Model Modèle Modelo DH 24PF Rotary Hammer Marteau rotatif Martillo perforador INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS WARNING Improper and unsafe use of this power tool can result in death or serious bodily injury! This manual contains important information about product safety. Please read and understand this manual before operating the power tool. Please keep this manual available for others before they use the power tool.
English CONTENTS Page IMPORTANT SAFETY INFORMATION ........ 3 MEANINGS OF SIGNAL WORDS .......... 3 SAFETY ................................................... 4 GENERAL SAFETY RULES ................. 4 SPECIFIC SAFETY RULES AND SYMBOLS ..... 6 DOUBLE INSULATION FOR SAFER OPERATION ..................................... 8 FUNCTIONAL DESCRIPTION ................ 9 NAME OF PARTS ................................ 9 SPECIFICATIONS ................................ 9 Français MAINTENANCE AND INSPECTION ....
English IMPORTANT SAFETY INFORMATION Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power tool. Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures.
English SAFETY GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS 1. Work Area (1) Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. (2) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
English (3) Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. (4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. (5) Do not overreach. Keep proper footing and balance at all times.
English SPECIFIC SAFETY RULES AND SYMBOLS 1. 2. Hold tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. ALWAYS wear ear protectors when using the tool for extended periods. Prolonged exposure to high intensity noise can cause hearing loss. 3. NEVER touch the tool bit with bare hands after operation. 4.
English 14. Keep motor air vent clean. The tool’s motor air vent must be kept clean so that air can freely flow at all times. Check for dust build-up frequently. 15. Operate power tools at the rated voltage. Operate the power tool at voltages specified on its nameplate. If using the power tool at a higher voltage than the rated voltage, it will result in abnormally fast motor revolution and may damage the unit and the motor may burn out. 16. NEVER use a tool which is defective or operating abnormally.
English DOUBLE INSULATION FOR SAFER OPERATION To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. “Double insulation” means that two physically separated insulation systems have been used to insulate the electrically conductive materials connected to the power supply from the outer frame handled by the operator. Therefore, either the symbol “ ” or the words “Double insulation” appear on the power tool or on the nameplate.
English FUNCTIONAL DESCRIPTION NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safey instructions contained in this manual. Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own power tool.
English ASSEMBLY AND OPERATION APPLICATIONS Rotation and hammering function 䡬 Drilling anchor holes 䡬 Drilling holes in concrete 䡬 Drilling holes in tile Rotation only function 䡬 Drilling in steel or wood (with optional accessories) 䡬 Tightening machine screws, wood screws (with optional accessories) Hammering only function 䡬 Light-duty chiselling of concrete, groove digging and edging PRIOR TO OPERATION 1.
English 6. Mounting the drill bit (Fig. 2) Front cap Grip Part of SDS-plus shank CAUTION: To prevent accidents, make sure to turn the switch off and disconnect the plug from the receptacle. NOTE: Drill bit When using tools such as bull points, Fig. 2 drill bits, etc., make sure to use the genuine parts designated by our company. (1) Clean the shank portion of the drill bit. (2) Insert the drill bit in a twisting manner into the tool holder until it latches itself. (Fig.
English CAUTION: 䡬 The dust cup and dust collector (B) are for exclusive use of concrete drilling work. Do not use them for wood or metal drilling work. 䡬 Insert dust collector (B) completely into the chuck part of the main unit. 䡬 When turning the rotary hammer on while dust collector (B) is detached from a concrete surface, dust collector (B) will rotate together with the drill bit. Make sure to turn on the switch after pressing dust cup on the concrete surface.
English 2. Rotation + Hammering Change Lever This rotary hammer can be set to rotation and hammering mode by pressing the push button and turning the change lever to mark. (Fig. 7) (1) Mount the drill bit. (2) Pull the trigger switch after applying the drill bit tip to the drilling position. (Fig. 8) (3) Pushing the rotary hammer forcibly is not necessary at all. Pushing slightly so that drill dust comes out gradually is just sufficient. Push Button Fig. 7 Fig.
English 䡬 Drill bit may snap off while disengaging the rotary hammer from the jammed hole. For disengaging, it is important to use a pushing motion or turn the drill bit counterclockwise. 䡬 Do not attempt to drill anchor holes or holes in concrete with the main unit in the rotation only function. 䡬 Do not attempt to use the rotary hammer in the rotation and striking function with the drill chuck and chuck adaptor attached. This would seriously shorten the service life of every components of the machine. 4.
