Instruction Manual
Table Of Contents
- 1 Safety summary
- 2 Switch Names and Functions
- 3 Operation
- 4 Icon Description
- 5 Function Menu
- 5.1 Simple Timer Setting
- 5.2 Operation Schedule Setting
- 5.3 Power Savings Setting
- 5.4 Night Quiet Operation
- 5.5 Power Saving/Night Quiet Schedule Setting
- 5.6 Power Consumption Display
- 5.7 Autoboost (QUICK MODE) Setting
- 5.8 Comfort Setting
- 5.9 Motion sensor setting
- 5.10 Setback Setting
- 5.11 Elevating Grille
- 5.12 Filter Reminder Reset Setting
- 5.13 FrostWash
- 5.14 Individual Louver Setting
- 5.15 Cancel Individual Louver Setting
- 5.16 Louver Open/Close
- 5.17 Ventilation
- 5.18 Total Heat Exchanger Setting
- 6 Service & installation menu
- 6.1 Installation menu
- 6.1.1 Test Run
- 6.1.2 Function selection
- 6.1.3 Thermistor Selection
- 6.1.4 Input / Output Setting
- 6.1.5 Thermistor Calibration in Controller
- 6.1.6 Fan Speed at Cooling Thermo-OFF
- 6.1.7 Fan Speed at Heating Thermo-OFF
- 6.1.8 Indoor Unit Address Change
- 6.1.9 Address Check Operation
- 6.1.10 Address Initialization
- 6.1.11 Setting Initialization
- 6.1.12 Main Remote Setting
- 6.1.13 Priority Setting
- 6.1.14 Cancel Preheating Control
- 6.1.15 Elevating grille Setting
- 6.1.16 Power Up Setting
- 6.1.17 Setback Trigger Unit
- 6.1.18 Refrigerant Leak Sensor Setting
- 6.2 Service menu
- 6.3 Check Menu
- 6.1 Installation menu
- 7 Screen Display Setting menu
- 8 Contact Information menu
- 9 Hotel Mode Setting
- 10 In Alarm Condition
5.6 POWER CONSUMPTION DISPLAY
This function displays the power consumption of the outdoor unit
compressor.
The value of each displayed in Graph/List format is 1 day
(24h (- every 2 hrs.)), 1 week (7 days), and 1 year (12 months).
? NOTE
• The numerical value is a reference. Do not use this unit for the following:
calculation of power rates, examination of the power contract, or
calculation of greenhouse gas emissions.
• This cannot be set if the power savings function is not supported.
• In following instances, the calculated value may be a decit or may
be changed.
- Power Failure (outdoor unit, indoor unit, wired controller)
- Communication Failure (outdoor unit ↔ indoor unit ↔ wired
controller)
- Modication of time
•
indicates that schedule control is not possible. Refer to
“7.1 Adjusting date / time” to set the date and time.
Set power consumption display
1 Select “Power Consumption Display” on the “Function Menu”
screen and press “OK”.
• If the current time is not set, the “Adjusting Date/Time”
setting screen is displayed.
2 Press “OK”.
3 Press “ ” or “ ” to select the display period, and then press
“OK”.
It switches in the order of 1 day (24 hours) ↔ 1 week
(7 days) ↔ 1 year (12 months).
• Comparison
Press “
” or “ ” to switch the comparison target for the display
period.
2 days before / 1 day before ↔ 1 day before / Today
2 week ago / 1 week ago↔ 1 week ago / This week
2 years ago / 1 year ago ↔ 1 year ago / This year
• Display scale
Press “
” or “ ” to switch the display scale.
• Graph ↔ List display
Press "OK" to switch between the graph and list display of
the power consumption display.
• Press “
” to return to the display period selection screen.
EN
FUNCTION MENU
PMML0601 rev.0 - 07/202219