user manual

ManualsBrandsHitec ManualsHobbyHHFP30 programming box

Instruction Manual

Introduction

Contents

Programming

Congratulations on the purchase of the HFP-30. The HFP-30 is

designed to program all Hitec Digital Programmable Servos (D Series,

5xxx/7xxx, and Brushless) as well as test any brand servo.

Layout

Powering On

Main Screens

1. Main Programming Screen

2. Main Servo Test Screen

Test Mode

1. Manual Test

2. Auto Test

3. Auto Deadband Testing

4. Settings

D Series Program Mode

1) Set EPA/Neutral

2) Servo Sync

3) Set Rotation (CW_CCW)

4) Set Deadband (DB_Width)

5) Set Speed

6) Set ID (ID_Read)

7) Set Failsafe

8) Set Soft Start

9) Factory Reset (Factory Default Set)

5/7 Series Program Mode (For 5xxx*/7xxx Servos)

1) Set EPA/Neutral

2) Servo Sync

3) Set Rotation (CW_CCW)

4) Set Deadband (DB_Width)

5) Set Speed

6) Set Failsafe

7) Set Resolution

8) Set Overload Protection (OLP)

9) Factory Reset (Factory Default Set)

1. Adjust Dial

2. Back Button

3. Analog Dial for Pulse Adjustment

4. USB Port

5. Test/Program Select Switch

6. Battery/Receiver Port

7. Servo Sync Port

8. Servo Port

9. LCD

B Series Program Mode (BLDC Servos)

1) Set EPA/Neutral

2) Servo Sync

3) Set Rotation (CW_CCW)

4) Set Deadband (DB_Width)

5) Set Speed

6) Set Failsafe

7) Set Soft Start

8) Factory Reset (Factory Default Set)

The HFP-30 is powered by a user provided 4.8VDC to 7.4VDC battery

pack plugged into the Batt/RX slot. Optionally, a receiver with the

correct adapter can power the unit.

Note: Make sure the battery voltage corresponds to the servos

being used. Do not use a 7.4V battery with a servo designed for

6V and under, or damage may occur to the servo.

Depending on the position of the Test/Program select switch, the

following screens will appear when powered on. Once powered on,

it is possible to toggle between the screens using the Test/Program

switch.

Main Programming Screen

Use the Adjust Dial to switch between the three dierent series of

servos. Once the correct one is highlighted, press the Adjust Dial to

enter.

Layout

Contents

Powering On

Main Screens

Summary of content (6 pages)

PAGE 1
B Series Program Mode (BLDC Servos) 1) 2) 3) 4) 5) 6) 7) 8) Set EPA/Neutral Servo Sync Set Rotation (CW_CCW) Set Deadband (DB_Width) Set Speed Set Failsafe Set Soft Start Factory Reset (Factory Default Set) Contents Layout Instruction Manual Introduction 1. 2. 3. 4. 5. 6. 7. 8. 9. Adjust Dial Back Button Analog Dial for Pulse Adjustment USB Port Test/Program Select Switch 7 Battery/Receiver Port Servo Sync Port Servo Port LCD 3 8 6 Congratulations on the purchase of the HFP-30.
PAGE 2
Main Servo Test Screen AUTO-Extreme Use the Adjust Dial to select the desired test function. Once the function is highlighted, press the Adjust Dial to enter. Test Mode In this mode, all manufacturer’s servos can be tested for operation. To begin testing servos, plug a servo into the servo slot on the programmer and install the correct battery type in the battery slot. Move the select switch to the TEST position. 1. Manual test Using the Adjust Dial, highlight Manual, and press then Adjust Dial to enter.
PAGE 3
Settings D Series Program Mode 1. EPA Neutral Settings The Settings menu is where specific test parameters can be set for all servo test modes. Use the Adjust Dial to highlight SETTING and press it to enter the menu. To make adjustments to the various settings, use the Adjust Dial to highlight it and then press the dial to enter editing mode. To change the value, use the Adjust Dial. Either press it again to confirm and exit or press the BACK button to exit without saving.
PAGE 4
. Deadband (DB_Width): Highlight DB_Width on the main screen and press the Adjust Dial to enter the menu. Note: Hitec Digital Servos from the factory are set to the tightest Deadband possible by default. Even if the Deadband can be set lower with the programmer, it will have no effect on the servo. Once in the menu, the current Deadband is displayed under Now Values. Use the Adjust Dial to change the value under the ‘Set Values’.
PAGE 5
3. Rotation (CW_CCW) Highlight CW_CCW on the main screen and press the Adjust Dial to enter the menu. Under the Now Values will be the current rotation direction. Below will be the value to set. Use the Adjust Dial to change from CW to CCW. Once at the desired rotation, press the Adjust Dial to save the value to the Now Values. Press the BACK button to exit to the main menu. degrees. If turned off, total programmable throw is 180 degrees.
PAGE 6
2. Servo Sync To match two servos together, use the Servo Sync option when programming Neutral and Endpoints. The first step is to program and save the first servo at the desired positions. Exit the programming mode and then place the programmed servo into the SYNC slot of the HFP-30. Place the next servo into the Servo slot and enter the programming mode. Enter the EPA and Neutral Setting menu and begin programming the servo.