English 6. Hammering only Change Lever This rotary hammer can be set to hammering only mode by pressing the push button and turning the change lever to mark. (Fig. 12) (1) Mount the bull point or cold chisel. (2) Press the push button and set the change lever to middle of mark and mark. (Fig. 13) Then rotation is released, turn the grip and adjust the cold chisel to desired position. (Fig. 14) (3) Turn the change lever to mark. (Fig. 12) Then bull point or cold chisel is locked. Push Button Fig.
English (4) To remove the drill bit (taper shank), insert the cotter into the slot of the taper shank adaptor and strike the head of the cotter with a hammer supporting on the rests. (Fig. 17) Cotter Taper Snank Adaptor Rests Fig. 17 HOW TO USE THE CORE BIT (FOR LIGHT LOAD) When boring penetrating large hole use the core bit (for light load). At that time use with the center pin and the core bit shank provided as optional accessories. 1.
English 2. How to bore (Fig. 21) (1) Connect the plug to the power source. (2) A spring is installed in the center pin. Push it lightly to the wall or the floor straight. Connect all over the surface of the core bit tip and start operating. (3) When boring about 3/16" (5 mm) in depth the position of the hole will establish. Bore after that removing the center pin and the guide plate from core bit.
English MAINTENANCE AND INSPECTION WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle during maintenance and inspection. 1. Inspecting the drill bits Since use of a dull tool will cause motor malfunctioning and degraded efficiency, replace the drill bit with a new one or resharpening without delay when abrasion is noted. 2. Inspecting the screws Regularly inspect all screws and ensure that they are properly tightened.
English 7. Service parts list A: B: C: D: Item No. Code No. No. Used Remarks CAUTION: Repair, modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed.
English ACCESSORIES WARNING: ALWAYS use Only authorized HITACHI replacement parts and accessories. NEVER use replacement parts or accessories which are not intended for use with this tool. Contact HITACHI if you are not sure whether it is safe to use a particular replacement part or accessory with your tool. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage. NOTE: Accessories are subject to change without any obligation on the part of the HITACHI.
English 䡬 Drill Bit (Taper shank) and taper shank adaptor (1) Drill Bit (Taper Shank) (2) Taper Shank Adaptor (SDS-plus shank) Cotter (Code No. 944477) External dia. 7/16" (11 mm) 1/2" (12.3 mm) 1/2" (12.7 mm) 9/16" (14.3 mm) 9/16" (14.5 mm) 11/16" (17.5 mm) 7/8" (21.5 mm) Code No. Taper mode Code No. Morse taper (No. 1) 303617 Morse taper (No. 2) 303618 A-taper 303619 B-taper 303620 944460 944461 993038 944462 944500 944463 944464 Applicable drill bit 7/16" (11 mm) 1/2" (12.
English 2. Knock-in anchor (Hammering only) Anchor Setter (for anchor setting) (SDS-plus shank) Anchor size Overall Length Code No. W 1/4" (6.3 mm) 10-1/4" (260 mm) 302976 W 5/16" (8 mm) 10-1/4" (260 mm) 302975 W 3/8" (9.5 mm) 6-1/4" (160 mm) 303621 10-1/4" (260 mm) 302974 Anchor size Overall Length Code No. W 1/4" (6.3 mm) 10-1/4" (260 mm) 302979 W 5/16" (8 mm) 10-1/4" (260 mm) 302978 W 3/8" (9.
English 3. Large hole boring (Rotation + Hammering) Guide Plate Center pin Center pin Core Bit Core bit Shank (SDS-plus shank) Code No. Core bit (outer diameter) Code No. – – (A) (A) 982684 (B) 982685 (B) 1" (25 mm) 1-1/8" (29 mm) 1-1/4" (32 mm) 1-3/8" (35 mm) 1-1/2" (38 mm) 1-3/4" (45 mm) 2" (50 mm) 982672 982673 982674 982675 982676 982677 982678 Core bit shank Overall length 4-1/8" (A) (105 mm) 12" (300 mm) 12" (B) (300 mm) Code No.
