3-CCD Color Camera MODEL HV-D25 OPERATION MANUAL Please read this operation manual carefully for proper operation, and keep it for future reference. Note: The model and serial numbers of your product are important for you to keep for your convenience and protection. These numbers appear on the nameplate located on the bottom of the product. Please record these numbers in the spaces provided below, and retain this manual for future reference. Model No. Serial No. Hitachi Denshi, Ltd.
IMPORTANT SAFETY INSTRUCTIONS 1. Read Instructions All the safety and operating instructions should be read before the product is operated. 2. Retain Instructions The safety and operating instructions should be retained for future reference. 3. Heed Warnings All warnings on the product and the operating instructions should be adhered to. 4. Follow Instructions All operating and use instructions should be followed. 5. Cleaning Unplug this product from the wall outlet before cleaning.
12. Grounding or Polarization This product is equipped with a three-wire grounding-type plug a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. 13.
amplifiers) that produce heat.
WICHTIGE SICHERHEITSANWEISUNGE 1. Alle Anweisungen lesen. Vor Betrieb des Erzeugnisses sollten alle Sicherheits-und Bedienungsanleitungen gelesen werden. 2. Die Anweisungen aufbewahren. Die Sicherheits-und Bedienungsanleitungen sollten fünftigen Bezug aufbewahrt werden. 3. Warnungen beachten. Die Warnungen auf dem Erzeugnis und in den Bedienungsanleitungen solten beachtet werden. 4. Anweisungen befolgen. Alle Bedienungsanleitung-und Verwendungsanweisungen sollten befolgt werden. 5.
11. Stromversorgung Dieses Erzeugnis sollte nur an der auf dem Typenschild angegebenen Stromversorgungsart betrieben werden. Wenn Sie nicht sicher sind, was für eine Stromversorgung Sie haben, so wenden Sie sich bitte an Ihren Erzeugnishändler oder an das lokale Elektrizitätswerk. Beziehen Sie sich für Batteriebetrieb oder andere Stromquellen vorgesehene Erzeugnisse bitte auf die Bedienungsanleitungen. 12.
20. Beschädigung, die Wartung erfordert Ziehen Sie den Stecker dieses Erzeugnisses aus der Steckdose und wenden Sie sich an qualifiziertes Wartungspersonal, wenn eine der folgenden Bedingungen vorliegt: a. Wenn das Netzkabel oder der Stecker beschädigt ist. b. Bei Eindringen von Flüssigkeit oder Fremdkörpern in das Gerät. c. Wenn das Erzeugnis Regen oder Wasser ausgesetzt worden ist. d. Wenn das Erzeugnis bei Befolgen der Bedienungsanleitungen nicht normal funktioniert.
MISES EN GARDE IMPORTANTES 1. Lire les instructions Lire toutes les instructions de sécurité et de fonctionnement avant de faire fonctionner l’appareil. 2. Conserver ces instructions Conserver les instructions de sécurité et de fonctionnement á des fins de référence ultérieure. 3. Tenir compte des avertissements Tous les avertissements qui figurent sur l’appareil et dans le mode d’emploi devront être respectés. 4. Observer les instructions Observer toutes les instructions de fonctionnement et d’utilisation.
12. Mise á la terre ou polarisation L’appareil est doté d’une fiche trifilaire avec mise á la terre, dont la troisiéme broche assure la mise á la terre. Cette fiche ne rentrera que dans les prises trifilaires de mise á la terre. Ceci est une mesure de sécurité. Si la fiche ne rentre pas dans la prise, faire remplacer la prise désuéte par un électricien. Ne pas rendre vaine la measure de sécurité assurée par cette prise avec mise á la terre. 13.
21. Piéces de rechange Si l’on a besoin de piéces de rechange, veiller á ce que le technicien de réparation utilise exclusivement les piéces de rechange spécifiées par le fabricant ou des piéces ayant les mêmes caractéristiques que les piéces d’origine. Les piéces de rechange non autorisées risquent de provoquer un feu, un choc électrique et autres dangers. 22.
IMPORTANT NOTICE For USA These products have been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Table of contents l IMPORTANT SAFETY INSTRUCTUIONS ........................................................................ A l IMPORTANT NOTICE....................................................................................................J l Table of contents......................................................................................................... K l Standard composition .................................................................................................1 l Overview ......
l Application files ........................................................................................................31 l How to Attain Better images ........................................................................................33 Black Balance Adjustment.......................................................................................33 White Balance Adjustment.......................................................................................34 Real time Auto White................
