of Specified Mask range
route-filter: invalid index number in extended
community number value at <Value> not in
range 0 to { 65535 | 4294967295 }
Specified range of ID number in extended community is invalid.
Specify in the range of 0 to 65534 /4294967295.
<Value>: Specified ID number
route-filter: invalid {inet|IPv6} mask bits value
at <Value> not in range 0 to {32|128}
At masklen/prefixlen, the mask length is valid. Specify value within
the range of 0 to 32/128.
<Masklen>: Specified mask length
route-filter: Invalid interface name ’<Interface
Name>’
The multi-home interface is specified. Do not specify multi-home
interface.
<Interface Name>: Specified interface name
route-filter: invalid localpref value at
<Localpref> not in range 0 to 65535
Specified LOCALPREF value is out of valid range. Specify value
within the range of 0 to 65535.
<Localpref>: Specified LOCALPREF value.
route-filter: invalid localpref offset value at
<Localpref> not in range 1 to 65535
Specified LOCALPREF offset value is out of valid range. Specify
value within the range of +1 to +65535 or -1 to -65535.
<Localpref>: Specified LOCALPREF offset value.
route-filter: invalid low end of range value at
<Value> not in range 0 to {32|128}
In the between specification, lower limit value of mask range is
invalid. Specify a value within the range of 0 to 32/128.
<Value>: Lower limit of specified mask range value
route-filter: invalid network-filter number value
at <Value> not in range 1 to 65535
ID number is out of valid range. Specify value within the range of 1 to
65535.
<Value>: Specified ID number
route-filter: invalid number of communities
value at <Value> not in range 0 to 25
Specified community count is over the limit. Specify a value up to 25.
<Value>: Specified community count
route-filter: invalid number of extended
communities value at <Value> not in range 1
to 25
The number of extended communities to be defined exceeds the
maximum number of extended communities to be defined. Specify a
value of 25 or less.
<Value>: Extended community number
route-filter: invalid octet value at <Value> not
inrange0to255
More than 255 values are defined in dot notation. Specify value
within the range of 0 to 255.
<Value>: Specified value
route-filter: invalid policy group number value
at <Group Number> not in range 1 to 16
Policy group number is out of valid range. Specify a value within the
range of 1 to 16.
<Group Number>: Specified mask length
route-filter: invalid preference value at
<Value> not in range 2 to 255
Range of specifying the preference value is incorrect. Specify in the
range of 2 to 255.
<Value>: Specified preference value
route-filter: invalid range end: <Value> In Aspath_term {m, n}, m>n or n is 0. Specify start value less than
end value or assign a value other than 0 to the end value.
<Value>: Specified end value(n)
route-filter: invalid range start: <Value> In aspath_term {m, n}, {m}, {m,}, m is 0. Specify a value other than 0.
<Value>: Specified start value (m)
route-filter: invalid route-filter number value at
<Value> not in range 1 to 65535 value
ID number is out of valid range. Specify value within the range of 1 to
65535.
<Value>: Specified ID number
route-filter: invalid route-filter sequence
number value at <Value> not in range 1 to
65535
Sequence number is out of valid range. Specify value within the
range of 1 to 65535.
<Value>: Specified sequence number
Table 5-5 Routing Protocol Error Messages (continued)