English 6. Grooving (Hammering only) Grooving Chisel (SDS-plus shank) Code No. 316659 7. Bolt placing operation with Chemical Anchor (Rotation + Hammering) ( Standard socket on the market ) (SDS-plus shank) 1/2" (12.7 mm) Chemical Anchor Adapter (Code No.303044) 3/4" (19 mm) Chemical Anchor Adapter (Code No. 303045) 8. Drilling holes and driving screws (Rotation only) 䡬 Drill chuck, chuck adaptor and chuck wrench Special screw Drill chuck (13VLRB–D) Chuck adaptor G Code No.
English 9. Drilling holes (Rotation only) Drill chuck (13VLD–D) Chuck adaptor (D) (includes chuck wrench) (SDS-plus shank) Code No. 321813 Code No. 303624 Chuck wrench 䡬 1/2" (13 mm) drill chuck ass’y (includes chuck wrench) and chuck (for drilling into steel or wood) 10. Driving Screws (Rotation only) Bit No. Chuck adaptor (D) (SDS-plus shank) Code No. 303624 Phillips Driver Bit Bit No. No. 2 No. 3 Screw Size 1/8" ~ 3/16" (3 – 5 mm) 1/4" ~ 5/16" (6 – 8 mm) Length 1” (25 mm) 1” (25 mm) Code No.
Français INFORMATIONS IMPORTANTES DE SÉCURITÉ Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions de fonctionnement dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé. La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé proviennent d’un non respect des règles ou précautions de base de sécurité.
Français SECURITE REGLES GENERALE DE SECURITE AVERTISSEMENT : Lire et coxmprendre toutes les instructions. Un non respect de toutes les instructions ci-dessous peut entraîner une électrocution, un incendie et/ou de sérieuses blessures personnelles. CONSERVER CES INSTRUCTIONS 1. Zone de travail (1) Garder la zone de travail propre et bien éclairée. Les établis mal rangés et les zones sombres invitent aux accidents.
Français 3. Sécurité personnelle (1) Rester sur ses gardes, regarder ce que l’on fait et utiliser son sens commun lors de l’utilisation d’un outil motorisé. Ne pas utiliser un outil en état de fatigue ou sous l’influence de drogues, d’alcool ou de médicaments. Un moment d’inattention lors de l’utilisation de l’outil motorisé peut entraîner de sérieuses blessures personnelles. (2) S’habiller correctement. Ne pas porter des vêtements larges ou des bijoux. Attacher les cheveux longs.
Français (6) Entretenir les outils avec soin. Conserver les outils de coupe propres et bien affûtés. Des outils correctement entretenus, avec des tranchants bien affûtés, sont moins susceptibles de se voiler et sont plus faciles à maîtriser. (7) Vérifier les défauts d’alignement ou grippage des parties mobiles, les ruptures des pièces et toutes les autres conditions qui peuvent affecter le fonctionnement des outils. En cas de dommage, faire réparer l’outil avant de l’utiliser.
Français 7. NE JAMAIS utiliser l’outil sans que tous les dispositifs de sécurité ne soient en place. NE JAMAIS faire fonctionner cet outil sans que tous les dispositifs et caractéristiques de sécurité ne soient en place et en état de fonctionnement. Si un entretien ou une réparation nécessite le retrait d’un dispositif ou d’une caractéristique de sécurité, s’assurer de bien remettre en place le dispositif ou la caractéristique de sécurité avant de recommencer à utiliser l’outil. 8. Utiliser l’outil correct.
Français 17. NE JAMAIS laisser fonctionner l’outil sans surveillance. Le mettre hors tension. Ne pas abandonner l’outil avant qu’il ne soit complètement arrêté. 18. Manipuler l’outil motorisé avec précaution. Si un outil motorisé tombe ou frappe un matériau dur accidentellement, il risque d’être déformé, fendu ou endommagé. 19. Ne pas essuyer les parties en plastique avec du solvant.
Français DOUBLE ISOLATION POUR UN FONCTIONNEMENT PLUS SUR Pour assurer un fonctionnement plus sûr de cet outil motorisé, HITACHI a adopté une conception à double insolation. “Double isolation” signifie que deux systèmes d’isolation physiquement séparés ont été utilisés pour isoler les matériaux conducteurs d’électricité connectés à l’outil motorisé à partir du cadre extérieur manipulé par l’utilisateur.
