Instruction Manual
Table Of Contents
- 1 Safety summary
- 2 Switch Names and Functions
- 3 Operation
- 4 Icon Description
- 5 Function Menu
- 5.1 Simple Timer Setting
- 5.2 Operation Schedule Setting
- 5.3 Power Savings Setting
- 5.4 Night Quiet Operation
- 5.5 Power Saving/Night Quiet Schedule Setting
- 5.6 Power Consumption Display
- 5.7 Autoboost (QUICK MODE) Setting
- 5.8 Comfort Setting
- 5.9 Motion sensor setting
- 5.10 Setback Setting
- 5.11 Elevating Grille
- 5.12 Filter Reminder Reset Setting
- 5.13 FrostWash
- 5.14 Individual Louver Setting
- 5.15 Cancel Individual Louver Setting
- 5.16 Louver Open/Close
- 5.17 Ventilation
- 5.18 Total Heat Exchanger Setting
- 6 Service & installation menu
- 6.1 Installation menu
- 6.1.1 Test Run
- 6.1.2 Function selection
- 6.1.3 Thermistor Selection
- 6.1.4 Input / Output Setting
- 6.1.5 Thermistor Calibration in Controller
- 6.1.6 Fan Speed at Cooling Thermo-OFF
- 6.1.7 Fan Speed at Heating Thermo-OFF
- 6.1.8 Indoor Unit Address Change
- 6.1.9 Address Check Operation
- 6.1.10 Address Initialization
- 6.1.11 Setting Initialization
- 6.1.12 Main Remote Setting
- 6.1.13 Priority Setting
- 6.1.14 Cancel Preheating Control
- 6.1.15 Elevating grille Setting
- 6.1.16 Power Up Setting
- 6.1.17 Setback Trigger Unit
- 6.1.18 Refrigerant Leak Sensor Setting
- 6.2 Service menu
- 6.3 Check Menu
- 6.1 Installation menu
- 7 Screen Display Setting menu
- 8 Contact Information menu
- 9 Hotel Mode Setting
- 10 In Alarm Condition
5.2.4 Reset the setting
1 Select “Operation Schedule” on the “Function Menu” screen
and press “OK”.
• If the current time is not set, the “Adjusting Date/Time”
setting screen is displayed.
• This menu to reset the schedules is available only if some
settings have been done.
2 Press “ ” or “ ” to select “Reset All” and then press “OK”.
3 Select "Yes" by pressing “ ” or “ ”and then press "OK".
All schedule and holiday settings are reset and the screen
returns to the Step 3 of
“5.2.1 Schedule Day and Time
Setting”
.
5.3 POWER SAVINGS SETTING
No. Item Description
Capacity Control
Limits the heating and cooling capacity
of the outdoor unit in order to reduce the
running current of the system to match with
the capacity control setting.
Set control mode and power savings level
with its corresponding value.
Rotation Control
Interlock with indoor units of the same
outdoor unit system and switch to FAN
operation in sequence.
Set control mode and fan mode time.
Intermittent
Control
Cooling/heating mode and fan mode are
repeated at regular intervals.
Set power savings level.
No Setting Power savings operation is not performed.
? NOTE
• For detailed capacity control settings information refer to
“6.2.4 Power
Saving Details Setting” in this manual.
• The power savings mode that can be switched differs depending on
the type of the outdoor unit or indoor unit.
• The power savings modes that can be switched according to the
"Main / Sub" display are as follows.
- Main — the power savings mode can be switched from
to .
- Sub — the power savings mode cannot be switched. The power
savings mode of the sub synchronizes with that of the main
remote controller of the same outdoor unit system.
• When the power savings mode is "Indoor rotation control", the power
savings level cannot be changed.
• When the power savings mode is "No Setting", the power savings ON
/ OFF and power savings level cannot be changed.
• When the power savings mode is "Outdoor capacity control" and
sub, the power savings ON / OFF and power savings level cannot
be changed.
• When the power savings mode is switched, power savings ON / OFF
is set to OFF.
• When using the power savings function, the cooling and heating
capacity may decrease.
• Detailed settings can be changed from the power saving details
setting.
EN
FUNCTION MENU
PMML0601 rev.0 - 07/202213