JPEG2000 Stand alone DVR User Guide CONTENTS Date: 2006/07/05 VER: 1.5 Caution ……………………………………………………………………. 3 Package ……………………………………………………………………. 3 Specification ……………………………………………………………………. 4 CHAP.1 Appearance 1-1 Front panel introduction ……………………………………………………………………. 6 1-2 Back panel introduction ……………………………………………………………………. 8 1-3 IR remote controller introduction ……………………………………………………………………. 9 CHAP.2 Installation 2-1 Camera and monitor installation …………………………………………………………………….
JPEG2000 Stand alone DVR User Guide CHAP.5 CD-R bck-up 5-1 Data backup …………………………………………………………………… 44 5-2 CD-R player software installation …………………………………………………………………… 45 5-3 CD-R player software interface …………………………………………………………………… 46 CHAP.6 PTZ camera control 6-1 PTZ camera installation …………………………………………………………………… 48 6-2 PTZ camera operation …………………………………………………………………… 49 CHAP.
JPEG2000 Stand alone DVR User Guide Caution For you safety, unplug the power before moving the DVR, installing, or replacing any parts or hard drive. Make sure all the power cable and wires are properly set up before using the DVR. Contact your distributor immediately if there is any defect. To avoid a short circuit, don’t leave any unnecessary parts inside the DVR. Please avoid dramatic changes of the environment, such as dust, temperature, and humidity. Keep the DVR in a temperature ranging from 5℃~40℃.
JPEG2000 Stand alone DVR User Guide Specification Model 4/8/16 CH JPEG2000 Stand Alone DVR Video Input Video I/O Video Output 4/8/16CH VIDEO IN 1.
JPEG2000 Stand alone DVR User Guide Protocol Network Remote monitoring Back-up PTZ Control RS232 TCP/IP Remote Softeware: Remote live view, playback, and save as AVI IE: Remote live view, backup, and save backup to AVI VCR, CD-R back-up, Backup via IE RS485,supports PELCO D and other protocols Controls DVR host through RS232 4CH: 4 Alarm Inputs Alarm Input Assistant Functions 16CH: 16 Alarm Inputs Alarm Output Remote Controller 1(Programmable alarm output duration) Infrared Remote Controller Control De
JPEG2000 Stand alone DVR User Guide CHAP.1 Appearance 1-1 Front panel introduction 1.[CD-RW] Built-in CD-RW for CD-R back-up. 2.[IR Receiver & LED Lamps] IR Remote Controller Receiver. DVR Status LED: RUN- Flashes when play picture by picture through J. Shuttle. ACTIVE- On when the J. Shuttle is ready to use. REC- On while recording and flashes at stand-by mode, such as no motion triggered at the motion record mode PLAY- On while playback. FULL- On when HDD storage is full.
JPEG2000 Stand alone DVR User Guide 10.[Control] SEQ- Full screen sequencing or the smaller screen sequencing in PIP mode. PIP- For entering the Picture in Picture mode from full screen mode. NEXT- Switch other control keys in PTZ mode. Switch to other channel in a split screen. ZOOM- To enlarge the picture. Use the direction buttons and move to the area to be enlarged. 11.[REC] To activate Emergency Record at continuous, Super fine quality and Best resolution. Press STOP to exit the Emergency Record mode.
JPEG2000 Stand alone DVR User Guide 1-2 Back panel introduction [4Channel] [8Channel] [16Channel] 1.[RS485, Relay Output, Sensor Input] RS485, for direct connection to PTZ cameras. 16 sensor inputs and 1 relay output. 2.[VGA Output] Connection to a VGA monitor or TFT LCD. 3.[ETHERNET] Connection to Ethernet device. 4.[RS-232C] Connection to PC or other DVR control devices. 5.[1~16 Camera Input/LOOP Output] CAMERA IN- channel 1~16 camera input.
JPEG2000 Stand alone DVR User Guide 1-3 IR remote controller introduction 1.[MENU] Enter menu or exit 2.[Split /OSD] 4S: 4 split 9S: 9 split 16S: 16 split OSD: OSD words on/off 3.[1~16 Channel] Switch channel in live or playback; password entering 4.[Control function] FRZ- Freeze the screen in display SEQ- Automatically display full screen or split screen in sequence ZOOM- To enlarge the picture. Use the direction buttons and move to the area to be enlarged. PIP- Picture in Picture.