Français DESCRIPTION FONCTIONNELLE REMARQUE : Les informations contenues dans ce mode d’emploi sont conçues pour assister l’utilisateur dans une utilisation sans danger et un entretien de l’outil motorisé. NE JAMAIS utiliser ni entreprendre une révision de l’outil sans avoir d’abord lu et compris toutes les instructions de sécurité contenues dans ce manuel. Certaines illustrations dans ce mode d’emploi peuvent montrer des détails ou des accessoires différents de ceux de l’outil motorisé utilisé.
Français ASSEMBLAGE ET FONCTIONNEMENT APPLICATIONS Fonction de rotation et percussion 䡬 Perçage de trous d’ancrage 䡬 Perçage de trous dans béton 䡬 Perçage de trous dans une tuile Fonction de rotation seulement 䡬 Perçage de l’acier ou du bois (avec accessoires en option) 䡬 Serreage de vis mécaniques et de vis à bois (avec accessoires en option) Fonction de percussion seulement 䡬 Travaux légers de burinage de béton, de creusage de rainure et de cassure des angles AVANT L’UTILISATION 1.
Français 6. Montage du foret de perçage (Fig. 2) ATTENTION : Pour éviter tout accident, bien couper l’interrupteur et débrancher la fiche de la prise. REMARQUE : Lorsqu’on utilise des outils comme des pointes à broyer, des forets, etc., bien utiliser des pièces d’origine conçues par notre société. Elément de la tige SDS plus Capuchon avant Attache coulissante Foret de perçage Fig. 2 (1) Nettoyer la section de la queue du foret.
Français ATTENTION : 䡬 La capuchon à poussière et le collecteur à poussière (B) ne sont destinés à être utilisés que lors du perçage de béton. Ne pas les utiliser lors du perçage de pièces en bois ou métalliques. 䡬 Insérer le collecteur à poussière (B) à fond dans le mandrin de l’appareil principal particules pour ne utilisation pluse facile.
Français 䡬 Si l’on tire sur la gâchette et qu’on appuie sur la butée, l’outil continue à tourner tout seul, ce qui est pratique pour un travail continu. Pour arrêter l’outil, déconnecter la butée en tirant à nouveau sur la gâchette. Sélecteur 2. Rotation + percussion Boutonpoussoir Cette perceuse à percussion peut être mise sur le mode de rotation et frappe en appuyant sur le bouton pressoir et en tournant le sélecteur vers le repère . (Fig. 7) (1) Monter le foret de perçage.
Français (1) Fixer le mandrin porte-foret sur le raccord. (2) L’élément de la tige SDS est identique au foret de perçage. Se reporter à “Montage du foret de perçage” pour le fixer. ATTENTION : 䡬 Si l’on applique une force excessive, cela donnera un travail bâclé et abîmera la pointe du foret de perçage, réduisant ainsi la durée de service de le marteau rotatif. 䡬 La pointe du foret de perçage risque de se casser quand on dégage la perceuse coincée d’un trou qui vient d’être percé.
Français (2) Enfoncement de vis à bois 䡬 Avant d’enfoncer des vis à bois, préparez d’abord des trous appropriés aux vis utilisées dans le bois. Appliquez la mèche aux fentes de la tête de la vis et enfoncez la vis dans le bois en douceur. 䡬 Après avoir fait tourner le marteau rotatif à petite vitesse pendant un moment jusqu’à ce que la vis à bois soit partiellement enfoncée, pressez le trigger plus fortement afin d’obtenir la force d’entraînement maximale.
Français (1) Monter le raccord de queue conique sur le marteau rotatif à percussion. (Fig. 16) (2) Fixer la mèche (queue conique) sur le raccord de queue conique. (Fig. 16) (3) Mettre l’interrupteur sur la position de marche (ON) et percer un trou de la profondeur voulue. (4) Pour retirer la mèche (queue conique), introduire la clavette dans la fente du raccord de queue conique et frapper la tête de la clavette avec un marteau alors que le perceuse est placée sur le support. (Fig.
Français (4) Engager la plaque de guidage dans la couronne et tourner la plaque de guidage à gauche ou à droite de manière à ce qu’elle ne puisse pas tomber, même si elle orientée vers le bas. (Fig. 20) 2. Perçage (Fig. 21) (1) Brancher la perceuse. (2) Un ressort est placé dans le goujon central. Appuyer légèrement l’outil contre le mur ou le plancher tout droit. Toute la surface de la couronne doit être en contact avec le mur ou le plancher. Mettre en marche.
