Instruction Manual
Table Of Contents
- 1 Safety summary
- 2 Switch Names and Functions
- 3 Operation
- 4 Icon Description
- 5 Function Menu
- 5.1 Simple Timer Setting
- 5.2 Operation Schedule Setting
- 5.3 Power Savings Setting
- 5.4 Night Quiet Operation
- 5.5 Power Saving/Night Quiet Schedule Setting
- 5.6 Power Consumption Display
- 5.7 Autoboost (QUICK MODE) Setting
- 5.8 Comfort Setting
- 5.9 Motion sensor setting
- 5.10 Setback Setting
- 5.11 Elevating Grille
- 5.12 Filter Reminder Reset Setting
- 5.13 FrostWash
- 5.14 Individual Louver Setting
- 5.15 Cancel Individual Louver Setting
- 5.16 Louver Open/Close
- 5.17 Ventilation
- 5.18 Total Heat Exchanger Setting
- 6 Service & installation menu
- 6.1 Installation menu
- 6.1.1 Test Run
- 6.1.2 Function selection
- 6.1.3 Thermistor Selection
- 6.1.4 Input / Output Setting
- 6.1.5 Thermistor Calibration in Controller
- 6.1.6 Fan Speed at Cooling Thermo-OFF
- 6.1.7 Fan Speed at Heating Thermo-OFF
- 6.1.8 Indoor Unit Address Change
- 6.1.9 Address Check Operation
- 6.1.10 Address Initialization
- 6.1.11 Setting Initialization
- 6.1.12 Main Remote Setting
- 6.1.13 Priority Setting
- 6.1.14 Cancel Preheating Control
- 6.1.15 Elevating grille Setting
- 6.1.16 Power Up Setting
- 6.1.17 Setback Trigger Unit
- 6.1.18 Refrigerant Leak Sensor Setting
- 6.2 Service menu
- 6.3 Check Menu
- 6.1 Installation menu
- 7 Screen Display Setting menu
- 8 Contact Information menu
- 9 Hotel Mode Setting
- 10 In Alarm Condition
5.5.1 Schedule Day and Time Setting
? NOTE
indicates that schedule control is not possible. Refer to “7.1 Adjusting
date / time” to set the date and time.
Set the schedule day and time
1 Select “Power Saving/Night Quiet Schedule” on the
“Function Menu” screen and press “OK”.
• If the sub remote controller or indoor unit does not support
power savings, the power saving schedule setting screen for
intermittent control (Step3) is displayed.
2 Press “ ” or “ ” to select the setting items, and then press
“OK”. The items are changed as follows:
"Capacity Control" ↔ "Intermittent" ↔ "Night Quiet Operation".
• If the current time is not set, the “Adjusting Date/Time”
setting screen is displayed.
• If no schedule or holiday has been set, Step4 is displayed.
3 Press “ ” or “ ” to select the schedule day and time settings,
and then press “OK”.
4 Select the day of the week (from Mon. to Sun.) to be set with
“
” or “ ”, and press “OK”.
•
(run) and (stop) is displayed on the LCD.
• To copy the setting contents of the previous day, press “
”
and “OK” simultaneously.
5 Press” ” or “ ” to select schedule timer No. 1 to No.5, and
press “
” or “ ” to select “ON Time” ↔ “OFF Time” ↔ “Noise
Reduction”↔ “
”. By pressing “ ” or “ ”, “ON / OFF Time”
and “Noise Reduction” can be set.
• Press and hold " " or " " to increase or decrease
continuously.
• Five different schedule timers (maximum) can be set for
each day of the week.
• Press “OK” to display the schedule time setting screen for
the next day of the week.
• Select “
” and press “OK” to delete the setting of “ON /
OFF Time” and “Noise Reduction”.
• Press “
” to return to Step4.
Indicates that schedule control is in operation.
EN
FUNCTION MENU
PMML0601 rev.0 - 07/202217