JPEG2000 Stand alone DVR User Guide CHAP.2 Installation 2-1 Camera and monitor installation 2-1-1 Camera installation Connect camera to DVR camera in CH1~CH16 ※Please do not start the DVR before the camera. installation is done. 2-1-2 Monitor and VCR installation Monitor: Connect the MONTIOR port on the DVR back panel to the “video in” port on the monitor. VCR: Connect the VCR port on the DVR back panel to the “Video In” on the VCR.
JPEG2000 Stand alone DVR User Guide 2-1-3 Loop out installation To monitor a single channel, connect the “loop out” of the corresponding channel to a monitor. To record a specific channel individually, connect the “loop out” of the corresponding channel to a DVR, VCR, or other record device. 2-2 Sensor and alarm installation 2-2-1 Input & Output 1.[D1~D16 Alarm Input/GND for Location] 16 Sensor inputs, for sensor input installation 2.
JPEG2000 Stand alone DVR User Guide 2-2-3 Relay output installation Alarm output can be NO or NC, depending on the settings. NO-COM: the NO and COM terminals are open-circuit, and it’ll become closed-circuit when alarm triggered. NC-COM: the NC and COM terminals are closed-circuit, and it’ll become open-circuit when alarm triggered. 2-3 Network and serial port installation 2-3-1 Network setup Connect the network cable to “Ethernet”on back panel. Ethernet Setup between ADSL and Cable is different.
JPEG2000 Stand alone DVR User Guide connector description 1 2 3 4 5 6 7 8 9 DCD RxD TxD DTR GND DSR RTS CTS NC ASCII-CODE Func. CODE Func. CODE Func. CODE Func. CODE Func. CODE REC R RIGHT K MODE D CH3 3 CH11 ! STOP S NEXT N PIP I CH4 4 CH12 @ PLAY P ENTER 0X0D SEQ Q CH5 5 CH13 # SEARCH E - < J.
JPEG2000 Stand alone DVR User Guide 2-4 HDD installation [Steps] 1. Disassemble the bolts as illustrated. 2.Jumper setting Set up the HDD as MASTER or SLAVE. Please refer to the HDD manual of the jumper settings. 3.HDD Installation Please insert the HDD as shown in , and make sure the HDD is set as “MASTER”. Caution: 1. Power off the DVR before HDD installation. 2. Jumper setting must follow the instruction of HDD manufacturer. 3.
JPEG2000 Stand alone DVR User Guide 2-5 Power plugging Insert the adapter to the rear power socket of DVR. Insert the power cable to the other side of adapter. Plug in the power cable and power on the DVR. Caution: Please use a 100~240VAC 50~60HZ and 12VDC 8A or 5A power supply or it may damage the DVR.
JPEG2000 Stand alone DVR User Guide CHAP.3 Operation 3-1 Display configuration 1.[Time] Current system time or the recorded time in playback 2.[Date] Current system date or the recorded date in playback 3.[Camera title] Camera title of the displayed channel. Camera title can be modified in [SYSTEM MENU]f[CONFIGURATION]f[CAMERA SETUP] f [CAMERA TITLE]. . 4.[Record mode] The current recording mode alarm motion continuous 5.
JPEG2000 Stand alone DVR User Guide 3-2 Screen switch/OSD position adjust Press the number button to switch to the corresponding channel for its full screen view Mode: press to switch among different split modes: 4/6/8/9/13/16 splits. +/-: button to adjust the order Adjust OSD position (High/Low): Low Position: Press “MODE”+”DOWN” at the same time High Position: Press “MODE”+”UP” at the same time Note: The OSD position returns to its default level after the DVR reboots.
JPEG2000 Stand alone DVR User Guide 3-4-2 Freeze in Full mode In full screen mode, Press FREEZE to freeze the channel, and press FREEZE again to cancel. 3-5 View in sequence Press SEQ to enter Sequential Switch and press SEQ again to cancel. Sequence order A > B > C > D …>A > B … Sequence time is adjustable in system setup. Please see [SYSTEM MENU]f [CONFIGURATION]f [INTERVAL SETUP] for details.
JPEG2000 Stand alone DVR User Guide 3-6 Zoom view Go to the channel to be zoomed and press ZOOM to enlarge to 200%, use direction buttons to move the enlarged part. Use the direction buttons to choose an area and press ENTER to zoom. Press ZOOM again to cancel 3-7 Key lock After pressing “K. LOCK “, you’ll see LOCK on screen and no button is fucntioning at this time. To unlock, press and hold K.LOCK and enter Admin’spassword. Please note that rebooting the DVR can not deactivate K.LOCK.