Français ENTRETIEN ET INSPECTION AVERTISSEMENT : S’assurer de mettre l’interrupteur d’alimentation sur la position OFF et de déconnecter la fiche de la prise secteur avant l’entretien et l’inspection de la meuleuse. 1. Contrôle du foret de perçage Etant donné que l’utilisation d’une mèche usée entraînera un mauvais fonctionnement du moteur et une diminution de l’efficacité, remplacez la mèche usée par une neuve ou aiguisez-la immédiatement et dès que vous notez une certaine usure. 2.
Français 7. Liste des pièces de rechange A: B: C: D: No. élément No. code No. utilisé Remarques PRECAUCIÓN : Les réparations, modifications et inspections des outils électriques Hitachi doivent être confiées à un service aprèsvente Hitachi agréé. Il sera utile de présenter cette liste de pièces au service aprèsvente Hitachi agréé lorsqu’on apporte un outil nécessitant des réparations ou tout autre entretien.
Français ACCESSOIRES AVERTISSEMENT : TOUJOURS utiliser UNIQUEMENT des pièces de rechange et des accessoires HITACHI. NE JAMAIS utiliser de pièce de rechange ou d’accessoires qui ne sont pas prévus pour être utilisé avec cet outil. En cas de doute, contacter HITACHI pour savoir si une pièce de rechange ou un accessoire particulier peuvent être utilisés en toute sécurité avec votre outil.
Français 䡬 Foret de perçage (queue conique) et raccord de queue conique (1) Foret de perçage (queue conique) (2) Raccord de queue conique (Tige SDS plus) Clavette (No. de code 944477) Dia. externe 7/16" (11 mm) 1/2" (12,3 mm) 1/2" (12,7 mm) 9/16" (14,3 mm) 9/16" (14,5 mm) 11/16" (17,5 mm) 7/8" (21,5 mm) No. de code Tupe de cône No. de code 944460 944461 Cône Morse (No. 1) 303617 Cône Morse (No.
Français 2. Ancrage de chasse (Percussion seulement) Régleur d’ancrage (pour fixation d’ancrage) (Tige SDS Plus) Dimension de l’ancrage Longueur totale No. de code W 1/4" (6,3 mm) 10-1/4" (260 mm) 302976 W 5/16" (8 mm) 10-1/4" (260 mm) 302975 W 3/8" (9,5 mm) 6-1/4" (160 mm) 303621 10-1/4" (260 mm) 302974 Dimension de l’ancrage Longueur totale No.
Français 3. Perçage de trou à large diamètre (Rotation + percussion) Plaque centrale de guidage Couronne Goujon Goujon No. de code – – Couronne (diamètre externe) No. de code (A) (A) 982684 (B) 982685 Queue de couronne (Tige SDS plus) (B) 1" (25 mm) 1-1/8" (29 mm) 1-1/4" (32 mm) 1-3/8" (35 mm) 1-1/2" (38 mm) 1-3/4" (45 mm) 2" (50 mm) 982672 982673 982674 982675 982676 982677 982678 Queue de couronne Longueur totale 4-1/8" (A) (105 mm) 12" (300 mm) 12" (B) (300 mm) No.
Français 6. Creusage de rainures (Percussion seulement) Burin à rainer (Tige SDS plus) No. de code 316659 7. Mise en place du booulon pour d’ancre chimique (Rotation + percussion) ( Douille standard du marché ) (Tige SDS Plus) 1/2" (12,7 mm) Raccord d’ancre chimique (No. de code 303044) 3/4" (19 mm) Raccord d’ancre chimique (No. de code 303045) 8. Perçage de trous et insertion des vis (Rotation seulement) 䡬 Mandrin porte-foret, raccord (G) de mandrin, vis spéciale et clé de mandrin Vis spéciale No.