Standard composition Check when unpacking. Camera, HV-D25 ................................................................................................................................1 Lens mount cap ..................................................................................................................................1 Power plug, RM12BPG-3S (JMR0152*)................................................................1 Remote plug, HR10A-7P-4P (01) (JMH2011*) ..................................
• Digital processing enables wide array of functions Desired hue and tint can be adjusted with 6-vector independently variable masking. Even at wide dynamic range, auto-knee and dynamic chroma can provide superbly colored images. The versatile detail compensating functions allow optimum contour compensation to match the scene.
l Lens The correct lens is important for deriving optimum performance from the camera. Consult a Hitachi Denshi dealer for a selection of fine lenses according to the application. l Installation and storage sites The following types of environment can impair performance, lead to damage, pose safety hazards and shorten the useful life of the camera. Select the sites for installing the storing the camera carefully.
3) Moire Interaction between patterns can produce an additional "phantom" pattern to appear. The CCD picture elements (pixels) are arranged in a pattern, which can interact with a pattern in the scene (e.g., a performer wearing a finely striped necktie) to result in a Moire pattern. The effect should be considered when selecting costumes, props and other scene elements. 4) Ghosting Strong direct or reflected light near an object of interest can cause ghosting of the object to appear in the picture.
Rear panel facilities AWB/L button Direct mode (menu not displayed): Hold the button depressed for more than 2 seconds for auto white balance. Menu mode (menu displayed): Left direction button. Pilot lamp SETUP button VIDEO connector Composite video signal output (1Vp-p/75 ohms). Press to display the camera setup menu. The direction (U, D, L, R) button functions differ in the menu and direct modes. REMOTE connector Connect a remote control box (RC-C10) or a personal computer.
Lens Note when choosing the lens The figure indicates the limiting dimensions of the lens mounting structure. Use care, since an improper lens fitting can damage both the lens and the camera. 1) The C mount threads must be less than 4.2 mm from the flange plane. 2) An 18 mm diameter segment of the lens optical axis center must be must be less than 3.8 mm from the flange plane. Lens selection 1) Optical characteristics The proper lens is vital for obtaining full performance from the camera.
Flangeback adjustment If focus cannot be adjusted after replacing the lens or at the telephoto and wide angle extremes of a zoom lens, the flangeback can be adjusted. Open the lens iris and adjust as described below. Fixed focus lens Set the lens focus ring to infinity and pickup an image more than 20 meters distant. While observing the picture, adjust the focus by turning the flangeback ring in the F or N direction. Zoom lens 1) Set the lens to telephoto and pickup an image more than 3 meters distant.
2) Adjustment Hold the U button depressed and press Setup for about 2 seconds to display the Special Set menu. Change to the Lens screen and check the Lens Type setting. If DC, change this to Video. < LENS (APP-1) LENS TYPE :VIDEO IRIS GAIN : 0 REFERENCE Video signal indicator H L Video mode menu screen (1) Set the lens ALC control fully toward the average (Av ) position. (2) If auto iris hunting occurs, reduce the Iris Gain setting.
Camera mounting The camera is provided with threaded screw holes at the top and bottom. These allow mounting to either a tripod or a mounting bracket. Screw type ‚k U 1/4-20 Length: 4.5 to 6 mm Screws longer than 6 mm can cause internal damage, while less than 5 mm prevents secure fastening and risks dropping to cause damage and injury.
System examples Color monitor Surveillance and TV conferencing Lens Camera VBS RC-C10 Remote box REMOTE DC IN Personal computer Lens remote unit * RS-232C * A level converter is required if controlling the camra from a personal computer via RS-232C interface over a distance more then 15 meters.
Microscope ststem Color monitor VBS R G B SYN C Y/C D-Sub 9pin DC IN VBS REMOTE Y/C Remote control box RC-C10 Camera Personal computer Microscope AC Adaptor Computer image processing D-Sub 9pin Lens Camera Personal computer R G B SYN C REMOTE DC IN AC Adaptor 11
Multi-camera computer control Lens Camera no.1 VBS Video signal switcher Color monitor REMOTE DC IN AC Adaptor Personal computer JU-Z2 Camera control box Lens Camera no.8 VBS When using the JU-Z2 for multiple camera control, set the camera internal SW405 to RC-C10. See page 34.