JPEG2000 Stand alone DVR User Guide 3-8 Record Emergency record (Red): press REC to start emgergency record at continuous record mode and at the best resolution and quality. Schedule record (Green): record at the setup schedule, record mode, resolution and quality Stop record (White): the white dot shows up when the record schedule is set to “not record” at this time.
JPEG2000 Stand alone DVR User Guide 3-9 Playback 3-9-1 Play/Stop Press PLAY key on front panel to start playback starting from the last playback time. Press“ PLAY ”during playback to choose to play forward or backward. Press“ STOP ”key to stop playback. 3-9-2 Search mode Press SEARCH key to open the search dialog window. There are 3 modes for search: SEARCH BAR, TIME/DATE, EVENT LIST. 1.[SEARCH BAR] Search by appointing a recording percentage. 2.[TIME/DATE] Search by appointing a time and date 3.
JPEG2000 Stand alone DVR User Guide 3-9-3 SEARCH BAR Using +/- keys to select the recording percentage of the search bar. Press “ ENTER ”key to confirm and start the playback. 3-9-4 TIME/DATE 1.[START] The start time and date of recording It shows that the start time and date of the recording data. 2.[END] The end time and date of recording It shows that the end time and date of the recording data. 3.[INPUT DATE/TIME] Input the appointed time and date to start playback.
JPEG2000 Stand alone DVR User Guide 3-9-6 Playback speed adjustments While playback, using the direction keys to adjust the playback speed. Speed up the playback Slow down the playback Rewind Play in forward direction The range of speed adjustment: 1/16X~1X, 1X~64X 3-9-7 Adjust Playback speed by IR remote controller While playback, select the direction keys of remote control to adjust the speed. X times high-speed playback. X times low speed playback. Rewind. Play in forward direction.
JPEG2000 Stand alone DVR User Guide CHAP.4 Set Up 4-1 Log-In 4-1-1 DVR LOG-IN Press MENU to login DVR system. Use CH. SELECTORS 1~0 to key in the password. Then press ENTER to confirm and enter the system. Erase the wrong password by PIP key. ※ Default password: ADMIN: blank (No default password. Press ENTER key directly to enter the system) Caution: 1. It is strongly suggested to change the password after the initial setup. Please keep records of your passwords.
JPEG2000 Stand alone DVR User Guide 4-2 Display setup 1.[SCREEN DISPLAY] Set up which information to be displayed at the Live and Playback mode. 2.[MONITOR SETUP] Adjust the VGA display resolution and the monitor color. 4-2-1 Screen display < LIVE > < PLAYBACK > Use cd to select an item and press ENTER to switch between ON and OFF. 1.[LIVE] Set up the following information to be displayed or not at the Live mode. TIME/DATE – Display (ON) or hide (OFF) the time and date.
JPEG2000 Stand alone DVR User Guide 4-2-2 Monitor setup 1.[VGA SETUP] Set up the VGA resolution. 2.[COLOR BAR TEST] Adjust the monitor colors by the color bar. VGA resolution setup: 1024*768/60HZ、800*600/60HZ、640*480/60HZ、 1024*768/75HZ、800*600/75HZ、640*480/75HZ Monitor colors’ adjustment by Color Bar. 4-3 Configuration 1.[HDD MANAGEMENT] Includes HDD SETUP (HDD Clear), and HDD INFORMATION. 2.[TIME/DATE SETUP] Program the system date and time. 3.
JPEG2000 Stand alone DVR User Guide 7.[BUZZER SETUP] Set the Buzzer ON or OFF at a certain condition. 8.[PASSWORD SETUP] Setup the password. 9.[SYSTEM INFORMATION] Show the system information, such as the versions of S/W and H/W, HDD model number, and CD-R model number. 4-3-1 HDD management 1.[HDD SETUP] BEGIN- Indicate the start Date/Time of recorded data on HDD (Master/Slave). RECORD- Indicate the end Date/Time of recorded data on HDD (Master/Slave).
JPEG2000 Stand alone DVR User Guide 4-3-2 Time/date setup The date and time set by the manufacturer maybe different from your time zone. It is very important to set up they system date and time before the DVR starts recording. Set the date and time by using direction buttons and [-][+] button or Jog shuttle. Date format- Asia/American/European Time format- 12 hours/24 hours Month format- English/Numeric 1.We strongly suggest completing the following settings at the initial setup.