Français 9. Perçage de trous (Rotation seulement) Mandrin porte-foret (13VLD-D) (y compris la clé de mandrin) No. de code 321813 Raccord (D) de mandrin (Tige SDS plus) No. de code 303624 Clé de mandrin 䡬 Ensemble du mandrin porte-foret de 1/2" (13 mm) (y compris la clé de mandrin) et mandrin (pour percer l’acier ou le bois) 10. Vis d’entraînement (Rotation uniquement) No. de mèche Raccord (D) de mandrin (Tige SDS plus) No. de code 303624 Embout de vissage Phillips No. de mèche No. 2 No.
Español INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD Antes de utilizar o de realizar cualquier trabajo de mantenimiento de esta herramienta eléctrica, lea y comprenda todas las precauciones de seguridad, advertencias e instrucciones de funcionamiento de este Manual de instrucciones. La mayoría de los accidentes producidos en la operación y el mantenimiento de una herramienta eléctrica se deben a la falta de observación de las normas o precauciones de seguridad.
Español SEGURIDAD NORMAS GENERALES DE SEGURIDAD ADVERTENCIA: Lea y entienda todas las instrucciones. Si no sigue las instrucciones indicadas a continuación, pueden producirse descargas eléctricas, incendios, y/o lesiones serias. GUARDE ESTAS INSTRUCCIONES 1. Área de trabajo (1) Mantenga el área de trabajo limpia y bien iluminada. Los bancos de trabajo desordenados y las áreas obscuras pueden conducir a accidentes.
Español 3. Seguridad personal (1) Esté siempre alerta y utilice el sentido común cuando utilice la herramienta eléctrica. No utilice la herramienta cuando esté cansado o bajo la influencia de medicamentos ni de alcohol. Un descuido al utilizar la herramienta eléctrica puede resultar en una lesión seria. (2) Vístase adecuadamente. No utilice ropa floja ni joyas. Si tiene pelo largo, recójaselo. Mantenga su pelo, ropa, y guantes alejados de las partes móviles.
Español (6) Realice el mantenimiento cuidadoso de las herramientas. Mantenga las herramientas afiladas y limpias. Las herramientas adecuadamente mantenidas, con los bordes cortantes afilados, serán más fáciles de utilizar y controlar. (7) Compruebe que las piezas móviles no estén desalineadas ni atascadas, que no hayan piezas rotas, y demás condiciones que puedan afectar la operación de las herramientas. En caso de que una herramienta esté averiada, repárela antes de utilizarla.
Español 6. NO toque NUNCA las piezas móviles. NO coloque NUNCA sus manos, dedos, ni demás partes del cuerpo cerca de las piezas móviles de la herramienta. 7. NO utilice NUNCA la herramienta sin los protectores colocados en su lugar. NO utilice NUNCA esta herramienta sin los protectores de seguridad correctamente instalados. Si el trabajo de mantenimiento o de reparación requiere el desmontaje de un protector de seguridad, cerciórese de volver a instalarlo antes de utilizar la herramienta. 8.
Español 16. NO utilice NUNCA una herramienta defectuosa o que funcione anormalmente. Si la herramienta parece que funciona anormalmente, produciendo ruidos extraños, etc., deje inmediatamente de utilizarla y solicite su arreglo a un centro de reparaciones autorizado por Hitachi. 17. NO deje NUNCA la herramienta en funcionamiento desatendida. Desconecte su alimentación. No deje sola la herramientas hasta mientras no se haya parado completamente. 18. Maneje con cuidado las herramientas eléctricas.
Español AISLAMIENTO DOBLE PARA OFRECER UNA OPERACIÓN MÁS SEGURA Para garantizar una operación más segura de esta herramienta eléctrica, HITACHI ha adoptado un diseño de aislamiento doble. “Aislamiento doble” significa que se han utilizado dos sistemas de aislamiento físicamente separados para aislar los materiales eléctricamente conductores conectados a la fuente de alimentación del bastidor exterior manejado por el operador.
Español DESCRIPCIÓN FUNCIONAL NOTA: La información contenida en este Manual de instrucciones ha sido diseñada para ayudarle a utilizar con seguridad y mantener esta herramienta eléctrica. NUNCA haga funcionar ni efectúe el mantenimiento de la herramienta antes de leer y comprender todas las instrucciones de seguridad contenidas en este manual. Algunas ilustraciones de este Manual de Instrucciones pueden mostrar detalles o accesorios diferentes a los de la propia herramienta eléctrica.