Notes When Using Cables l AUX Cable Use double shielded type cable. l RC Cable As shown in the following figure, install clamp filter (ZCAT 2035-0530 : TDK) at camera end . Y/C Cable Use after winding a cable around a clamp filter (NTSC: ZCAT2035-0930 TDK) (PAL: ZCAT24361330 TDK) once at camera end as shown in the following figure.
Menu Screen Operation 1. Menu Structure For settings in the camera, the MAIN and SPECIAL menus are available. 1-1 MAIN Menu Structure Press the SEUTP button and MAIN MENU appears on the screen to indicate the main menu mode. Again press the SETUP button to extinguish the menu and enter the direct mode. There are a main function setup menu and three sub-menus, which are arranged hierarchically as shown below.
1-2 SPECIAL Menu Structure To select the SPECIAL SET mode, press the SETUP button for 2 seconds while holding down the U button. Thus, the SPECIAL SET menu can be displayed. To return to the DIRECT mode, press the SETUP button again. The SPECIAL SET menu indicates a list of items, and each special items subsidiary menus are available. These menus are arranged hierarchically as shown below. On the SPECIAL SET menu, most items have '->' mark at the right side.
2. MAIN MENU CAM MODE: Camera mode l MANUAL : Nearly all function modes can be set. Use for detailed settings. l AUTO : Video level and white balance are automatic and a standard picture cam be observed without detailed settings. Asterisk (*) indicates a fixed setting and the cursor jumps to the next item. The Auto indication flashes when a function is related to the auto mode. At the Lens menu, the shutter mode changes according to the Lens Type setting.
3) GAIN:Gain mode L R NORMAL HIG X A M C G A • NORMAL:The gain level is set to 0 dB. • HIGH: The gain level is set to a value specified at GAIN HIGH on the SUB menu 1. • MAX: The gain level is set to a value specified at GAIN MAX on the SUB menu 1. • AGC: An increase in gain is controlled automatically. The upper limit of gain to be increased corresponds to a value specified at AGC on the SUB menu 2. In the Auto CAM mode, gain is fixed at AGC.
3. SUB MENU 1 1) M BLACK:Master black level setting The master black level can be set in a range of -128 to 127. Pressing the R button increases a set value to make the black level higher, and pressing the L button decreases a set value to make the black level lower. For zero (0) setting, hold down both the L and R buttons for approx. two seconds.
4)CCD MODE:CCD store mode changeover • FLD: The field store mode operation is performed (for ordinary purpose of application). • FRM:Frame store mode operation is performed. The vertical resolution can be increased but the degree of after-image becomes slightly higher. It is therefore recommended to use the FRM function when taking a still image. (Note) When the shutter mode is AES, even if set to frame, the camera operates in the field mode. In the Auto CAM mode, The CCD mode is set to FLD.
4. SUB MENU 2 1) DYNA CHROMA:Dynamic chroma ON/OFF With knee on, setting the dynamic chroma on improves coloration in bright portions of the scene. 2) CHROMA GAIN:Level setting in chroma signal The chroma signal level can be set in the range of -128 to +127. Respectively press the R button to increase and the L button to decrease the chroma signal level. Set the level to 0 by simultaneously pressing both L and R buttons for about 2 seconds.
10) WHITE GATE:White gate ON/OFF ON: In realtime auto white balance operation or execution of memory auto white balance, a video signal appearing in the window on screen is detected for white balancing. < SUB MENU2 (APP-1) In the MENU mode, the window is presented over the DYNA CHROMA :OFF video signal. For the setting procedure, refer to 'WHITE CHROMA GAIN :+ 10 CONTRAST :OFF GATE Menu of SPECIAL SET Menu' (p. 25).
6. SPECIAL SET 1) REMOTE: Remote control baud rate setting For baud rate setting, use the L and R buttons. (Note) When setting a baud rate, do not connect the communication cable with the REMOTE terminal. L s p b 0 5 2 6 • R s p b 0 8 4 960bps 1920bps 62500bps: Select this baud rate when using the RC-C10 remote control box. In this case, be sure to also set the RC-C10 baud rate to 62500 bps. Refer to the RC-C10 operating instructions.