JPEG2000 Stand alone DVR User Guide [CAMERA COLOR SETUP] Adjust the image color: Use [UP] and [DOWN] to select an item and use [-] and [+] or Jog shuttle to adjust the values. CHANNEL: Select the camera to be modified. BRIGHTNESS: Adjust image brightness (-32~31). CONTRAST: Adjust color contrast (-32~31). SATURATION: Adjust color saturation (-32~31). HUE: Adjust color hue (-32~31). [CAMERA ACTIVE SETUP] Use the direction buttons to select an item and press [ENTER] to select ON and OFF.
JPEG2000 Stand alone DVR User Guide [MOTION SETUP] 1.[CHANNEL] Select a channel for the setup. 2.[SENSITIVITY GRADE] Adjust motion detection sensitivity. 1 (LOW)~4 (VERY HIGH) 3.[MOTION DISPLAY TYPE] Setup the display type that marks the motion area. BOX- shows block / CELL- shows green lattice 4.[RECORD DURATION] The DVR record for duration from the time motion is detected. If the DVR detects motion continuosly, the DVR keeps recording through out the event, and the duration after the last motion event.
JPEG2000 Stand alone DVR User Guide 4-3-4 Interval setup 1.[SWITCH INTERVAL] FULL- Full Screen Sequence Interval setup. (Range: 1~99 SEC) PIP- Picture in Picture, the sub-picture’s sequence interval setup. (Range: 1~99 SEC) 2.[EVENT RECORD] Event Update Time is to avoid the DVR from recording the event logs from the same event. The event types include alarm, motion and video loss. When an event is triggered, it is possible that the same event keeps on being triggered for a period of time.
JPEG2000 Stand alone DVR User Guide 4-3-6 Event popup setup 1.[CHANNEL] Use [+] and [-] to select a channel. 2.[POPUP ON/OFF] Set up the POPUP function ON/OFF: Use [+] and [-] to select ON or OFF. When there is an event, the screen display will switch to a full screen of the corresponding channel. 3.[EVENT] Use [+] and [-] to select the event type that will trigger the POPUP: A- Alarm / M- Motion / AM- Alarm or Motion. 4.[DURATION] Use [+] and [-] to set up a duration of the POPUP.
JPEG2000 Stand alone DVR User Guide 4-3-8 Password setup The password consists of 1 to 8 digits. Press the number keys on the front panel to enter the password and you can use any combination of the numbers from 1 to 10. 1.[USER ID] Press e or f to set User ID. 2.[USER PW] Key in the current password. 3.[NEW PW] Key in the new password. 4.[CONFIRM PW] Enter the new password again for confirmation.
JPEG2000 Stand alone DVR User Guide 4-4 Record setup 1.[RECORD CONFIGURATION] Set up overwrite, recording mode, picture quality, resolution, and recording speed. 2.[SCHEDULE SETUP] Program the recording schedule. 3.[HOLIDAY SETUP] Set up holidays, max. 100 days. 4-4-1 Record configuration Use [UP] and [DOWN] to select an item. Use [+] and [-] to change the value. 1.[OVERWRITE] ON: When the hard drive is full, the system will overwrite the earliest recorded data.
JPEG2000 Stand alone DVR User Guide 4.[RESOLUTION] By lowering the resolution, the DVR gains the recording speed but the recorded pictures becom smaller.
JPEG2000 Stand alone DVR User Guide 4-4-2 Schedule record Program a recording schedule throught out the year. Time Cell MODE: Press MODE to select an editing mode. Use the direction keys to move the cursor, and then press [+] and [-] to select a recording mode. The editing modes are as below: TIME CELL: Program the schedule at a two-hour interval. Time Zone TIME ZONE: Program the schedule by time zone. There are 12 Time Zones in the setting.
JPEG2000 Stand alone DVR User Guide 4-4-3 Holiday setup Set up the holidays through out the year. You can program up to 100 days as holidays. The recording schedule of the holidays is the same as the settings of Sunday. Press MODE and set the editing mode as EDIT HOLIDAY. Use direction key to select and press ENTER to mark the day as a holiday. To clear the settings, press MODE to set the editing mode to CLEAR ALL DATA or CLEAR MON DATA (clear data month by month). Press ENTER to clear the settings.
JPEG2000 Stand alone DVR User Guide 4-6 External device 1.[TCP/IP SETUP] Set up the DVR’s TCP/IP information. 2.[RS232C SETUP] Set up the parameters of the RS232 port. 3.[PANTILT SETUP] Set up the parameters of the PTZ control.