Español MONTAJE Y OPERACIÓN APLICACIONES Función de rotación y golpeteo 䡬 Perforación de orificios de anclaje 䡬 Perforación de orificios de hormigón 䡬 Perforación de orificios de baldosa Función de rotación solamente 䡬 Perforación de orificios en hormigón o madera (con accesorios facultativos) 䡬 Apretar tornillos en metal o madera (con accesorios facultativos) Función de percusión solamente 䡬 Cincelado leve de hormigón, ranuración, y retoque de bordes ANTES DE LA OPERACIÓN 1.
Español 6. Montaje de la broca (Fig. 2) PRECAUCIÓN: Para evitar accidentes, cerciórese de desactivar y de desconectar el enchufe del tomacorriente. NOTA: Cuando ulilice herramientas como por ejemplo: cinceles, brocas de taladro, etc., cerciórese de utilizar piezas genuinas diseñadas por nuestra compañía. (1) Limpie la parte del vástago de la broca de taladro. (2) Inserte la broca de taladro girando en el sujetador de la herramienta hasta que se asegure bien. (Fig.
Español PRECAUCIÓN: 䡬 La copa de polvo y el colector de polvo (B) son para emplearse exclusvamente en trabajos de perforación de hormigón. No los emplee para trabajar con madera o metal. 䡬 Inserte completamente el colector de polvo (B) en la parte del portabrocas de la unidad principal. 䡬 Cuando ponga en funcionamiento del martillo perforador meintras el colector de polvo (B) esté separado de la superficie de hormigón, dicho colector girará junto con la broca.
Español 䡬 Tire del gatillo y empuje el tope para mantener activada la alimentación, lo cual es conveniente para un funcionamiento continuo. Cuando se lo desconecta, el tope puede quitarse tirando del gatillo otra vez. Palanca selectora 2. Rotación + golpeteo Este martillo roto-percutor puede usarse en el modo de rotación y golpeteo presionando el pulsadory girando la palanca selectora hasta la marca . (Fig. 7) (1) Montar la broca.
Español PRECAUCIÓN: 䡬 La aplicación de fuerza excesiva acelerará el trabajo pero dañará la punta de la broca y reducirá la vida útil del martillo perforador. 䡬 La broca puede salirse al quitar el martillo perforador del orificio en el que se haya atascado. Para extraer esta herramienta es importante empujar hacia adelante, o gire la broca hacia la izquierda. 䡬 No intentar perforar orificios de anclaje o perforar el concreto con la máquina puesta en la función de rotación solamente.
Español 䡬 Luego de hacer rotar la herramienta lentamente hasta que el tornillo quede parcialmente metido en la madera, apretar más el gatillo para obtener la fuerza óptima de atornillado. PRECAUCIÓN: 䡬 Tener cuidado al preparar el orificio para que sea apropiado para el tornillo, teniendo en cuenta la dureza de la madera. Si el orificio es excesivamente pequeño o estrecho, se requiere mucha fuerza para atornillar y a veces puede Palanca selectora dañarse la rosca. 6.
Español (4) Para quitar la broca (espiga ahusada), insertar la chaveta en la ranura del adaptador de la espiga ahusada y golpear la cabeza de la chaveta con un martillo. Usar apoyos como se muestra en la Fig. 17. Sujetador Broca Adaptador de la espiga ahusada Cubierta frontal Fig. 16 Adaptador de la espiga ahusada Chaveta Apoyo Fig. 17 MODO DE USAR LA BARRENA TUBULAR (PARA CARGAS LIGERAS) Cuando se tengan que taladrar agujeros grandes, usar la barrena tubular (para cargas ligeras).
Español (4) Unir la placa guía con la barrena tubular y girar la placa guía hacia la izquierda o hacia la derecha de forma que no se caiga a pesar de estar indicando hacia abajo. (Fig. 20) 2. Modo de taladrar (Fig. 21) (1) Conectar el enchufe a la toma de alimentación. (2) El pasador central se ha instalado un resorte. Presionar ligeramente y sin torcerse hacia la pared o hacia el pared o hacia el suelo.
Español MANTENIMIENTO E INSPECCIÓN ADVERTENCIA: Antes de realizar el mantenimiento o la inspección de la amoladora, cerciórese de desconectar la alimentación y de desenchufar el cable de alimentación del tomacorriente. 1. Inspeccionar la broca de taladro Debido a que el uso de brocs desafiladas pueden causar mal funcionamiento del motor y desmejorar la eficacia del taladro, hay que reemplazar las brocas en malas condiciones por nuevas o afilarlas de inmediato al advertir abrasión. 2.