7. LENS Menu for setting the lens functions 1) LENS Type: Sets type of auto iris. • DC :Iris opens in proportion to a DC control voltage. Also set to DC when not using an automatic iris. • Video: Lens iris is controlled by the video signal. (Note) Auto electronic shutter (AES) cannot be used in the Video mode. The menu screen changes according to the Lens Type setting.
6) CLOSE Limit: (Lens Type is DC mode.) Observe the iris and adjust to precisely the largest value (smallest diameter). The setting range is from -128 to Close Limit -1. Press R to increase and L to decrease the setting. Press L and R buttons simultaneously for about 2 seconds to set to -85 for Cosmicar or to -65 for Others. Notes: 1 Before this adjustment, set Gain to Normal and Shutter to Off. Return the previous settings after adjusting.
8. IRIS GATE This menu screen allows you to make iris gate (window) settings. 1) GATE AREA :The window can be shifted up/down. To shift the window up, press the R button. To shift it down, press the L button. 2) GATE AREA:The window can be shifted left/right. To shift the window rightward, press the R button. To shift it leftward, press the L button. 3) GATE AREA:The size of the window can be adjusted. Using the L or R button, you can select one of four window sizes.
3) R GAIN: R gain level setting The allowable setting range is -128 to 127. Pressing the R button increases a numeric value to make the R video signal gain higher. Pressing the L button decreases a numeric value to lower the R video signal gain. For 0 (zero) setting, hold down both the L and R buttons for approx. two seconds. 4) B GAIN:B gain level setting The allowable setting range is -128 to 127. Pressing the R button increases a numeric value to make the B video signal gain higher.
139 INITIALIZE: Mask settings are initialized to factory values for each application file. Simultaneously press the L and R buttons for about 2 seconds to return the selected files to the factory settings. See Page 25 for the factory settings of each application file. 12 OUTPUT/SYNC On this menu screen, you can make signal changeover for output to the D-SUB connector and phase adjustment for external synchronization.
6) SC.COARSE:Coarse adjustment of subcarrier phase L ‹ • 0 R ‹ • 0 9 ‹ • 0 8 1 ‹ 270• Using the L or R button, select one of the following phases; 0º, 90º, 180º and 270º. 7) SC.FINE:Fine adjustment of subcarrier phase The allowable setting range is -128 to 127. There is no direct relationship between a numeric value and a degree of phase. If the relevant range is exceeded, the SC COARSE setting is updated automatically to permit continuous adjustment. 8) H.
Œ With the cursor located at DATA SET, press the D button. The cursor moves to the ID data set position an the first character flashes. • Using the L, R, U and D buttons, select an input character. Ž Press the SET UP button, and the selected character will be entered. (The cursor will then move to the next character position.) • In the same manner, repeat the above steps • On completion of character input, bring the cursor to RET using the L, R, U or D button.
15. GAMMA Menu for setting the gamma parameters. If dark component contrast is inadequate, adjusting the gamma parameters allows detailed adjustment of the Sub-menu 2 Contrast (Off, Normal, High). 1) GAMMA TABLE: Sets gamma rising slope. Low:Dark component gradation reduced. Standard:Standard setting High:Dark component gradation increased. 2) TOTAL GAMMA: Sets total (R, G and B) gamma point Setting range is from -128 to 127. Press R to raise and L to lower RGB video signal gamma point.
Application Files (APP-1,APP-2,APP-3) Camera setting data can be stored in three application files. These enable optimizing the camera for specific scene and lighting conditions, then storing the setting data in memory for quick recall at the appropriate time. The application files have been set at the factory as follows. APP-1: Standard type camera settings APP-2: General purpose surveillance and TV conferencing APP-3: Microscope settings.
2. Common file settings The settings of these items apply to all files. They cannot be set differently for each file. The table indicates the factory settings. Menu item Setting data MAIN MENU Setting data Menu item SEPECIAL SET CAM MODE MANUAL ULTRA GAIN OFF SUB MENU 1 VARIABLE Menu item REMOTE 62500bps LENS SELECTION NTSC:1/60.
