Instruction Manual
Table Of Contents
- 1 Safety summary
- 2 Switch Names and Functions
- 3 Operation
- 4 Icon Description
- 5 Function Menu
- 5.1 Simple Timer Setting
- 5.2 Operation Schedule Setting
- 5.3 Power Savings Setting
- 5.4 Night Quiet Operation
- 5.5 Power Saving/Night Quiet Schedule Setting
- 5.6 Power Consumption Display
- 5.7 Autoboost (QUICK MODE) Setting
- 5.8 Comfort Setting
- 5.9 Motion sensor setting
- 5.10 Setback Setting
- 5.11 Elevating Grille
- 5.12 Filter Reminder Reset Setting
- 5.13 FrostWash
- 5.14 Individual Louver Setting
- 5.15 Cancel Individual Louver Setting
- 5.16 Louver Open/Close
- 5.17 Ventilation
- 5.18 Total Heat Exchanger Setting
- 6 Service & installation menu
- 6.1 Installation menu
- 6.1.1 Test Run
- 6.1.2 Function selection
- 6.1.3 Thermistor Selection
- 6.1.4 Input / Output Setting
- 6.1.5 Thermistor Calibration in Controller
- 6.1.6 Fan Speed at Cooling Thermo-OFF
- 6.1.7 Fan Speed at Heating Thermo-OFF
- 6.1.8 Indoor Unit Address Change
- 6.1.9 Address Check Operation
- 6.1.10 Address Initialization
- 6.1.11 Setting Initialization
- 6.1.12 Main Remote Setting
- 6.1.13 Priority Setting
- 6.1.14 Cancel Preheating Control
- 6.1.15 Elevating grille Setting
- 6.1.16 Power Up Setting
- 6.1.17 Setback Trigger Unit
- 6.1.18 Refrigerant Leak Sensor Setting
- 6.2 Service menu
- 6.3 Check Menu
- 6.1 Installation menu
- 7 Screen Display Setting menu
- 8 Contact Information menu
- 9 Hotel Mode Setting
- 10 In Alarm Condition
5.14 INDIVIDUAL LOUVER SETTING
This function is to individually set the air direction of multiple air
outlets.
? NOTE
• This function is available when the indoor unit supports individual
louvers.
• It cannot be set while the air conditioner is stopped.
• The fan speed changes to "LOW" while this function is being set. After
the setting is completed, the unit operation is back to normal.
• As for "Start-up of Heating Operation", "During Defrost Operation"
and "Activation of Thermo-Controller", all the louver angles are
automatically secured horizontally when this function is activated.
• This function is not available if two remote controllers (including a
combination of wired controller + wireless controller) are used.
1 Select “Individual Louver Setting” on the “Function Menu”
and press “OK”.
2 Select “Individual Louver Setting” and press “OK”.
? NOTE
If there is one indoor unit connected with the controller, Step4 is displayed.
3 Press” ”, “ ”, “ ”, or “ ” to select the indoor unit to change
the louver direction, and press “OK”.
? NOTE
The indoor unit displayed on the screen ashes if an individual louver is
set.
4 Press “ ” or “ ” and select the louver from 1 to 4.
The selected louver is opened while the unselected louvers
are closed.
5 Press” ” or “ ” to select the louver angle and press "OK".
Return to Step3.
The louver angle is changed as follows.
SwingIndv. Indv. Indv. Indv. Indv. Indv. Indv. Indv.
6 Ensure that individual "Indv." is turned on at the Louver on
the home screen.
FUNCTION MENU
PMML0601 rev.0 - 07/202234