JPEG2000 Stand alone DVR User Guide [IP CONFIG SETUP] Press ENTER to enter a selection. Use to move the cursor. Use [+] [-] or J.Shuttle to change the value, and press ENTER to confirm the setting and exit the selection. Use to go to another selection and repeat the previous steps. 1.[MAC ADDRESS] Indicate the DVR’s MAC address. MAC address is not editable. 2.[IP ADDRESS] Set up the DVR’s IP address. 3.[IP PORT] Set up IP Port. 4.[GATEWAY] Set up GATEWAY. 5.[SUBNET MASK] Set up SUBNET MASK. 6.
JPEG2000 Stand alone DVR User Guide [CONNECTION SETUP] Use to select and [+] [-] or J.Shuttle to change the value. 1.[TIMEOUT] Set up the remote connection response time, if the client does not receive responses from the DVR for certain duration, the client will disconnect the connection and try again. The setup range is from 1 millisecond to 12,750 seconds. 2.[RETRY COUNT] Set up the times that the client tries to reconnect to the DVR.
JPEG2000 Stand alone DVR User Guide 4-6-3 Pantilt setup < COMMAND SETUP > < SPEED SETUP > [COMMAND SETUP] Press to select and [+] / [-] to change the value. 1.[CHANNEL] Select PTZ channel. 2.[MODEL] Select PTZ protocol. 3.[PTZ ID] Select PTZ ID. 4.[BUADRATE] Select Baud Rate of PTZ control code. 5.[CMD DELAY] Set up a delay time to run the command. 6.[COMMAND] Pick up PTZ CMD. 7.[LENGTH] Set up the length of PTZ control code. 8.[CODE] The control code of PTZ CMD. Please refer to CHAP.
JPEG2000 Stand alone DVR User Guide [SPEED SETUP] Press to select and [+] / [-] to change the value. 1.[PAN SPEED] Set the PANing speed. 2.[TILT SPEED] Set the TILTing speed. 3.[ZOOM SPEED] Set the speed of ZOOM IN/OUT. 4.[FOCUS SPEED] Set the speed of FOCUS NEAR/FAR. 4-7 Factory default Press to select and ENTER to turn ON and OFF the selection. Move the cursor to RUN and press ENTER to execute the Factory Default. 1.[ALL] Set all the settings back to factory default. 2.
JPEG2000 Stand alone DVR User Guide CHAP.5 CD-R Back-up 5-1 Data backup 1.[HDD] Indicate the start and the end recording date and time of the HDD(s). 2.[CD-R] Select a starting date and time for backup. Press ENTER and use ef to move the cursor. Use [+] [-] or J.Shuttle to change the value. Press ENTER and then d to go to SIZE to choose a backup size. 3.[SIZE] Insert a blank CD disk and the DVR will check the disk size. Press ENTER to choose a backup size. Use [+] [-] or J.Shuttle to change thevalue.
JPEG2000 Stand alone DVR User Guide 5-2 CD Player software installation 1.Insert software CD. 2. Click [Install CD-R backup player] to start the installation. 3. Select a Destination Folder 4. Copy files to the Destination Folder. System will build a new icon of [CD BACKUP PLAYER] on PC [DESKTOP]. Double click the icon of CD Backup Player from Desktop to run the program.
JPEG2000 Stand alone DVR User Guide 5-3 CD Player software interface 1.Display screen: To display the backup image 2.Time display: To indicate the current time 3.Information window: To indicate the CD’s start/end time and date, and the backup video quality (resolution). 4.Speed Adjustment: Speed: Select a playback speed (2X, 4X, 8X,16X, 32X, 64X) and press for Fast Rewind and Fast Forward Delay: Select a speed to play in slow motion (1/2X, 1/4, 1/8X, 1/16X) and press 5. 6.
JPEG2000 Stand alone DVR User Guide Open AJP file 1. Select (OPEN) and the window below will show up on the screen. 2. Select the file and click [OPEN] to open the AJP file. Save JPG file 1. During playback and under FULL SCREEN MODE, when you see the picture you want to save, click EDIT. 2. Select [SAVE] to save the picture as JPEG file or select [PRINT] to print the image. To save single picture as JPG file. To print the picture. To exit the EDIT mode.
JPEG2000 Stand alone DVR User Guide CHAP.6 PTZ camera control 6-1 PTZ camera Installation 6-1-1 Connection Setup Connect the PTZ’s D+ to the DVR’s D+, and D- to D-. 6-1-2 PTZ setup Each PTZ manufacturer may have different transmission buad rate. Please refer to the PTZ manuals for the detail information. Enter the baud rate suggested by the manufacturer in the DVR’s PTZ setup. [EXTERNAL DEVICE] SYSTEM MENU ` EXTERNAL DEVICE ` PANTILT SETUP ` COMMAND SETUP 1. [MODEL]: select a PTZ protocol. 2.
