OPERATION MANUAL Ver 1.0 www.hitecrcd.
table of contents Section 1 Introduction..........................................................................................................................................................................3 Warnings and Safety Instructions.................................................................................................................................3 Features and Specifications.............................................................................................................
Section 1 Introduction Thank you for purchasing the Weekender Extra 300S radio controlled model. The Extra 300S is the perfect answer for the novice pilot looking to expand into the world of aerobatic flight. Built with a pre-painted, durable EPO airframe and featuring a powerful brushless motor, the Extra 300S promises hours of weekend high-flying fun! Warning, Caution, Tip and Note Boxes Warning: Be sure to read this section for your own safety.
FEATuRES AND SPECIFICATIONS features • • • • • Specifications Durable pre-painted EPO airframe can easily be assembled in less than 45 minutes Powerful preinstalled brushless outrunner motor and 50Amp ESC gives the Extra 300S plenty of power for aerobatic flight Preinstalled 17 gram micro servos Removable cowl for ease of motor and ESC access 8 Minute + runtimes when used with recommended battery • Wingspan: 47.2 in (1200 mm) • Length: 42.5 in (1088 mm) • Weight: 3.
Section 2 ASSEMBLY INSTRuCTIONS Before Assembling the Extra 300S Keep in mind when assembling and flying the Extra 300S, that radio control model airplanes may cause injury or property damage when improperly flown or mishandled. Always follow the warnings written in the instruction manual. Improper usage could lead to damage and/or failure of the electronic equipment. Be sure to read this instruction manual in its entirety before assembling and flying this model.
ASSEMBLY INSTRuCTIONS (cont.) SteP 5 SteP 6 Step 5: attaching the Rudder Holding the top of the vertical stabilizer, snap the rudder into place ensuring that it moves freely on the hinges. SteP 7 Step 6: connecting the Rudder control arm linkage Take the remaining control linkage and slide the Z bend through the middle hole of the rudder control horn. Slide the other end into the swivel on the servo. Tighten the screw just enough to hold the wire in position.
ASSEMBLY INSTRuCTIONS (cont.) SteP 9 Step 9: Propeller Hub and Spinner assembly Take the propeller hub and slide it through the base of the spinner assembly, then slide the propeller on the hub and spinner base. Install the washer and nut, do not tighten. Slide this assembly onto the motor shaft and tighten the nut. Place the spinner over the propeller and attach with the supplied screw. Once tightened, the distance between the cowl and spinner should be about 4 mm.
ASSEMBLY INSTRuCTIONS (cont.) SteP 12 Step 12: balancing Your Model Check the center of gravity (CG) on your model by balancing it on your fingers. The CG should be about 3 ~ 3.4 inches (76 ~ 86 mm) behind the leading edge of the model as shown below. You can adjust the CG by moving the battery forward or backwards. 76 ~ 86 mm Section 3 PREPARING FOR FLIGHT Speed control operation The ESC is set for optimal performance at the factory and should not be changed.
Section 4 SPARE PARTS 61020 Fuselage 61023 Vertical Stabilizer 61026 Wheel Covers 61029 Tail Landing Gear 61032 Controlling Linkage Steel Wire 61035 50A Brushless ESC 61021 61022 Main Wings Horizontal Stabilizer 61024 61025 Cowling Main Landing Gear 61027 61028 Main Wheels Fixing Screws for Main Wheels 61030 61031 Spinner Propeller Connecting Shaft 61033 61034 Tail Wheel Springs 61036 Brushless Motor D3720-630Kv 9 Screws Package
service and support Weekender by Hitec Customer Service Help is available from Hitec RCD USA, Inc. Customer Service through phone support: (858) 748-6948 and e-mail: service@hitecrcd.com. Our office is generally open Monday through Friday, 8:00 AM to 4:30 PM PST. These hours and days may vary by season. Every attempt is made to answer all incoming service calls. Should you get our voice mail, please leave your name and number and a staff member will return your call.
Notes 11
www.hitecrcd.