Manual

12
Examine your kit carefully!
MULTIPLEX model kits are subject to constant quality checks throughout the production process, and we sincerely hope that you
are satisfied with the contents of your kit. However, we would ask you to check all the parts before you start construction, referring
to the Parts List, as we cannot exchange components which you have already modified. If you find any part is not acceptable
for any reason, we will readily correct or exchange it once we have examined it. Just send the component to our Model Department,
with adequate pre-paid carriage, and be sure to include the completed complaints form. We are constantly working on improving
our models, and for this reason we must reserve the right to alter the kit contents in terms of shape or dimensions of parts,
technology, materials and fittings, without prior notification. Please understand that we cannot entertain claims against us if the
kit contents do not agree in every respect with the instructions and the illustrations.
Caution!
Radio-controlled models, and especially model aircraft, are by no means playthings in the usual sense of the word.
Building and operating them safely requires a certain level of technical competence and manual skill, together with
discipline and a responsible attitude at the flying field.
Errors and negligence in building and flying the model can result in serious personal injury and damage to property. Since
we, as manufacturers, have no control over the construction, maintenance and operation of our products, we are obliged
to take this opportunity to point out these hazards and to emphasize your personal responsibility.
Airborne radio control system components
Recommended equipment:
Min. MULTIPLEX RX-5 light M-LINK receiver, Order No. 5 5808
or RX-6-DR light M-LINK, Order No. 5 5809
Two Nano-S servos (rudder + elevator), Order No. 6 5120
Optional: two additional Nano-S servos, Order No. 6 5120
(for ailerons)
Two 30 cm servo extension leads, Order No. 8 5031
Power set:
“EASYStar II” power set, Order No. 33 2622
containing brushless motor, speed controller, folding propeller, driver, spinner and accessories.
Power set:
“EASYStar II” power set, Li-BATT powered, Order No. 33 3622
Brushless motor, speed controller, folding propeller, driver, spinner and accessories, Li-BATT ECO flight pack, 3/2000
(M6)
Recommended battery:
Li-BATT ECO 3/1-2000 (M6), Order No. 15 7231
Adhesive: Zacki ELAPOR ® 20 g, Order No. 59 2727
Zacki ELAPOR ® Super liquid 10 g, Order No. 59 2728
Battery charger:
MULTIcharger LN-3008 EQU with 230 V / 12 V AC/DC mains PSU, 5.0 A, Order No. 9 2545
Tools:
Scissors, balsa knife, combination pliers, 4 - 5 mm Ø bradawl or small round file.
Important note
This model is not made of Styrofoam™, and it is not possible to glue the material using white glue, polyurethane or epoxy
adhesives.
These glues only produce a superficial bond which fails immediately when stressed. Please be sure to use medium-viscosity
cyano-acrylate glue exclusively - ideally our Zacki -ELAPOR® # 59 2727, the super-glue designed and optimized expressly for
ELAPOR® particle foam. If you use Zacki-ELAPOR®, you usually do not need cyano activator (kicker). However, if you prefer to
use a different cyano, and therefore have to use activator, always use the spray in the open air to avoid the unpleasant fumes.
Please take care when handling cyano-acrylate adhesives; these materials harden in seconds, so avoid getting them on your
fingers or other parts of the body. We strongly recommend the use of goggles to protect your eyes. Keep the adhesive out of the
reach of children.
GB
Order No. 21 4260