JPEG2000 Stand alone DVR User Guide 6-2 PTZ camera operation Use MENU and NEXT key to select a PTZ command, and [+] [-] to select the channel. Then, press PTZ key to enter the PTZ control mode. Indicate the channel connected with a PTZ camera. Indicate PTZ command, press ENTER to send control code by PTZ key. You can also press the PTZ button on the front panel, and use the front panel pre-assigned PTZ function keys to control the PTZ camera.
JPEG2000 Stand alone DVR User Guide CHAP.7 Network and client software 7-1 Network Introduction Users have to indentify what kind of Internet access they have before they set up the DVR’s network parameters. DSL and cable modem are the most popular broadband technologies. ADSL- Asymmetric Digital Subscriber Line ADSL is one of xDSL technologies, transmitting digital data over the wires of a local telephone network.
JPEG2000 Stand alone DVR User Guide 7-2-2 Via ADSL First, identiry if you have Static IP or Dynamic IP service. If you do not know, ask your ISP (Internet Service Provider). If you have Static IP, your ISP should provide you a static IP address, which will never change even when you reboot your modem. [Via ADSL with Static IP address] Connect the Network cable of Cable Modem output to DVR Enter [SYSTEM MENU]f [EXTERNAL DEVICE] f [TP/IP SETUP]f [IP CONFIG SETUP].
JPEG2000 Stand alone DVR User Guide [Via ADSL with Dynamic IP] If you have ADSL with Dynamic IP address, the network administrator assigns you an IP address from their pool when you or your ISP reboots the network and you may get a different IP address from time to time. If you are using ADSL service with Dynamic IP, you must add a Router in the network system, unless your DSL MODEM has a built-in Router.
JPEG2000 Stand alone DVR User Guide 7-3 Router setup There is a wide selection of routers in the market. They may be very different in terms of configuration and operation. Here is an example of how to set up a router. For details, please read your router’s manual. First, connect a computer to the router for configuration. In this example, the DVR’s IP is set to 192.168.1.53 and its port number is 8000. The router model is PCI BLW-04G. Enter the router’s setup and select Static IP or PPPoE. 1.
JPEG2000 Stand alone DVR User Guide [PPPoE setup] Select PPPoE in WAN connection Type Enter User Name and Passward provided by your ISP The router will get the IP address upon connection. In this example, we get the IP address of 211.20.82.39. 2. [Virtual server setup] Enter Virtual Server setup. Enter DVR’s IP (192.168.1.53) and port number (8000). Enable the port and check both protocols of TCP and UDP. Save the settings before leaving this page.
JPEG2000 Stand alone DVR User Guide 7-4 Client software 7-4-1 Install and setup Insert the Install CD into CD-ROM, and the computer will auto-run the Install program. We suggest installing the software on Windows XP or Windows 2000. 1.[Install Client software] Click [Install Client software]. 7-4-2 Install Client software Select a Destination Folder. When finished, the software will create a shortcut on the desktop. Click the shortcut to run the client software.
JPEG2000 Stand alone DVR User Guide 7-4-3 Software operation [Remote viewer interface] 1.[Live Display] Remote DVR Live display 2.[Current Status ] To show the current status 3.[PTZ Camera Control ] To control PTZ Camera Zoom/Focus/Direction ※ Remote Control of PTZ: 1) Set up PTZ at DVR first 2) Set up PTZ from the Client Software 4.[Screen Split ] To select Full/4/9/16 split screen display 5.[Channel Selection ] To select CAM1~16 when full or split screen display 6.
JPEG2000 Stand alone DVR User Guide 7-4-4 Client software setup [IP/PORT] 1.[DVR NAME] Enter the DVR’s location or name 2.[IP LIST] Show the list of saved DVR IP addresses. If you are connecting to a DVR in this list, you can simply click it from the list, enter the DVR Admin’s password, and press SAVE and then OK. Click CONNECT from Remote Viewer Interface to connect. 3.
JPEG2000 Stand alone DVR User Guide [DDNS] 1.[Group] Enter Group name registered on DDNS Server. Please refer to 7-5 DDNS setup and operation for details. 2.[DVR Name] Enter DVR name registered on DDNS Server. If the DVR name is entered and saved before, click LOAD to browse the list. 3.[Save/Load] Save: Save the setup into the DDNS list Load: Open the DDNS list. . Please see the following illustration [DDNS LIST] for details. 4.[IP Address] Show DVR’s current IP address and Port number. 5.
