Digital Photo Printer P910L Operation Manual
Handling of this Manual 1. All rights reserved. No part of this operation manual covered by the copyright herein maybe reproduced or copied in any form or by any means, including translation, without the written permission of HiTi Digital, Inc. 2. The specifications in this operation manual are subject to change without prior notice. 3. In case of having any difficulties or finding the fault in this manual, your information to HiTi Digital will be highly appreciated.
CONTENTS PREFACE Chapter 1. Important Safety Instruction ・・・・・・・・・・・・・・・・・ Environments ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ Handling Instruction ・・・・・・・・・・・・・・・・・・・・・・・・・・ Handling Instruction for Consumable and Printed Output ・・・・・・ 1-1 Chapter 2.
Chapter 1. Important Safety Instruction This manual provides detailed instructions for Environments the safety use of the printer. Read this manual before operating the printer to ensure to have proper use. To use the printer safety, please pay attention to the followings: ◆In this manual, there are notes that require special attention. ◆ For your safety operation, Safety notices are Caution: Do not let children to touch the printer or the cables. It can cause accidents or electric shock.
Chapter 1. Important Safety Instruction Handling Instruction In handling the printer, please pay attention to the followings; Warning: Lift the printer from its box and put it onto a flat table or desk. Warning: At nearly 13.5Kg, the printer is too heavy to be lifted by one person. Also please take a good care of your hands and fingers when lifting the printer from the box. Warning: Be careful when you transport the printer on the slippery floor.
Chapter 1. Important Safety Instruction Handling Instruction for Consumable and Printed Output In handling the ink ribbon, paper and printed output, please pay attention to the followings; Attention: Paper Handling ・Use the paper specified by HiTi Digital. ・Store the paper flat. ・ Store the paper in a dry and dark place to avoid the direct Sunlight. (Temperature less than 30°C, Humidity less than 60%). ・Do not touch the paper surface before printing to avoid the fingerprints.
Chapter 2. Installing and Set Up This chapter explains the unpacking and set up of the printer. Before proceeding to this chapter, please make sure to read Chapter 1. Important Safety Instruction. Unpacking and Checking the Accessories 1. Open the box and remove the box containing the accessories and protection materials. Attention: Keep the packaging materials. The box and protection materials are necessary when moving or transporting the printer. Make sure that they are retained. 2.
Chapter 2. Installing and Set Up Parts Name and Function ④ ① ② ③ ⑤ ⑥ ( Front View) ( Rear View) ⑦ ⑨ ⑧ (Front Internal View) № Name (Upper Internal View) Function ① Printer Status Lamps Printer status display lamps are located on the panel. ② Drawer Unit Open the drawer unit when replacing an ink ribbon or paper, or when performing maintenance. ③ Drawer Lever When open the drawer unit, hold this lever. ④ Power Switch This switch turns on/off the power of the printer.
Chapter 2. Installing and Set Up Printer Status Lamps Name and Printer Status Printer status lamp display ●:on, ○:off, ＊:flashing LED Display Description POWER MEDIA ERROR ○ ○ ○ ＊ ○ ○ ● ○ ○ ● ○ ＊ The drawer unit is opened. ● ○ ● Paper jam occurred. The printer mechanical section is faulty. Trouble of printer control board. ● ＊ ● The ink ribbon loaded is not supported. ● ● ● ● ＊ ○ The power of printer is off.
Chapter 2. Installing and Set Up Connecting Power Cable Connecting USB Cable Insert the power cable attached to the printer into the power connector located on the rear of the printer. Connect the USB cable from the personal computer to the USB connector located on the left rear side of the printer. Be sure to insert the USB cable all the way. Warning: Make sure to turn off the power of the printer before inserting the power cable. Warning: Make sure to insert the power cable correctly.
Chapter 2. Installing and Set Up Setting Ink Ribbon 1. Remove dust box. 4. Take the slack the ink ribbon by turning the ink ribbon supply core. 2. Carefully lift the drawer lever and pull the drawer unit. Attention: Do not open the drawer unit quickly or with unnecessary force. Do not press the drawer unit or place a heavy object other than paper after opening the drawer unit. 3.
Chapter 2. Installing and Set Up 3. Set the paper in the printer. Loading Paper Turn on the power of the printer by pressing "|" on the power switch. Set the paper by matching the color of the paper flange and the color of the holder. After setting the paper, remove the seal 1. In the drawer unit pull out, pull the from the paper. Blue lever to open the open guide unit. Pull out the drawer unit and pull the lever to open the open guide unit. White 4.
Chapter 2. Installing and Set Up Installing Dust Box Insert the claw of the dust box first and insert the projected section of the printer in the hole at the bottom of the dust box. Claw Transporting the Printer The following cautions are necessary in transportation of the printer. Since an incorrect transportation method causes a printer fault, follow the correct method. 1. Remove the ink ribbon and paper from the printer before transporting the printer.