Español 7. Lista de repuestos A: Nº. ítem B: Nº. codigo C: Nº. usado D: Observaciones PRECAUTION: La reparación, modificación e inspección de las herramientas eléctricas Hitachi deben ser realizadas por un Centro de Servicio Autorizado de Hitachi. Esta lista de repuestos será de utilidad si es presentada junto con la heramienta al Centro de Servicio Autorizado de Hitachi para solicitar la reparación o cualquier otro tipo de mantenimiento.
Español ACCESORIOS ADVERTENCIA: SIEMPRE utilice únicamente repuestos y accesorios autorizados por HITACHI. NO utilice NUNCA repuestos o accesorios no previstos para usar con esta herramienta. Si tiene dudas en cuanto a la seguridad de usar determinado repuesto o accesorio junto con su herramienta, póngase en contacto con HITACHI. La utilización de otros accesorios puede resultar peligrosa y causar lesiones o daños mecánicos.
Español Diámetro externo Núm. de código 7/16" 944460 (11 mm) 1/2" 944461 (12,3 mm) 1/2" 993038 (12,7 mm) 9/16" 944462 (14,3 mm) 9/16" 944500 (14,5 mm) 11/16" 944463 (17,5 mm) 7/8" 944464 (21,5 mm) Modo cónico Núm. de código Cono Morse (No. 1) 303617 Cono Morse (No.
Español Medida de ancla Longitud total Núm. de código W 1/4" (6,3 mm) 10-1/4" (260 mm) 302976 W 5/16" (8 mm) 10-1/4" (260 mm) 302975 W 3/8" (9,5 mm) 6-1/4" (160 mm) 303621 10-1/4" (260 mm) 302974 Medida de ancla Longitud total Núm.
Español Pasador central Núm. de código – – (A) 982684 (B) 982685 Barrena tubular (diámetro externo) 1" (25 mm) 1-1/8" (29 mm) (A) 1-1/4" (32 mm) 1-3/8" (35 mm) 1-1/2" (38 mm) 1-3/4" (45 mm) (B) 2" (50 mm) Núm. de código 982672 982673 982674 982675 982676 982677 982678 Espiga de la Núm. de código barrena tubular Longitud total 4-1/8" 303625 (A) (105 mm) 12" 303626 (300 mm) 12" (B) 303627 (300 mm) Placa guia Barrent tubular Barrena tubular Núm. de código Núm.
Español 7. Trabajo de colocación de pernos para anclaje químico (Rotación + golpeteo) Manguito adaptador a la venta el mercado (SDS más vástago) Adaptador de anclaje químico de 1/2" (12,7 mm) (Núm. de código 303044) Adaptador de anclaje químico de 3/4" (19 mm) (Núm. de código 303045) 8. Perforación (Rotación solamente) 䡬 Portabrocas, adaptador (G) del portabrocas, tornillo especál y llave de portabrocas Tornillo especial Núm.
Español 10. Colocación de tornillos (Rotación solamente) No. de broca Adaptador (D) del portabrocas (SDS más vástago) Núm. de código 303624 Broca para tornillos Phillips No. de broca No. 2 No. 3 Tamaño del tornillo 1/8" ~ 3/16" (3 – 5 mm) 1/4" ~ 5/16" (6 – 8 mm) Longitud 1" (25 mm) 1" (25 mm) Núm. de código 971511Z 971512Z 11. Copa de polvo, Colector de polvo (B) Copa de polvo Núm. de código 971787 Colector de polvo (B) Núm. de código 306885 12.
A B C 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 306-345 306-340 322-809 322-810 322-811 322-812 984-118 939-547 301-654 323-178 ———— 322-789 317-223 323-179 878-885 317-238 307-688 322-815 323-232 690-4DD 322-819 322-813 959-156 323-184 323-185 317-233 317-234 317-235 322-803 944-486 322-804 322-802 322-805 322-808 322-806 322-807 322-801 322-834 322-800 322-793 322-792 322
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● Lead from lead-based paints, ● Crystalline silica from bricks and cement and other masonry products, and ● Arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.