JPEG2000 Stand alone DVR User Guide [PTZ/SAVE] 1.[Circular Monitoring Interval] Set up a sequential switch interval. 2.[Scan Rate] Select a Fast forward (FF) speed of remote Playback. 3.[PTZ Type] Select the protocol used by your PTZ camera. 4.[PTZ Baudrate] Select a PTZ camera buad rate. 5.[Set Path to Save Reorded Images] Set a path to save the video clips. If you do not specify a path, the program will save all files to its default location, C:\Program Files\Remote_J2K. 6.
JPEG2000 Stand alone DVR User Guide 7-4-6 Remote playback When the DVR is connected, click [PLAYBACK] to enter Playback interface. [Remote Playback Interface] 1.[Playback Picture] To show the playback video 2.[Time/Date Selection] To select time/date of playback 3.[Record and Playback Status] START – To show the record START Time/Date END – To show the record END Time/Date REQUEST – To show the record DISPLAY Time/Date 4.[Screen Split] To select Full/4/9/16 split screen display 5.
JPEG2000 Stand alone DVR User Guide [Search button] 1. Fast Reward (RW) 2. Fast Forward (FF) 3. RW (Speed 1X) 4. Stop / Pause 5. Playback (Speed 1X) 6. Go to the beginning of recording 7. Jump to the previous hour 8. Jump to the next hour 9. Go to the end of recording [Remote Playback Operation] Drag the mouse over the time bar to select a playback time. Select a Year/Month/Day to playack.
JPEG2000 Stand alone DVR User Guide 7-4-7 Back up via Client software Save the recorded data as single JPEG picture or AVI format. [Save the recorded data as single JPEG picture] Press “STOP” right before where you want to save and press “SAVE”. The picture will be saved to the assigned path which you set up in 7-4-4 [Remote software setup] f [PTZ/SAVE] [print the recorded data] Press “STOP” and “PRINT” to print out the picture.
JPEG2000 Stand alone DVR User Guide 7-5 DDNS setup and operation DDNS SERVER setup 1. Connect to DDNS SERVER(http://advr.com.tw or http://59.124.143.151) by IE browser Select [REGISTER] to register a new account 2. Add a new account Group: Add a new user name User Password: Add user password Confirm Password: Confirm the password E-mail: Add an Email address for the password reminders 3. Enter group name and password to LOGIN DDNS function.
JPEG2000 Stand alone DVR User Guide 4. Select “ADD DVR” to add DVR information 5. Add DVR information: DVR NAME: Set a DVR name MAC ADDRESS: Enter the DVR’s MAC address. DVR’s MAC address can be found in DVR’s [SYSTEM MENU] f [EXTERNAL DEVICE]f[TCP/IP SETUP]f[IP CONFIG SETUP] IP: Enter the DVR’s current IP address PORT: Enter the DVR’s port number ※It is required to enter DVR NAME and MAC ADDRESS. DVR’s IP and PORT number can be left blank.. Press [OK] to save the settings 6.
JPEG2000 Stand alone DVR User Guide DVR setup 1. The DVR setup is a onetime effort. First, make sure your DVR can be accessed over the Internet. Please refer to 7-2 Network installation and setup for details. 2. Go to [SYSTEM MENU]f[ [EXTERNAL DEVICE]f[TCP/IP SETUP] f[DDNS SETUP] DDNS ON/OFF: Press ENTER to turn ON the DDNS service. DNS SERVER: Enter the DDNS Server IP address. INTERVAL: Set an interval for the DVR to auto-update its IP address to DDNS server.
JPEG2000 Stand alone DVR User Guide B 2. Select DDNS in [IP/PORT] setup 3.Go to DDNS setup [DDNS INFO] GROUP: Enter Group nameregistered on DDNS Server. DVR NAME: Enter DVR name registered on DDNS Server. If the DVR name is entered and saved before, click LOAD to browse the list. Save/Load: Save: Save the setup into the DDNS list. Load: Open the DDNS list. [DVR INFO] Get IP: Click “Get IP” to get the current DVR IP address and port number from DDNS server.
JPEG2000 Stand alone DVR User Guide Configuration of DDNS connection 1. DVR connect to DDNS server automatically and update the IP address by itself. 2. The client accessesto DDNS server and requests IP address from DDNS server. 3. DDNS server replies the DVR’s IP address and port number. 4. Client PC connects to DVR.
