User's Manual

ManualsBrandsHiTi Digital ManualsComputers & AccessoriesDigital Photo Printer

Chapter 3. Routine Maintenance

3-1

Cleaning of Thermal Head, Platen

By using thermal transfer technology, daily maintenance is not really necessary if the printer is

being use properly.

However, in order to keep the best print quality, it is recommended to do the cleaning of Thermal

Head and Platen once in a month.

Using gauze, clean the heat element (glass

bar) of the thermal head with isopropyl

alcohol or ethyl alcohol.

Using gauze dipped with isopropyl alcohol or

ethyl alcohol, clean the edge of the peeling

roller.

Using gauze dipped with isopropyl alcohol or

ethyl alcohol, clean the rubber section of the

platen roller

Caution:

Make sure that the power is turned off before starting cleaning.

Thermal Head reaches high temperature just after printing. Do not touch directly

by hand. Make sure that the thermal head has been sufficiently cooled down before

starting cleaning.

When fingerprint stick to the heat element, it can damage the Thermal Head. Do

not touch directly by hand.

Be careful not to be hurt by the projections of the printer.

Attention:

Printing should be performed after the alcohol dried up completely

(approx. 5 minutes)

Summary of content (9 pages)

PAGE 1
Chapter 3. Routine Maintenance Cleaning of Thermal Head, Platen By using thermal transfer technology, daily maintenance is not really necessary if the printer is being use properly. However, in order to keep the best print quality, it is recommended to do the cleaning of Thermal Head and Platen once in a month. Caution: Make sure that the power is turned off before starting cleaning. Thermal Head reaches high temperature just after printing. Do not touch directly by hand.
PAGE 2
Chapter 3. Routine Maintenance Cleaning of Outer Cover Wipe the printer outer cabinet with a soft cloth. If the stains are not removed, wet the cloth and apply weakened neutral Detergent to it. Warning: In case, the foreign substance get into the printer, turn off the power of printer, remove the power cable and contact the dealers or service center. Continuous use of the printer under such condition can cause the fire and electric shock.
PAGE 3
Chapter 4. Error Handling Printer Status lamps are displayed in red When the error happens, the details of the error can be confirmed with the printer status lamps. Printer Status Lamps and Paper Setting Lamp display ●:on、○:off、＊:flashing ／ : Indicates that irrespective lit LED Display Status Corrective Action MEDIA ERROR PAPERSET ○ ＊／ The drawer unit is opened. Close the drawer unit. ○ ● ＊ Paper jam occurred. Remove the paper. If paper jam occurs frequently, consult with the service center.
PAGE 4
PAGE 5
Chapter 4. Error Handling Paper Jam 1. Open the drawer unit. 2. Cut off the folded section or printed section with scissors. When the paper is folded inside of the printer, pull it out slowly. Power Supply Interrupted during Printing In case, power supply interrupted during the printing, Thermal Head will be kept pushing to Platen. Leaving this situation for a long time, shape of Platen can be warped. In order to avoid this situation, please follow the instruction below. 1. 2. 3.
PAGE 6
PAGE 7
Chapter 5. In order to more comfortably use Paper Pre-Cut function can be turned off through the printer driver. Caution: Dust on the surface of the paper may damage the thermal head. Clean the dust on the paper surface and install the paper roll into the printer. Caution: Clean the finger print on the paper surface to avoid the finger print on the print image. Caution: Paper may be installed and fixed on improper direction, but maybe oblique direction.
PAGE 8
Chapter 5. In order to more comfortably use For the Customers in the U.S.A. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
PAGE 9
Specification Product name Model name Printing method Resolution Print sizes Print media Operating environment Paper feeding Dimensions temperature humidity Weight Power voltage Power consumption Interface Buffer Memory Digital Photo Printer P910L Dye sublimation thermal transfer 12 dots/mm (300 dpi) 203 mm x 305 mm (8 x 12 size) 203 mm x 254 mm (8 x 10 size) 203 mm x 203 mm (8 x 8 size) 203 mm x 152 mm (8 x 6 size) 203 mm x 127 mm (8 x 5 size) 203 mm x 102 mm (8 x 4 size) Paper 203 mm (8 in.