How to Attain Better Images Black Balance Adjustment Adjust black balance to provide proper color tone at a dark part of video image. In the following cases, be sure to carry out black balance adjustment. • When using the camera first after purchasing it. • When using the camera after it has been unused for a long time. • Wen the camera operating environment is changed (e.g., when the ambient temperature varies significantly).
White Balance Adjustment Carry out white balance adjustment when the illumination condition (color temperature) is changed. Adjust the white balance when using the camera for the first time or after replacing the lens. 1. In the MENU mode, set up WHITE BAL: MEM 3200K or MEM 5600K. 2. Turn off the MENU screen to select the DIRECT mode. 3. Provide a proper aperture value of lens using the auto iris function or manually. 4. Put an white object in the subject image, and zoom it up. 5.
AUTO WHITE:NG C. TEMP HIGH CHANGE TO MEM 5600K • Color temperature too high for optimum adjustment. • Set WHITE BAL to MEM 5600 K mode. TRY AGAIN AUTO WHITE:NG C. TEMP LOW CHANGE TO MEM 3200K • Color temperature too low for optimum adjustment. • Set WHITE BAL to MEM 3200 K mode. TRY AGAIN AUTO WHITE:NG LONG SHUTTER MODE • Release the long shutter mode. CHANGE SHUTTER MODE TRY AGAIN CAM MODE:AUTO CHANGE TO MANUAL • Set camera mode to manual.
Realtime Auto White The camera detects a white part in the image by itself, and its internal microcomputer automatically adjusts white balance in realtime. Use this function in case that the color temperature varies with time (e.g., from morning to day to night). 1. In the MENU mode, set up WHITE BAL:AUTO. (Note 1) If the color temperature of the scene being taken is changed abruptly (when the camera is oriented from indoor side to outdoor side), the image may become bluish or reddish momentarily.
ALC In combination of GAIN:AGC, SHUTTER:AES and AUTO IRIS, the following four kinds of ALC (auto level control) can be performed. This feature ensures stable video signal output according to a wide-range change in illumination. Note: 1 AES cannot be combined with a Video type lens. 2 When not using an auto iris lens, at the Lens menu, set Lens Type to DC and Iris Mode to Manual.
Lock scan mode shutter speed setting 1 Press the Setup button and open the main menu, then open Sub menu 1. Set the cursor to SHUTTER by pressing D, select the VARIABLE position with the L-R buttons, again press D to shift to the variable items. 2 Press the L and R buttons to set the shutter speed in the range indicated below. Set the desired shutter speed. L R 1/60.38 •` (1/50.31 : PAL) 1/251.5 (1/253.8 : PAL) When picking up e.g.
Long-Time Store Mode In case that illumination on the subject is insufficient, just increasing the gain of the camera may cause an increase in noise, resulting in an unclear image. In such a situation, it is advisable to select the long-time store mode using the external memory. Thereby, the image can be brighter and clearer according to the stored amount of image. This camera is provided with two kinds of image store functions (CCD MODE:FLD/FRM in SUB MENU 1).
Connection to RC-C10 remote control box The HV-D25 camera can be remotely controlled from the RC-C10 remote control box. Adjustments and operations not provided on the RC-C10 panel can be set from the HV-D25 camera menu. RC-C10 buttons corresponding to the menu screen are Option 1, Option 2, Auto White and Auto Black.
1 ABB/R (auto black balance/right) button Direct mode :Black balance is adjusted automatically. Menu mode :Execute or change function data. 2 AWB/L (auto white balance/left) button Direct mode :White balance is adjusted automatically. Menu mode :Execute or change function data. 3 Lock switch Left position :Genlock (GL) adjustment Right position :R/B gain and R/B black fine adjustment Center position:Adjustments inoperative.
11 Set button When pressed, control data are stored and the LED lights for about 1 second. l Notes: 1 Be sure to press the Set button in order to save the setting data before switching off power. Otherwise the data are lost and old data are returned at power on. Also, the old data are deleted by pressing the Set button. 2 The Set button operation differs between the RC-C10 and RC-C10(R1). The RC-C10 stores the panel adjustment and operation data.
2.MenuscreenOperation Menu screen customizing Camera settings other than the RC-C10 panel can be customized at the Main and Special set menu screens. 2-1. Main menu screen Press the Setup button 10 to produce the menu mode and display the main menu screen. Again press the Setup button 10 extinguish the menu screen and produce the Direct mode. The menu contains 3 submenus for setting the major functions, which are organized as indicated below.