JPEG2000 Stand alone DVR User Guide Users can also access to the DVR from Internet Explore for remote viewing, remote backup, and playback the backup file. Log on to DDNS server and go to the DVR List Remote Live View via IE Browser Click WEB to link to your DVR 1.[Live picture] Shows the live pictures of DVR 2.[DVR info] IP: Indicate the IP address of DVR PORT: Indicate the PORT of DVR ID: Use ADMIN PW: Enter the ADMIN’s password 3.
JPEG2000 Stand alone DVR User Guide PTZ: Select the protocol BAUDRATE: Select the baud rate CH: Select the ID of PEZ camera ZOOM: Zoom in/out FOCUS: Focus near/far IRIS: IRIS open/close Web Network Backup Click “Backup” to open the web page “Web Network Backup” 1.
JPEG2000 Stand alone DVR User Guide 2. Function setup: Connect Test: To test the connection status Unlock: To get the record start/End time of DVR Set Backup Time: Set the start/end time, size and path of file backup Start Backup: Active the backup function 3. The information of DVR Server: Recorded Start Time: Indicate the recorded start time Recorded End Time: Indicate the recorded end time Update: Update the recorded time 4.
JPEG2000 Stand alone DVR User Guide Play backup file Click [Backup Player] to open the web page of “Backup Player” 1. Display the backup image 2. Indicate the present time of monitoring 3. Indicate the start/end time of backup file 4. Switch to the different modes of multi-screen 5. Channel selection: Ch1~Ch16 6. SPEED: Adjust the speed of fast forward DELAY: Adjust the speed of reward 7.
JPEG2000 Stand alone DVR User Guide 8. Function keys: OPEN: Open the backup file EDIT: Edit the backup image AVI SAVE: To save the AVI file EXIT: Log out the program 9. audio options: ON: To start the audio function Ch1~4: to select the channel with audio Save AVI file: 1. Click to open the backup file and select 2. Click to open the AVI SAVE function 3.
JPEG2000 Stand alone DVR User Guide Appendix.1 Record time table [4ch DVR] ※The numbers are for reference only.
JPEG2000 Stand alone DVR User Guide [8/16ch DVR] ※The numbers are for reference only.
JPEG2000 Stand alone DVR User Guide Appendix.
JPEG2000 Stand alone DVR User Guide Appendix.3 Firmware upgrade Install USB driver 1. Connect USB port between PC and DVR 2. Press and hold Search and Play keys on front panel and power on DVR 3. The DVR beeps for a moment. 4. When the Windows system detect new device, please select [Install from a list or specific location] 5. Select the location of USB driver 6. A warning message pop up while the driver is installing. Please select “Continue Anyway”.
JPEG2000 Stand alone DVR User Guide 7. Start to copy the driver to Windows system. 8. After installation, the USB device [BulkUsb.Sys Usb Bulk I/O Driver] can be found from [Device Manager].
JPEG2000 Stand alone DVR User Guide Install USB upgrade program Insert the Install CD 1.Please select :[Install USB upgrade program(Allupdate) 2. Set up Directory (default Directory : "C:\Program Files\J2000\Allupdate\") After installation, there’ll be a shortcut on desktop. Click on it for remote viewing.
JPEG2000 Stand alone DVR User Guide Upgrade firmware Update procedures Start Start to update Update Boot Step 1 update BOOT Update F/W Step 2 update F/W Finish Finish the update procedures Step 1、Update BOOT 1. Connect the USB port between DVR and PC. (Do not power on DVR in advance) 2. Execute USB update program AUDTOTAL,select “Boot” then choose the file: _FBoot_0000_16M_V2.04.bin 3. Press and hold SEARCH and PLAY and power on the DVR. 4.
JPEG2000 Stand alone DVR User Guide Step 2、Update F/W 1. Select ALLUPDATE then choose the file: _ALLUPDATE_4J_NTIC_noboot_V1.3.bin 2. Press and hold SEARCH and PLAY and power on the DVR 3. When the DVR is turned on, you will hear very short beeps. Keep holding the “SEARCH” and “PLAY” buttons. When the beeps turn slow and the “Send” icon of the program, J2000 USB Downloader, becomes active, release the buttons. 4. Click “SEND” to transmit the files.
JPEG2000 Stand alone DVR User Guide Appendix.4 Play only mode Introduction PLAY ONLY MODE can be used in the following situations: When you need to playback a hard drive from another DVR When you need to playback the video which you deleted by running HDD CLEAR Enter “PLAY ONLY MODE” Turn on the DVR. At the initial screen that says HDD DETECT, press [PLAY] and System enters “PLAY ONLY MODE”. To exit PLAY ONLY MODE, reboot the DVR and DO NOT press PLAY at the initial screen. Under PLAY ONLY MODE: 1.