Instruction Manual
Table Of Contents
- 1 Safety summary
- 2 Switch Names and Functions
- 3 Operation
- 4 Icon Description
- 5 Function Menu
- 5.1 Simple Timer Setting
- 5.2 Operation Schedule Setting
- 5.3 Power Savings Setting
- 5.4 Night Quiet Operation
- 5.5 Power Saving/Night Quiet Schedule Setting
- 5.6 Power Consumption Display
- 5.7 Autoboost (QUICK MODE) Setting
- 5.8 Comfort Setting
- 5.9 Motion sensor setting
- 5.10 Setback Setting
- 5.11 Elevating Grille
- 5.12 Filter Reminder Reset Setting
- 5.13 FrostWash
- 5.14 Individual Louver Setting
- 5.15 Cancel Individual Louver Setting
- 5.16 Louver Open/Close
- 5.17 Ventilation
- 5.18 Total Heat Exchanger Setting
- 6 Service & installation menu
- 6.1 Installation menu
- 6.1.1 Test Run
- 6.1.2 Function selection
- 6.1.3 Thermistor Selection
- 6.1.4 Input / Output Setting
- 6.1.5 Thermistor Calibration in Controller
- 6.1.6 Fan Speed at Cooling Thermo-OFF
- 6.1.7 Fan Speed at Heating Thermo-OFF
- 6.1.8 Indoor Unit Address Change
- 6.1.9 Address Check Operation
- 6.1.10 Address Initialization
- 6.1.11 Setting Initialization
- 6.1.12 Main Remote Setting
- 6.1.13 Priority Setting
- 6.1.14 Cancel Preheating Control
- 6.1.15 Elevating grille Setting
- 6.1.16 Power Up Setting
- 6.1.17 Setback Trigger Unit
- 6.1.18 Refrigerant Leak Sensor Setting
- 6.2 Service menu
- 6.3 Check Menu
- 6.1 Installation menu
- 7 Screen Display Setting menu
- 8 Contact Information menu
- 9 Hotel Mode Setting
- 10 In Alarm Condition
6.2.5 Temperature Range Restriction
The temperature range can be set by operating the remote
controller.
1 Select “Service Menu” on the Service & Installation screen
and press “OK”.
2 Select “Temperature Range Restriction” and press “OK”.
3 Select “Lower Limit for Cooling Operation” or “Upper Limit for
Heating Operation” and press “OK”.
4 Press “
”, “ ”, “ ”, or “ ” to select the setting value and
press”OK”.
5 Press “
” to return to Step3.
? NOTE
Settable temperature range varies depending on the type of indoor unit
or outdoor unit.
6.2.6 Dual setpoint setting
When Auto Cool/Heat operation mode is selected, this function
can be used to set specic temperature set point for cooling
operation mode and for heating operation mode.
To use this function, Auto Cool/Heat operation mode shall be
activated on the wired remote controller. Refer to the optional
parameter b8 in the function selection menu for details.
1 Select “Service Menu” on the Service & Installation screen
and press “OK”.
2 Select “Dual Setpoint” and press “OK”.
3 Press “
” or “ ” to select “ON” or “OFF”.
4 Press “OK” to conrm the setting.
5 Press “
” to return to Step2.
6.2.7 Main/Sub Display Setting
The display of the main / sub setting of the remote controller can
be deactivated from this menu.
1 Select “Service Menu” on the Service & Installation screen
and press “OK”.
2 Select “Main/Sub Display” and press “OK”.
3 Press “
”, “ ”, “ ”, or “ ” to select “Not Display”.
4 Press “OK” to conrm the setting.
5 Press “
” to return to Step2.
With Priority Setting Without Priority Setting
Main
No icon
Sub
SERVICE & INSTALLATION MENU
PMML0601 rev.0 - 07/202278