2-2. Special menu screen Hold button D 9 depressed and press the Setup button 10 for 2 seconds to display the Special set menu and produce the menu mode. To return to the direct mode, again press the Setup button to 10 extinguish the menu. At Special Set menu items indicated by ->, press the ABB/R button 1 item. Press button 9 D to shift to the submenu for setting the to shift the cursor to the submenu item to be changed, then press AWB/L or ABB/R 2 , 1 to change the mode or data.
3.Application files (APP-1, APP-2 and APP-3) The application files can be changed during remote control from the RC-C10. The HV-D25 camera is preset at the factory according to the application. • APP-1:Standard camera settings • APP-3:General surveillance, TV conference • APP-3:Microscope setting. Masking is set for optimum color reproduction at color temperatures of 5000 K light source and 9200 K color monitor. Select the appropriate file for the application.
3-2.Items stored in common file Common file settings are indicated below. Different settings for these items cannot be stored in the application files. The indicated data are for the factory settings. Notice there are some differences during local control of the HV-D25 camera. Menu items Setting data Menu items MAIN MENU CAM MODE MANUAL ULTRA GAIN OFF SUB MENU 1 VARIABLE Setting data IRIS GATE UP/DOWN CENTER White balance mode LEFT/RIGHT CENTER Gain mode LARGE/SMALL NTSC:1/60.38 PAL :1/50.
Function Selection by Internal Switch Setting SW405 For connection with the remote control box RC-C10, set SW405 to the RC-C10 position. For connection with the personal computer, set SW405 to the RS-232C position. At shipment from factory, SW405 is set at the RC-C10 position. Connectors MULTI connector (SDEB-9S) Pin No. Signal designation REMOTE connector (HR10A-7R-4S) Pin No.
LENS connector Pin No. AUX connector (HR10A-10R-12PB) Signal Pin No. Signal designation 1 +12V 1 GND 2 NC 2 NC 3 Control 3 EXT CONT 1 4 GND 4 EXT CONT 2 5 GND 6 HD input 7 VD input 8 EXT CONT 3 9 EXT CONT 4 10 GND 11 NC 12 GND Y/C connector (TCS-7547-01-401) Pin No. Signal designation 12V-IN connector (RM12BRD-3PH) Pin No.
Specifications (1) Color system NTSC,PAL (2) Optical system 1/2-inch F1.6 prism (3) Imaging system RGB 3-chip (4) Imaging device 1/2-inch interline CCD (with microlenses) Total pixels NTSC: 811 (H) × 508 (V) PAL : 795 (H) × 596 (V) Effective pixels NTSC: 768 (H) × 494 (V) PAL : 752 (H) × 582 (V) Effective image area 6.45 (H) × 4.84 (V) mm 6.47 (H) × 4.83 (V) mm (5) Encoder system R-Y/B-Y (6) Sync system Internal/external (Automatic changeover VBS/BBS or HD/VD.
(19) CCD drive functions Preset 1/100 (1/60 PAL), 1/250, 1/500, 1/1,000, 1/2,000, 1/4,000, 1/10,000 second Lockscan NTSC: 1/60.38 to 1/251.5 second (1 H steps) PAL : 1/50.31 to 1/253.8 second (1 H steps) AES Off to approx. 1/1,000 second (up to equivalent of 4 F stops, continuously variable in 1 H steps) Long integration Selectable field/frame integration NTSC: 1/30 to approx. 8 seconds (1 frame steps) PAL : 1/25 to approx.
Input/Output Signals 1. Input signal (1) Genlock input VBS 1.0 Vp-p ± 3 dB or black burst, 75Ω or high impedance (BNC) (Sync 0.3 ± 0.1 Vp-p, burst 0.3 ± 0.1 Vp-p) HD/VD TTL level (AUX connector) and 4.0 +0,-1Vp-p (2) Serial data (4 pin connector) 1.5 Vp-p ± 3 dB, high impedance (in connection with RC-C10) RS-232C level (in connection with personal computer) (Note) Set internal switch according to connected equipment. 2. Output signal ratings (1) Composite video (BNC, D-sub connector) VBS 1.
Major accessories Camera control box, RC-C10 Camera Junction box, JU-Z2 RS-232C level converter JU-C20
Dimensions